Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33K0E _51 Engine / Hybrid System _043566 1KD-FTV ENGINE CONTROL _0222113 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay circuit

·

Ignition switch

·

Park/neutral position switch assembly*

·

ECM


Comes on DTC stored

*: for Automatic Transmission

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

P0617
DTC Detection Drive Pattern Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

w/o Smart Entry and Start System
A358197E03
1.646,1.573 2.74,1.792 1.094,0.219 10 false Ignition Switch 1.646,1.406 2.063,1.583 0.417,0.177 10 false G133 2.75,1.125 3.844,1.344 1.094,0.219 10 false STA/WIPER-S 2.885,2.073 3.677,2.49 0.792,0.417 10 false Clutch Start Switch*2 2.885,1.906 3.198,2.094 0.313,0.188 10 false B2 4.396,2.063 5.365,2.635 0.969,0.573 10 false Park/Neutral Position Switch Assembly*1 4.396,1.875 4.833,2.073 0.438,0.198 10 false C22 5.51,1.656 5.948,1.854 0.438,0.198 10 false 4 5.49,2.438 5.927,2.635 0.438,0.198 10 false 5 3.781,2.448 4.219,2.646 0.438,0.198 10 false 1 3.771,1.625 4.208,1.823 0.438,0.198 10 false 2 6.292,4.115 6.708,4.313 0.417,0.198 10 false ECM 6.292,3.938 6.708,4.135 0.417,0.198 10 false G130 0.552,1.865 1.646,2.083 1.094,0.219 10 false AM2 NO. 2 0.542,2.531 1.635,2.75 1.094,0.219 10 false J/B-B 0.563,4.635 1.656,4.854 1.094,0.219 10 false FL MAIN 3.0W 1.479,0.885 1.917,1.083 0.438,0.198 10 false 4 2.552,0.865 2.99,1.063 0.438,0.198 10 false 2 1.667,1.146 2.104,1.333 0.438,0.188 10 false AM2 2.177,1.146 2.615,1.333 0.438,0.188 10 false ST2 6.156,0.969 6.594,1.156 0.438,0.188 10 false NSW 6.177,3.281 6.615,3.469 0.438,0.188 10 false STA 5.938,3.188 6.375,3.385 0.438,0.198 10 false 7 5.948,0.854 6.385,1.052 0.438,0.198 10 false 6 3.427,3.885 4.521,4.104 1.094,0.219 10 false ST NO. 1 1.333,3.458 2.427,3.677 1.094,0.219 10 false ST NO. 1 3.177,4.313 3.615,4.51 0.438,0.198 10 false 1 3.188,3.5 3.625,3.698 0.438,0.198 10 false 2 2.552,4.323 2.99,4.521 0.438,0.198 10 false 3 2.573,3.5 3.01,3.698 0.438,0.198 10 false 5 2.583,5.208 2.917,5.396 0.333,0.188 10 false C26 1.583,5.844 1.917,6.031 0.333,0.188 10 false D3 4.438,5.031 6.438,5.24 2,0.208 10 false *1: for Automatic Transmission 4.448,5.354 6.448,5.563 2,0.208 10 false *2: for Manual Transmission 2.583,4.99 3.021,5.188 0.438,0.198 10 false 1 1.615,5.646 2.052,5.844 0.438,0.198 10 false 1 2.156,6.313 3.25,6.531 1.094,0.219 10 false Starter 0.708,6.438 1.802,6.656 1.094,0.219 10 false Battery 5.5,1.865 5.656,2.063 0.156,0.198 10 false B 5.51,2.229 5.667,2.427 0.156,0.198 10 false L 2.75,5.396 3.063,5.594 0.313,0.198 10 false ST 1.885,5.708 2.042,5.906 0.156,0.198 10 false B

w/ Smart Entry and Start System
A358198E03
4.771,1.542 6.115,1.906 1.344,0.365 10 false Park/Neutral Position Switch Assembly*1 2.677,1.656 4,1.875 1.323,0.219 10 false Clutch Start Switch*2 2.688,1.479 3,1.708 0.313,0.229 10 false B2 4.771,1.365 5.083,1.594 0.313,0.229 10 false C22 1.031,0.469 1.344,0.698 0.313,0.229 10 false G16 1.031,0.906 1.344,1.135 0.313,0.229 10 false G17 1.031,2.438 1.344,2.667 0.313,0.229 10 false G17 0.708,0.469 1.021,0.698 0.313,0.229 10 false NE 0.656,2.448 1.042,2.656 0.385,0.208 10 false STA 0.563,0.906 1.031,1.115 0.469,0.208 10 false STAR 6.167,0.458 6.635,0.667 0.469,0.208 10 false NEO 6.146,0.906 6.615,1.115 0.469,0.208 10 false NSW 6.167,2.448 6.635,2.656 0.469,0.208 10 false STA 6.271,3.406 6.74,3.615 0.469,0.208 10 false ECM 6.271,3.219 6.74,3.427 0.469,0.208 10 false G130 1.115,0.281 1.427,0.51 0.313,0.229 10 false 6 1.083,2.25 1.396,2.479 0.313,0.229 10 false 37 1.073,0.719 1.385,0.948 0.313,0.229 10 false 16 5.875,0.375 6.188,0.604 0.313,0.229 10 false 17 5.958,0.823 6.271,1.052 0.313,0.229 10 false 6 4.365,1.26 4.677,1.49 0.313,0.229 10 false 4 4.365,2.042 4.677,2.271 0.313,0.229 10 false 5 2.292,2.052 2.604,2.281 0.313,0.229 10 false 1 2.292,1.24 2.604,1.469 0.313,0.229 10 false 2 5.958,2.333 6.271,2.563 0.313,0.229 10 false 7 3.948,3.115 4.26,3.344 0.313,0.229 10 false 5 4.563,3.115 4.875,3.344 0.313,0.229 10 false 2 4.563,3.927 4.875,4.156 0.313,0.229 10 false 1 3.958,3.927 4.271,4.156 0.313,0.229 10 false 3 0.167,3.198 1.292,3.844 1.125,0.646 10 false Certification ECU (Smart Key ECU Assembly) 2.656,3.125 3.375,3.344 0.719,0.219 10 false ST NO. 1 4.813,3.51 5.531,3.729 0.719,0.219 10 false ST NO. 1 3.563,5.802 4.281,6.021 0.719,0.219 10 false Starter 2.979,5.323 3.698,5.542 0.719,0.219 10 false D3 3.969,4.688 4.688,4.906 0.719,0.219 10 false C26 1.969,4.26 3.073,4.479 1.104,0.219 10 false FL MAIN 3.0W 2.083,5.906 2.802,6.125 0.719,0.219 10 false Battery 3.969,4.5 4.281,4.729 0.313,0.229 10 false 1 3.01,5.135 3.323,5.365 0.313,0.229 10 false 1 4.958,4.875 7.031,5.083 2.073,0.208 10 false *1: for Automatic Transmission 4.958,5.219 7.031,5.427 2.073,0.208 10 false *2: for Manual Transmission 4.115,4.885 4.427,5.083 0.313,0.198 10 false ST 3.271,5.24 3.427,5.438 0.156,0.198 10 false B 4.396,1.427 4.552,1.625 0.156,0.198 10 false B 4.406,1.833 4.563,2.031 0.156,0.198 10 false L

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF - A
ON w/ Smart Entry and Start System for Automatic Transmission B
for Manual Transmission C
w/o Smart Entry and Start System for Automatic Transmission D
for Manual Transmission E




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

7.INSPECT CLUTCH START SWITCH

D

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

E

15.INSPECT CLUTCH START SWITCH
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

6.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

B

END

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

Result:
Proceed to
OK
NG



OK

NG

REPAIR SMART ENTRY AND START SYSTEM

6.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)
7.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

8.REPLACE CLUTCH START SWITCH
8.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)
9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

13.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1KD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

14.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
11.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

B

END

13.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
14.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>1KD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
15.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

16.REPLACE CLUTCH START SWITCH
16.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)