Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER
RM33K0E _51 Engine / Hybrid System _043579 1KD-FTV INTAKE / EXHAUST _0222126 EXHAUST MANIFOLD W/ TURBOCHARGER A

1KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the injector assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of turbocharger sub-assembly


Perform initialization - (Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17940D 3.REMOVE INTERCOOLER ASSEMBLY

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53735B 7.REMOVE FRONT FENDER APRON SEAL UPPER

a.

Remove the 5 clips and front fender apron seal upper.


Hide 53882F 8.REMOVE FRONT FENDER SEAL

a.

Remove the 5 clips and front fender seal.


Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17705 10.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.
A344947

Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.


b.
A344948

Detach the 4 clips.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.


Hide 17801 11.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.
A345134

Remove the air cleaner element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 12.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A344949

Disconnect the 3 wire harness clamps.


b.
A344950

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 12229 13.REMOVE PCV PIPE

a.
A211832

Remove the bolt and disconnect the 2 PCV hoses and PCV pipe from the cylinder head sub-assembly and compressor inlet elbow.


Hide 17274 14.REMOVE COMPRESSOR INLET ELBOW

a.
A211833

Disconnect the 2 connectors from the turbocharger sub-assembly.


b.

Detach the wire harness clamp from the compressor inlet elbow.


c.

Remove the 2 nuts, compressor inlet elbow and gasket from the turbocharger sub-assembly.


Hide 17271 15.REMOVE NO. 1 TURBO INSULATOR

a.
A255740

Remove the 2 bolts and No. 1 turbo insulator from the turbocharger sub-assembly.


Hide 17167 16.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A255741

Remove the bolt and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 16284 17.REMOVE NO. 1 TURBO WATER HOSE

a.
A211835

Remove the 2 No. 1 turbo water hoses from the No. 3 water by-pass pipe and cylinder block sub-assembly.


Hide 17291 18.REMOVE TURBINE OUTLET ELBOW

a.
A211836

Remove the 3 nuts, turbine outlet elbow and gasket from the turbocharger sub-assembly.


Hide 17293 19.REMOVE TURBOCHARGER STAY

a.
A211837

Remove the 2 bolts, nut and turbocharger stay from the turbocharger sub-assembly and cylinder block sub-assembly.


Hide 15407 20.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A301790N01
0.938,0.948 1.219,1.198 0.281,0.25 10 false A

Remove the 2 bolts, 2 nuts and 2 gaskets from the turbocharger sub-assembly and cylinder block sub-assembly.

NOTICE:

Do not loosen the nut labeled A.



b.

Remove the union bolt and turbo oil inlet pipe sub-assembly from the turbocharger sub-assembly and cylinder block sub-assembly.


Hide 17201 21.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A211839

Remove the 3 nuts and turbocharger sub-assembly.


b.

Remove the gasket.


Hide 17141 22.REMOVE EXHAUST MANIFOLD

a.
A252010

Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.


b.

Remove the gasket.


Hide 16027 23.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A211906

Remove the 2 bolt, nuts, No. 1 turbo water pipe sub-assembly and gasket from the turbocharger sub-assembly.