84820
1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD)
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (w/ Smart Entry and Start System)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (w/o Jam Protection Function)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Lock |
| *b | Unlock |
| *c | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
Measure the resistance according to the value(s) in the table below. (w/o Smart Entry and Start System)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (L) - 1 (E) | Lock switch pushed | Below 1 Ω |
| 2 (L) - 1 (E) | Lock switch not pushed | 10 kΩ or higher |
| 8 (UL) - 1 (E) | Unlock switch pushed | Below 1 Ω |
| 8 (UL) - 1 (E) | Unlock switch not pushed | 10 kΩ or higher |
If the result is not as specified, replace the power window regulator master switch assembly.
84820
2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD)
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (w/ Smart Entry and Start System)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
| *b | LED Illumination |
Check that the LED illuminates. (w/o Jam Protection Function)
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Battery connection | Result |
|---|---|
| Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Lock |
| *b | Unlock |
| *c | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
Measure the resistance according to the value(s) in the table below. (w/o Smart Entry and Start System)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (L) - 9 (E) | Lock switch pushed | Below 1 Ω |
| 8 (L) - 9 (E) | Lock switch not pushed | 10 kΩ or higher |
| 2 (UL) - 9 (E) | Unlock switch pushed | Below 1 Ω |
| 2 (UL) - 9 (E) | Unlock switch not pushed | 10 kΩ or higher |
If the result is not as specified, replace the power window regulator master switch assembly.