Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0222452 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 69318C 1.INSTALL DOOR LOCK WIRING HARNESS SEAL

NOTICE:
·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly LH.

·

When reusing a removed front door lock assembly LH, replace the door lock wiring harness seal with a new one.



a.
B438879C01
0,0 0,0 false
V113147

Install in this Direction


Install a new door lock wiring harness seal to the front door lock assembly LH.


Hide 69720B 2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B438881C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front door lock remote control cable assembly LH to the front door lock assembly LH.


Hide 69760C 3.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B438880C02
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front door inside locking cable assembly LH to the front door lock assembly LH.


Hide 69036A 4.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH

a.
B438875

Attach the clamp and claw to install the front door lock cover sub-assembly LH.


Hide 69320 5.INSTALL FRONT DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door lock assembly LH.


b.
B438882C01
1.125,0.427 1.406,0.427 1.406,0.427 1.729,0.844 true 0.948,0.354 1.26,0.552 0.313,0.198 10 true *1
*1 Front Door Lock Open Rod LH
V113147

Install in this Direction


Connect the front door lock open rod LH to install the front door lock assembly LH as shown in the illustration.

HINT:

Make sure that the front door lock open rod LH is securely connected to the front door lock assembly LH.



c.
B438873C02
0,0 0,0 false
V100135

"Torx" Screw
V100136

Connector


Using a T30 "TORX" socket wrench, install the front door lock assembly LH with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 6.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 67404F 7.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

Hide 68102 8.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 68151C 9.INSTALL FRONT DOOR GLASS RUN LH

Hide 67832 10.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 67602 11.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284C 12.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 13.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 14.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 74220 15.INSTALL FRONT ARMREST ASSEMBLY LH

Hide 67492A 16.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 18.CHECK SRS WARNING LIGHT (w/ Curtain Shield Airbag)