Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0222453 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69340 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.
B340417C06
1.292,3.594 0.917,3.594 true 2.156,3.615 2.521,3.615 true 1.479,3.865 1.479,4.177 true 1.979,3.875 1.979,4.198 true 2.083,2.094 2.396,2.292 0.313,0.198 10 false *a 1.615,2.292 2,2.49 0.385,0.198 10 false *b 0.833,2.917 1.146,3.115 0.313,0.198 10 false *c 0.802,3.51 0.958,3.708 0.156,0.198 10 false L 2.583,3.531 2.896,3.729 0.313,0.198 10 false UL 1.438,4.229 1.594,4.427 0.156,0.198 10 false E 1.823,4.219 2.438,4.417 0.615,0.198 10 false LSSR
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly LH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly LH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.



Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.
B340416C06
1.271,3.594 0.917,3.594 true 2.177,3.594 2.5,3.594 true 2.021,3.885 2.104,4.198 true 1.438,3.875 1.323,4.208 true 1.063,2.104 1.375,2.302 0.313,0.198 10 false *a 1.615,2.323 1.927,2.521 0.313,0.198 10 false *b 0.75,2.865 1.063,3.063 0.313,0.198 10 false *c 0.802,3.531 0.958,3.729 0.156,0.198 10 false L 2.563,3.521 2.875,3.719 0.313,0.198 10 false UL 1.979,4.24 2.594,4.438 0.615,0.198 10 false LSSR 1.281,4.24 1.438,4.438 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly RH.



b.

Check the resistance of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.