Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222679 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C160258C07
0.441,0.3 0.653,0.503 0.212,0.203 10 *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU (Brake actuator assembly) ground
3 (GL1) Deceleration sensor signal input
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 (EXI2)* L4 detection switch (Transfer shift actuator assembly) input
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
15 (GGND) Deceleration sensor ground
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
22 (SP1) Speed signal output for speedometer
24 (+BM) Motor relay power supply
25 (CANH) CAN communication line H
26 (VGS) Deceleration sensor power supply
28 (STP) Stop light switch input
31 (EXI)* A.D.D. position switch (Differential motor actuator assembly) input
32 (TS) Signal check input
34 (IG1) Skid control ECU (Brake actuator assembly) power supply

*: for 4WD



TERMINAL INSPECTION


a.

Disconnect the A3 connector and measure the voltage or resistance on the wire harness side.

C160261C13
3.406,0.656 3.75,0.865 0.344,0.208 0.563,0.396 0.875,0.594 0.313,0.198 10 false *a 3.49,0.677 3.958,0.917 0.469,0.24 10 false A3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A3-1 (GND1) - Body ground W-B - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A3-8 (EXI2) - Body ground* G - Body ground L4 detection switch (Transfer shift actuator assembly) input
·

Ignition switch ON

·

4WD control switch (Transfer position switch) not set to L4


11 to 14 V
A3-12 (+BS) - Body ground B - Body ground Solenoid relay power supply Always 11 to 14 V
A3-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A3-24 (+BM) - Body ground R - Body ground Motor relay power supply Always 11 to 14 V
A3-28 (STP) - Body ground G - Body ground Stop light switch input Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V
A3-31 (EXI) - Body ground* L - Body ground A.D.D. position switch (Differential motor actuator assembly) signal input
·

Ignition switch ON

·

4WD control switch (Transfer position switch) set to H2


11 to 14 V
A3-34 (IG1) - Body ground L - Body ground Skid control ECU (Brake actuator assembly) power supply Ignition switch ON 11 to 14 V

*: for 4WD