Power is supplied to the radio and display receiver assembly and steering pad switch assembly when the light control switch is in the tail or head position.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or other components (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except radio and display receiver assembly. | B |
| No illumination comes on (radio and display receiver assembly, steering pad switch, hazard switch, heater control switch, etc.). | C |
A
B
C
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly or Spiral Cable Sub-assembly) |
Disconnect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.
*1: w/ VSC
*2: w/o VSC
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G4-13 (IL+2) - Body ground | Light control switch in tail or head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ VSC
*2: w/o VSC
Remove the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG (w/ VSC) |
| NG (w/o VSC) |
OK
NG (w/ VSC)
NG (w/o VSC)
Disconnect the G100 radio and display receiver assembly connector.
Disconnect the G4 spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.
*1: w/ VSC
*2: w/o VSC
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-23 (SWG) - G4-3 (EAU) | Always | Below 1 Ω |
| G100-23 (SWG) or G4-3 (EAU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G102-10 (ILL+) - Body ground | Light control switch in tail or head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G103 radio and display receiver assembly connector.
for TFT Display Type:
Disconnect the G9 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-5 (ILL-) - G9-21 (ILL-) | Always | Below 1 Ω |
| G103-5 (ILL-) or G9-21 (ILL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-5 (ILL-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG