Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID(w/o VSC) › 2015.11–2016.07
RM33K0E _54 Brake _043534 BRAKE SYSTEM (OTHER) _0223425 BRAKE FLUID(w/o VSC) N

BRAKE SYSTEM (OTHER)  BRAKE FLUID(w/o VSC)  BLEEDING  


CAUTION / NOTICE / HINT

HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed air from the brake system.


NOTICE:
·

for Manual Transmission:

Move the shift lever to neutral and apply the parking brake before bleeding the brakes.

·

for Automatic Transmission:

Move the shift lever to P and apply the parking brake before bleeding the brakes.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

When bleeding air, select the suitable procedure listed below.

Replaced/Installed Item Work Procedure
Flexible hose (front/rear) Bleed brake line
Front disc brake cylinder assembly
Rear wheel cylinder assembly
Brake actuator assembly Bleed brake system
Brake master cylinder sub-assembly
Brake master cylinder reservoir assembly
Brake booster assembly



PROCEDURE

Hide 1.BLEED BRAKE LINE

a.

Remove the brake master cylinder reservoir filler cap assembly.


b.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT 3


NOTICE:

Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



c.

Loosen the bleeder plug of the front disc brake cylinder RH.


d.

Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the front disc brake cylinder RH.

NOTICE:

Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.



e.

After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


f.

Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.


g.

Loosen the bleeder plug of the rear wheel brake cylinder RH.


h.

Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the rear wheel brake cylinder RH.

NOTICE:

Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.



i.

After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

Torque:
for Rear Drum Brake : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for Rear Disc Brake : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)


j.

Bleed the air from the bleeder plug of the rear wheel brake cylinder LH using the same procedure as for the RH side.


k.

Inspect for brake fluid leaks.


l.

Inspect brake fluid level in reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID(w/o VSC)>ON-VEHICLE INSPECTION



Hide 2.BLEED BRAKE SYSTEM

NOTICE:

Be sure to clean your hands before bleeding from the master cylinder to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.


a.

Bleed the brake master cylinder.

i.

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT 3


NOTICE:

Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



iii.

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




iv.

Slowly depress and hold the brake pedal.*1

C326957C01
0.333,0.115 0.531,0.271 0.198,0.156 10 false *A 2.635,0.104 2.854,0.281 0.219,0.177 10 false *B
*A for LHD *B for RHD



v.

Block the outer holes with your fingers, and release the pedal.*2

C326958C01
0.49,0.094 0.708,0.271 0.219,0.177 10 false *A 2.594,0.104 2.792,0.281 0.198,0.177 10 false *B
*A for LHD *B for RHD



vi.

Repeat steps *1 and *2, 3 or 4 times.


vii.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)





b.

Bleed the brake line.

i.

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake fluid:

SAE J1703 or FMVSS No. 116 DOT 3


NOTICE:

Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



iii.

Loosen the bleeder plug of the front disc brake cylinder RH.


iv.

Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the front disc brake cylinder RH.

NOTICE:

Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.



v.

After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


vi.

Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.


vii.

Loosen the bleeder plug of the rear disc brake cylinder RH.


viii.

Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the rear wheel brake cylinder RH.

NOTICE:

Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.



ix.

After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

Torque:
for Rear Drum Brake : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for Rear Disc Brake : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)


x.

Bleed the air from the bleeder plug of the rear wheel brake cylinder LH using the same procedure as for the RH side.



c.

Inspect for brake fluid leaks.


d.

Inspect brake fluid level in reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID(w/o VSC)>ON-VEHICLE INSPECTION