Home › Brake › BRAKE (FRONT) › FRONT DISC BRAKE PAD
RM33K0E _54 Brake _043535 BRAKE (FRONT) _0223434 FRONT DISC BRAKE PAD A

BRAKE (FRONT)  FRONT DISC BRAKE PAD  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



NOTICE:

After replacing the disc brake pads, the clearance between the disc brake pads and front discs becomes larger and the brake pedal feel becomes softer. Therefore, after replacing the disc brake pads, depress the brake pedal several times and check the clearance and brake pedal feel.


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 04947 3.REMOVE FRONT DISC BRAKE ANTI-RATTLE SPRING

a.
C326951C02
1.104,0.458 0.792,0.458 true 1.313,2.031 0.938,1.719 0.938,1.719 0.76,1.719 true 2.438,1.698 2.729,1.698 false 2.313,0.208 2.594,0.208 true 2.177,0.969 2.677,0.969 true 0.531,0.396 0.76,0.563 0.229,0.167 10 true *1 2.792,1.625 3.01,1.802 0.219,0.177 10 false *2 2.708,0.896 2.906,1.083 0.198,0.188 10 true *3 2.635,0.115 2.854,0.292 0.219,0.177 10 true *2 0.49,1.656 0.719,1.823 0.229,0.167 10 true *1
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips and 2 disc brake pad guide pin.


b.

Remove the front disc brake anti-rattle spring.

NOTICE:

The front disc brake anti-rattle spring can be reused if it has sufficient rebound; nodeformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.



Hide 04465 4.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the disc brake cylinder assembly LH.


Hide 04945 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 front No. 1 anti-squeal shims from each pad.


Hide 04945 6.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.

Install the 2 front No. 1 anti-squeal shims to the each pad.

NOTICE:

When replacing worn front disc brake pads, the anti-squeal shims must be replaced together with the front disc brake pads.



Hide 04465 7.INSTALL FRONT DISC BRAKE PAD

a.
C323347C01
2,1.719 2,1.917 2,1.917 1.792,1.917 false 1.469,1.844 1.802,2.031 0.333,0.188 10 false SST
V113147

Expand


Using SST, push back the front disc brake piston.

NOTICE:

Do not forcibly install the piston into the disc brake cylinder assembly LH.


SST
09719-77020  


b.

Install the 2 front disc brake pads to the disc brake cylinder assembly LH.

NOTICE:

Make sure there is no oil or grease on the friction surface of the front disc brake pads and front disc.



Hide 04947 8.INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.


b.

Install the 2 pin hold clips.

NOTICE:

When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.



c.

Depress the brake pedal several times.


Hide 10.INSTALL FRONT WHEEL