Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM
RM33K0E _53 Suspension _043532 TIRE / WHEEL _0223543 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Specified Pressure (When Tire is Cool):
Tire Size Unloaded Loaded
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
265/65R17 112S 200 (2.0, 29) 200 (2.0, 29) 200 (2.0, 29) 200 (2.0, 29)
265/60R18 110H 200 (2.0, 29) 200 (2.0, 29) 200 (2.0, 29) 200 (2.0, 29)



b.
C137874

Using a dial indicator, check the runout of the tires.

Tire runout:

3.0 mm (0.1181 in.) or less


HINT:

Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.



Hide 2.ROTATE TIRES

C237752C01
0.52,0.449 0.692,0.608 0.172,0.159 10 *a 0.52,2.168 0.692,2.326 0.172,0.159 10 *a 1.816,1.923 1.987,2.082 0.172,0.159 10 *c 1.807,0.185 1.979,0.343 0.172,0.159 10 *b
*a Front of the Vehicle
*b Vehicle Wheels and Spare Tire Wheel are Same Type
*c Vehicle Wheels are Aluminum but Spare Tire Wheel is Steel


a.

Remove the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>REMOVAL


b.

Rotate the tires as shown in the illustration.


c.

Install the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>INSTALLATION


Hide 3.INSPECT WHEEL BALANCE

a.
C264658N01
2.098,3.633 2.240,3.803 0.142,0.170 10 A

for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Tire Size Standard Imbalance after Adjustment
265/65R17 112S 13 g (0.028 lb) or less
265/60R18 110H 12 g (0.026 lb) or less

NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the sticking surface of the tape.

·

Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight firmly to adhere it to the position.

·

Do not reuse the balance weight.

·

Please use the Toyota genuine sticking type balance weight.



HINT:
·

The inner side balance weights should be installed by clipping them to the rim.

·

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.




b.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Standard Imbalance after Adjustment:

13 g (0.028 lb) or less


HINT:

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on the-car balancing as necessary.



Hide 4.INSPECT FRONT AXLE HUB BEARING LOOSENESS