When the trigger switch is pressed, the certification ECU (smart key control ECU assembly) generates a request signal and sends it through the front door outside handle assembly (for Driver Door) (electrical key antenna).
The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the driver side door in order to detect the person carrying the electrical key transmitter sub-assembly.
DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Driver Door) (between terminals CLG5 and ANT1, or terminals CG5B and ANT2).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B27A1 | Open in Driver Side Electrical Antenna Circuit | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Driver Door) (CLG5 - ANT1, CG5B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*). | ·
Harness or connector ·
Front door outside handle assembly (for Driver Door) ·
Certification ECU (smart key ECU assembly) |
DTC Output Confirmation Operation:
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Entry lock/unlock operation cannot be performed for driver door | - |
| DTC No. | Data List and Active Test |
|---|---|
| B27A1 | Key diagnostic mode can be used to perform troubleshooting |
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Driver Door).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the K8*1 or J7*2 front door outside handle assembly (for Driver Door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-9 (CLG5) - K8-3 (ANT1) | Always | Below 1 Ω |
| G17-25 (CG5B) - K8-6 (ANT2) | Always | Below 1 Ω |
| G17-9 (CLG5) or K8-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G17-25 (CG5B) or K8-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-9 (CLG5) - J7-3 (ANT1) | Always | Below 1 Ω |
| G17-25 (CG5B) - J7-6 (ANT2) | Always | Below 1 Ω |
| G17-9 (CLG5) or J7-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G17-25 (CG5B) or J7-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G17 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-10 (E) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Trigger switch ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G17-9 (CLG5) - G16-10 (E) | Procedure:
1.
Engine switch off 2.
All doors closed |
- | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door). |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
|
| G17-25 (CG5B) - G16-10 (E) | Procedure:
1.
Engine switch off 2.
All doors closed |
- | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door). |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front door outside handle assembly (for Driver Door) with a new one or the front door outside handle assembly (for Front Passenger Door) if it is functioning properly.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B27A1 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG