If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front door outside handle assembly (for front passenger door). If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Front Passenger Door)), or there may be wave interference.
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).
While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
w/ Door control Battery:
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
w/ Automatic Light Control System:
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If the front passenger door entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
| Tester Display |
|---|
| Operation History |
| Parameter Name | Cause of Problem and Countermeasure |
|---|---|
| Lock / Key RF Signal Interference | When entry lock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry lock operation has been successfully performed, the possibility of wave interference is high. |
| Unlock / Key RF Signal Interference | When entry unlock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry unlock operation has been successfully performed, the possibility of wave interference is high. |
When the door control switch on the power window master switch is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the DTCs.
DTC B27A2 is not output.
| Result | Proceed to |
|---|---|
| DTC B27A2 is not output. | A |
| DTC B27A2 is output. | B |
A
B
| *A | for LHD |
| *a | Approximately 0.3m (0.984 ft.) |
| *A | for RHD |
| *a | Approximately 0.3m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for Front Passenger Door) and perform an entry function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally. | A |
| Entry function operates normally. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Door Trigger Switch | Front passenger door trigger switch | ON or OFF | ON: Front passenger door trigger switch pressed
OFF: Front passenger door trigger switch not pressed |
·
Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| P-Door Trigger Switch |
On the GTS screen, the display changes between ON and OFF as shown in the table above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *A | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the front door outside handle assembly (for Front Passenger Door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Front Passenger Door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the J7*1 or K8*2 front door outside handle assembly (for Front Passenger Door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-26 (CLG6) - J7-3 (ANT1) | Always | Below 1 Ω |
| G17-27 (CG6B) - J7-6 (ANT2) | Always | Below 1 Ω |
| G17-26 (CLG6) or J7-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G17-27 (CG6B) or J7-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-26 (CLG6) - K8-3 (ANT1) | Always | Below 1 Ω |
| G17-27 (CG6B) - K8-6 (ANT2) | Always | Below 1 Ω |
| G17-26 (CLG6) or K8-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G17-27 (CG6B) or K8-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the J7*1 or K8*2 front door outside handle assembly (for Front Passenger Door) connector.
*1: for LHD
*2: for RHD
Connect the G17 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-10 (E) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Trigger switch ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G17-26 (CLG6) - G16-10 (E) | Procedure:
1.
Engine switch off 2.
All doors closed |
- | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door). |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
|
| G17-27 (CG6B) - G16-10 (E) | Procedure:
1.
Engine switch off 2.
All doors closed |
- | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door). |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7*1 or K8*2 front door outside handle assembly (for Front Passenger Door) connector.
*1: for LHD
*2: for RHD
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-1 (TRG+) - G16-12 (TSW2) | Always | Below 1 Ω |
| J7-4 (TRG-) - Body ground | Always | Below 1 Ω |
| J7-1 (TRG+) or G16-12 (TSW2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K8-1 (TRG+) - G16-12 (TSW2) | Always | Below 1 Ω |
| K8-4 (TRG-) - Body ground | Always | Below 1 Ω |
| K8-1 (TRG+) or G16-12 (TSW2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door outside handle assembly (for Front Passenger Door).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL
Inspect the front door outside handle assembly (for Front Passenger Door).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the operation of the entry lock/unlock function.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly (for Front Passenger Door) before performing the inspection.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG