Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224642 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

The system unsets if these ID codes match. Thus, the certification ECU (smart key ECU assembly) and the ECM communicate with each other enabling the engine to start.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR



HINT:

When the ECM and certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the ECM and certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.INSPECT ECM (TERMINAL IMI AND IMO)

C

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK (for 2TR-FE)
OK (for 1GR-FE)
NG



OK (for 2TR-FE)

OK (for 1GR-FE)

NG

3.CHECK WHETHER ENGINE STARTS
3.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT ECM (TERMINAL IMI AND IMO)
4.INSPECT ECM (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

for Gasoline:
B413963C02
0.927,0.073 1.323,0.302 0.396,0.229 2.115,0.063 2.51,0.292 0.396,0.229 3.344,0.052 3.74,0.281 0.396,0.229 4.656,0.052 5.052,0.281 0.396,0.229 5.802,0.063 6.198,0.292 0.396,0.229 1.313,1.448 1.708,1.677 0.396,0.229 2.677,1.448 3.073,1.677 0.396,0.229 4.219,1.469 4.615,1.698 0.396,0.229 5.469,1.458 5.865,1.688 0.396,0.229 1.406,2.969 1.802,3.198 0.396,0.229 2.146,2.969 2.542,3.198 0.396,0.229 3.146,2.969 3.542,3.198 0.396,0.229 3.885,2.969 4.281,3.198 0.396,0.229 4.594,2.958 4.99,3.188 0.396,0.229 5.354,2.958 5.75,3.188 0.396,0.229 2.5,6.01 2.906,6.01 2.906,6.01 2.906,5.844 true 2.896,8.031 3.302,8.031 3.302,8.031 3.302,7.865 true 4.948,0.833 5.031,1.427 5.031,1.427 5.188,1.427 true 5.052,0.792 5.229,0.177 5.229,0.177 5.396,0.177 true 4.5,2.26 4.583,2.854 4.583,2.854 4.74,2.854 true 4.625,2.229 4.802,1.615 4.802,1.615 4.969,1.615 true 2.458,3.583 2.656,3.094 2.656,3.094 2.823,3.094 true 2.229,3.615 2.344,4.344 2.344,4.344 2.5,4.344 true 0.99,0.104 1.448,0.302 0.458,0.198 10 false C14 4.719,0.094 5.177,0.292 0.458,0.198 10 false G56 5.885,0.094 6.344,0.292 0.458,0.198 10 false G57 0.052,0.042 0.51,0.24 0.458,0.198 12 false *A 0.063,1.458 0.521,1.656 0.458,0.198 12 false *B 0.073,2.958 0.531,3.156 0.458,0.198 12 false *C 0.063,0.24 0.521,0.438 0.458,0.198 10 false *a 0.073,1.667 0.531,1.865 0.458,0.198 10 false *a 0.094,3.146 0.552,3.344 0.458,0.198 10 false *a 1.448,3.01 1.906,3.208 0.458,0.198 10 false G158 2.177,3 2.635,3.198 0.458,0.198 10 false G159 3.198,3 3.656,3.198 0.458,0.198 10 false C120 3.927,3.01 4.385,3.208 0.458,0.198 10 false C119 4.635,3 5.094,3.198 0.458,0.198 10 false C118 5.396,3 5.854,3.198 0.458,0.198 10 false C117 0.875,5.802 1.333,6 0.458,0.198 10 false GND 0.906,7.813 1.365,8.01 0.458,0.198 10 false GND 1,4.542 1.458,4.74 0.458,0.198 10 false *1 1.042,6.521 1.5,6.719 0.458,0.198 10 false *2 1.625,8.427 2.083,8.625 0.458,0.198 10 false *3 2.948,4.823 3.406,5.021 0.458,0.198 10 false *4 2.302,6.792 2.76,6.99 0.458,0.198 10 false *3 3.333,6.781 3.792,6.979 0.458,0.198 10 false *5 2.333,5.917 2.792,6.115 0.458,0.198 10 false *b 3.031,5.917 3.49,6.115 0.458,0.198 10 false *c 2.708,7.948 3.167,8.146 0.458,0.198 10 false *b 3.438,7.927 3.896,8.125 0.458,0.198 10 false *c 2.479,9.25 2.938,9.448 0.458,0.198 10 false *d 4.469,9.25 4.927,9.448 0.458,0.198 10 false *d 2.542,9.531 3,9.729 0.458,0.198 10 false *e 4.385,9.521 4.844,9.719 0.458,0.198 10 false *e 3.583,9.042 4.042,9.24 0.458,0.198 10 false or 5.229,1.344 5.688,1.542 0.458,0.198 10 false IMI 5.448,0.104 5.906,0.302 0.458,0.198 10 false IMO 4.771,2.781 5.229,2.979 0.458,0.198 10 false IMI 5.021,1.531 5.479,1.729 0.458,0.198 10 false IMO 2.854,3.021 3.313,3.219 0.458,0.198 10 false IMO 2.563,4.281 3.021,4.479 0.458,0.198 10 false IMI 2.177,0.104 2.635,0.302 0.458,0.198 10 false C15 3.417,0.094 3.875,0.292 0.458,0.198 10 false C16 1.417,1.51 1.875,1.708 0.458,0.198 10 false C14 2.74,1.5 3.198,1.698 0.458,0.198 10 false C15 4.313,1.51 4.771,1.708 0.458,0.198 10 false G56 5.542,1.51 6,1.708 0.458,0.198 10 false G57
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


for Diesel:
B413964C02
1.469,0.552 1.896,0.781 0.427,0.229 4.135,0.542 4.563,0.771 0.427,0.229 5.313,0.531 5.74,0.76 0.427,0.229 2.76,0.531 3.188,0.76 0.427,0.229 0.781,2.563 1.208,2.792 0.427,0.229 1.844,2.573 2.271,2.802 0.427,0.229 3.906,2.583 4.333,2.813 0.427,0.229 4.99,2.583 5.417,2.813 0.427,0.229 2.948,2.573 3.375,2.802 0.427,0.229 6.01,2.573 6.438,2.802 0.427,0.229 3,8.073 3.302,8.073 3.302,8.073 3.302,7.865 true 2.594,6.052 2.896,6.052 2.896,6.052 2.896,5.844 true 5.438,3.906 5.625,3.906 5.625,3.906 5.792,3.26 true 6.281,3.906 6.073,3.906 6.073,3.906 5.948,3.271 true 4.333,2.073 4.521,2.073 4.521,2.073 4.625,1.635 true 5.01,2.063 4.802,2.063 4.802,2.063 4.708,1.635 true 5.146,3.823 5.615,4.125 0.469,0.302 10 false IMO 0.115,0.292 0.427,0.49 0.313,0.198 10 false *a 0.115,0.125 0.427,0.323 0.313,0.198 12 false *A 0.146,2.469 0.458,2.667 0.313,0.198 12 false *B 0.156,2.635 0.469,2.833 0.313,0.198 10 false *a 1.573,0.594 1.885,0.792 0.313,0.198 10 false C73 4.208,0.583 4.635,0.771 0.427,0.188 10 false G129 5.375,0.573 5.875,0.76 0.5,0.188 10 false G130 0.865,2.615 1.177,2.813 0.313,0.198 10 false C38 1.938,2.615 2.25,2.813 0.313,0.198 10 false C39 3.031,2.615 3.344,2.813 0.313,0.198 10 false C40 4,2.615 4.313,2.813 0.313,0.198 10 false C41 5.073,2.615 5.385,2.813 0.313,0.198 10 false G49 6.083,2.625 6.396,2.823 0.313,0.198 10 false G50 2.865,0.573 3.177,0.771 0.313,0.198 10 false C74 1.052,4.427 1.365,4.625 0.313,0.198 10 false *1 0.865,5.802 1.396,6 0.531,0.198 10 false GND 0.927,7.813 1.458,8.01 0.531,0.198 10 false GND 1.073,6.51 1.385,6.708 0.313,0.198 10 false *2 1.802,8.375 2.135,8.615 0.333,0.24 10 false *3 2.24,6.792 2.573,7.031 0.333,0.24 10 false *3 3.333,6.792 3.667,7.031 0.333,0.24 10 false *5 2.948,4.833 3.281,5.073 0.333,0.24 10 false *4 3.031,5.927 3.365,6.167 0.333,0.24 10 false *c 3.417,7.938 3.75,8.177 0.333,0.24 10 false *c 2.438,5.938 2.771,6.177 0.333,0.24 10 false *b 2.833,7.958 3.167,8.198 0.333,0.24 10 false *b 2.458,9.26 2.792,9.5 0.333,0.24 10 false *d 2.521,9.542 2.854,9.781 0.333,0.24 10 false *e 4.375,9.552 4.708,9.792 0.333,0.24 10 false *e 4.448,9.25 4.781,9.49 0.333,0.24 10 false *d 3.552,9.052 3.885,9.292 0.333,0.24 10 false or 6.333,3.823 6.802,4.125 0.469,0.302 10 false IMI 5.063,1.99 5.531,2.292 0.469,0.302 10 false IMO 4.115,1.99 4.583,2.292 0.469,0.302 10 false IMI
*A for 1KD-FTV *B for 1GD-FTV
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
for Gasoline
Item Content
Tester Connection G56-9 (IMO) - Body ground*1
G56-10 (IMI) - Body ground*1
G159-8 (IMO) - Body ground*2
G159-10 (IMI) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

for Diesel
Item Content
Tester Connection G129-29 (IMO) - Body ground*3
G129-30 (IMI) - Body ground*3
G50-17 (IMO) - Body ground*4
G50-16 (IMI) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected


*1: for 2TR-FE

*2: for 1GR-FE

*3: for 1KD-FTV

*4: for 1GD-FTV



Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B
Waveform B not output, or has abnormal wavelength or shape (for 2TR-FE) C
Waveform B not output, or has abnormal wavelength or shape (for 1KD-FTV) D
Waveform B not output, or has abnormal wavelength or shape (for 1GD-FTV) E
Waveform B not output, or has abnormal wavelength or shape (for 1GR-FE) F
Waveform C not output, or has abnormal wavelength or shape G



A

5.REGISTER ECU COMMUNICATION ID

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

D

E

F

G

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G56*1, G129*2, G50*3 or G159*4 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G129-30 (IMI) Always Below 1 Ω
G129-30 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G17-35 (EFIO) - G159-10 (IMI) Always Below 1 Ω
G159-10 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER RECOGNITION CODES
9.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GR-FE) C
NG (for 1KD-FTV) D
NG (for 1GD-FTV) E
NG (for 1GD-FTV (w/ DPF)) F
NG (for 1GD-FTV (for i-ART)) G



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

D

E

F

G