Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2015.11–2016.07
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224643 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B418869E02
4.896,2.833 7.156,3.292 2.26,0.458 10 false G136 4.896,3.01 7.156,3.469 2.26,0.458 10 false Transponder Key ECU Assembly 6.01,0.24 6.417,0.656 0.406,0.417 10 false +B 1.76,1.469 2.167,1.885 0.406,0.417 10 false +B 2,1.781 2.406,2.198 0.406,0.417 10 false IMI 1.979,0.865 2.385,1.281 0.406,0.417 10 false IMO 2.354,1 2.76,1.417 0.406,0.417 10 false G56 2.708,1 3.115,1.417 0.406,0.417 10 false G129 3.146,1 3.552,1.417 0.406,0.417 10 false G50 2.406,2.135 2.813,2.552 0.406,0.417 10 false *1 2.813,2.135 3.219,2.552 0.406,0.417 10 false *2 3.229,2.135 3.635,2.552 0.406,0.417 10 false *3 2.417,1.229 2.823,1.646 0.406,0.417 10 false *1 2.792,1.24 3.198,1.656 0.406,0.417 10 false *2 3.208,1.24 3.615,1.656 0.406,0.417 10 false *3 2.458,0.75 2.875,0.969 0.417,0.219 10 false 9 2.802,0.74 3.219,0.958 0.417,0.219 10 false 29 3.198,0.74 3.615,0.958 0.417,0.219 10 false 17 2.406,1.646 2.823,1.865 0.417,0.219 10 false 10 2.823,1.646 3.24,1.865 0.417,0.219 10 false 30 3.219,1.646 3.635,1.865 0.417,0.219 10 false 16 5.042,1.76 5.552,1.979 0.51,0.219 10 false EFIO 4.75,1.76 5.26,1.979 0.51,0.219 10 false 13 4.76,0.865 5.271,1.083 0.51,0.219 10 false 12 5.042,0.854 5.552,1.073 0.51,0.219 10 false EFII 1.313,2.896 1.823,3.115 0.51,0.219 10 false ECM 2.792,2.833 4.615,3.063 1.823,0.229 10 false *1: for 2TR-FE 2.792,3.083 4.615,3.313 1.823,0.229 10 false *2: for 1KD-FTV 2.802,3.354 4.625,3.583 1.823,0.229 10 false *3: for 1GD-FTV 2.698,1.917 3.104,2.333 0.406,0.417 10 false G129 3.156,1.917 3.563,2.333 0.406,0.417 10 false G50 2.354,1.906 2.76,2.323 0.406,0.417 10 false G56

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT ECM (TERMINAL IMO)

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B433604C01
0.854,0.063 1.333,0.292 0.479,0.229 2.135,0.052 2.615,0.281 0.479,0.229 3.406,0.052 3.885,0.281 0.479,0.229 4.667,0.052 5.146,0.281 0.479,0.229 5.823,0.073 6.302,0.302 0.479,0.229 1.229,1.656 1.708,1.885 0.479,0.229 2.667,1.656 3.146,1.885 0.479,0.229 4.167,1.646 4.646,1.875 0.479,0.229 5.479,1.646 5.958,1.875 0.479,0.229 5.26,3.406 5.74,3.635 0.479,0.229 4.104,3.406 4.583,3.635 0.479,0.229 2.708,3.385 3.188,3.615 0.479,0.229 1.406,3.385 1.885,3.615 0.479,0.229 0.719,5.094 1.198,5.323 0.479,0.229 1.792,5.104 2.271,5.333 0.479,0.229 2.917,5.094 3.396,5.323 0.479,0.229 3.854,5.083 4.333,5.313 0.479,0.229 4.969,5.083 5.448,5.313 0.479,0.229 5.958,5.073 6.438,5.302 0.479,0.229 4.25,4.917 4.49,4.917 4.49,4.917 4.677,4.479 true 4.188,3.229 4.427,3.229 4.427,3.229 4.583,2.542 true 4.677,1.438 4.917,1.438 4.917,1.438 5.042,0.833 true 5.271,6.385 5.51,6.385 5.51,6.385 5.792,5.719 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *A 0.167,1.719 0.479,1.875 0.313,0.156 10 false *B 0.125,3.427 0.438,3.583 0.313,0.156 10 false *C 0.125,5.115 0.438,5.271 0.313,0.156 10 false *D 0.125,5.25 0.438,5.406 0.313,0.156 10 false *a 2.917,8.375 3.229,8.531 0.313,0.156 10 false *b 1,8.26 1.458,8.458 0.458,0.198 10 false GND 4.917,6.292 5.375,6.49 0.458,0.198 10 false IMO 3.938,4.823 4.396,5.021 0.458,0.198 10 false IMO 3.854,3.146 4.313,3.344 0.458,0.198 10 false IMO 4.385,1.344 4.844,1.542 0.458,0.198 10 false IMO 0.958,0.104 1.417,0.302 0.458,0.198 10 false C14 2.25,0.083 2.708,0.281 0.458,0.198 10 false C15 3.552,0.083 4.01,0.281 0.458,0.198 10 false C16 2.76,1.708 3.219,1.906 0.458,0.198 10 false C15 1.333,1.719 1.792,1.917 0.458,0.198 10 false C14 4.792,0.094 5.25,0.292 0.458,0.198 10 false G56 4.281,1.667 4.74,1.865 0.458,0.198 10 false G56 5.583,1.667 6.042,1.865 0.458,0.198 10 false G57 5.969,0.104 6.427,0.302 0.458,0.198 10 false G57 1.552,3.438 2.01,3.635 0.458,0.198 10 false C73 2.802,3.438 3.26,3.635 0.458,0.198 10 false C74 4.167,3.448 4.625,3.646 0.458,0.198 10 false G129 5.365,3.448 5.823,3.646 0.458,0.198 10 false G130 0.833,5.135 1.292,5.333 0.458,0.198 10 false C38 1.906,5.135 2.365,5.333 0.458,0.198 10 false C39 3.01,5.135 3.469,5.333 0.458,0.198 10 false C40 3.99,5.135 4.448,5.333 0.458,0.198 10 false C41 5.021,5.115 5.479,5.313 0.458,0.198 10 false G49 6.073,5.125 6.531,5.323 0.458,0.198 10 false G50
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1KD-FTV *D for 1GD-FTV
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G56-9 (IMO) - Body ground*1
G129-29 (IMO) - Body ground*2
G49-17 (IMO) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV


OK:

Waveform is similar to that shown in the illustration.



Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

4.INSPECT ECM (TERMINAL IMI)

B

10.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

7.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B433605C01
2.135,0.042 2.615,0.313 0.479,0.271 0.906,0.052 1.385,0.323 0.479,0.271 3.385,0.042 3.865,0.313 0.479,0.271 4.656,0.052 5.135,0.323 0.479,0.271 5.802,0.063 6.281,0.333 0.479,0.271 5.469,1.667 5.948,1.938 0.479,0.271 4.219,1.646 4.698,1.917 0.479,0.271 2.656,1.646 3.135,1.917 0.479,0.271 1.281,1.635 1.76,1.906 0.479,0.271 1.427,3.344 1.906,3.615 0.479,0.271 2.688,3.354 3.167,3.625 0.479,0.271 4.094,3.333 4.573,3.604 0.479,0.271 5.281,3.323 5.76,3.594 0.479,0.271 5.948,4.969 6.427,5.24 0.479,0.271 4.927,4.979 5.406,5.25 0.479,0.271 3.854,5.01 4.333,5.281 0.479,0.271 2.875,5 3.354,5.271 0.479,0.271 1.823,5 2.302,5.271 0.479,0.271 0.76,4.99 1.24,5.26 0.479,0.271 4.417,1.427 4.667,1.427 4.667,1.427 4.938,0.833 true 3.958,3.094 4.208,3.094 4.208,3.094 4.479,2.5 true 4.125,4.844 4.375,4.844 4.375,4.844 4.573,4.458 true 5.385,6.375 5.635,6.375 5.635,6.375 5.885,5.75 true 0.115,0.073 0.427,0.229 0.313,0.156 10 false *A 0.219,1.729 0.531,1.885 0.313,0.156 10 false *B 0.24,3.448 0.552,3.604 0.313,0.156 10 false *C 0.146,5.021 0.458,5.177 0.313,0.156 10 false *D 0.156,0.229 0.469,0.385 0.313,0.156 10 false *a 3.313,8.385 3.625,8.542 0.313,0.156 10 false *b 0.219,1.875 0.531,2.031 0.313,0.156 10 false *a 0.25,3.583 0.563,3.74 0.313,0.156 10 false *a 0.156,5.177 0.469,5.333 0.313,0.156 10 false *a 1,0.115 1.313,0.271 0.313,0.156 10 false C14 2.25,0.094 2.563,0.25 0.313,0.156 10 false C15 2.75,1.688 3.063,1.844 0.313,0.156 10 false C15 3.49,0.104 3.802,0.26 0.313,0.156 10 false C16 4.802,0.125 5.115,0.281 0.313,0.156 10 false G56 4.302,1.708 4.615,1.865 0.313,0.156 10 false G56 5.594,1.74 5.906,1.896 0.313,0.156 10 false G57 5.906,0.135 6.219,0.292 0.313,0.156 10 false G57 1.354,1.719 1.667,1.875 0.313,0.156 10 false C14 1.521,3.417 1.833,3.573 0.313,0.156 10 false C73 2.792,3.417 3.104,3.573 0.313,0.156 10 false C74 4.156,3.396 4.604,3.552 0.448,0.156 10 false G129 5.344,3.385 5.792,3.542 0.448,0.156 10 false G130 6.063,5.021 6.375,5.177 0.313,0.156 10 false G50 5.052,5.042 5.365,5.198 0.313,0.156 10 false G49 3.938,5.073 4.25,5.229 0.313,0.156 10 false C41 3.01,5.073 3.323,5.229 0.313,0.156 10 false C40 1.927,5.052 2.24,5.208 0.313,0.156 10 false C39 0.875,5.052 1.188,5.208 0.313,0.156 10 false C38 0.875,8.271 1.427,8.49 0.552,0.219 10 false GND 4.063,1.365 4.375,1.521 0.313,0.156 10 false IMI 3.719,3.042 4.031,3.198 0.313,0.156 10 false IMI 3.865,4.771 4.177,4.927 0.313,0.156 10 false IMI 5.146,6.281 5.458,6.438 0.313,0.156 10 false IMI
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1KD-FTV *D for 1GD-FTV
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G56-10 (IMI) - Body ground*1
G129-30 (IMI) - Body ground*2
G50-16 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID

NG

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ECM
7.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

10.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

B418866C02
1.052,0.229 1.49,0.51 0.438,0.281 3.292,0.229 3.729,0.51 0.438,0.281 5.604,0.25 6.042,0.531 0.438,0.281 6.438,1.396 6.24,2.229 6.24,2.229 6.031,2.229 true 1.094,1.396 1.354,2.24 1.354,2.24 1.542,2.24 true 3.115,1.698 3.271,2.219 3.271,2.219 3.458,2.219 true 1.156,0.292 1.615,0.49 0.458,0.198 10 false G56 3.344,0.281 3.802,0.479 0.458,0.198 10 false G129 5.688,0.313 6.146,0.51 0.458,0.198 10 false G50 0.177,0.094 0.635,0.292 0.458,0.198 12 false *A 2.552,0.073 3.01,0.271 0.458,0.198 12 false *B 4.792,0.104 5.25,0.302 0.458,0.198 12 false *C 0.198,0.292 0.656,0.49 0.458,0.198 10 false *a 2.573,0.271 3.031,0.469 0.458,0.198 10 false *a 4.802,0.281 5.26,0.479 0.458,0.198 10 false *a 1.615,2.167 2.073,2.365 0.458,0.198 10 false IMO 3.521,2.135 3.979,2.333 0.458,0.198 10 false IMO 5.75,2.146 6.208,2.344 0.458,0.198 10 false IMO
*A for 2TR-FE *B for 1KD-FTV
*C for 1GD-FTV - -
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result
G56-9 (IMO) - Body ground*1
G129-29 (IMO) - Body ground*2
G50-17 (IMO) - Body ground*3
Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or Abnormal waveform B



A

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

B

7.REPLACE ECM
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
a.

Disconnect the G136 transponder key ECU assembly connector.


b.

Disconnect the G56*1, G129*2 or G50*3 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G136-12 (EFII) - G56-9 (IMO) Always Below 1 Ω
G136-13 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-9 (IMO) - Body ground Always 10 kΩ or higher
G136-12 (EFII) - Body ground Always 10 kΩ or higher
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G136-12 (EFII) - G129-29 (IMO) Always Below 1 Ω
G136-13 (EFIO) - G129-30 (IMI) Always Below 1 Ω
G129-29 (IMO) - Body ground Always 10 kΩ or higher
G136-12 (EFII) - Body ground Always 10 kΩ or higher
G129-30 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G136-12 (EFII) - G50-17 (IMO) Always Below 1 Ω
G136-13 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-17 (IMO) - Body ground Always 10 kΩ or higher
G136-12 (EFII) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.REGISTER KEY
13.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 1GD-FTV)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 1GD-FTV)