Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2015.11–2016.07
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224643 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B354639E06
3.333,0.583 3.833,0.833 0.5,0.25 3.427,0.625 3.885,0.823 0.458,0.198 10 false G136

a.

Disconnect the G136 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G136-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G136-1 (+B) - G136-5 (GND) Input L - BR Battery Always 11 to 14 V +B
G136-2 (IG) - G136-5 (GND) Input P - BR Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
G136-3 (KSW) - G136-5 (GND) Input G - BR Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G136 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G136-8 (IND) - G136-5 (GND) Output Y - BR Security indicator light signal No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
G136-9 (D) - G136-5 (GND) Input/Output R - BR DLC3 communication Without communication Below 1 V -
During communication Pulse generation
G136-4 (ANT1) - G136-5 (GND) Input/Output Y - BR Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
G136-15 (ANT2) - G136-5 (GND) Input/Output W - BR Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
G136-12 (EFII) - G136-5 (GND) Input Y - BR ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
E/G Start Permission
G136-13 (EFIO) - G136-5 (GND) Output B - BR ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection G136-4 (ANT1) - G136-5 (GND)
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection G136-15 (ANT2) - G136-5 (GND)
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G136-12 (EFII) - G136-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G136-13 (EFIO) - G136-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 2TR-FE)


A347038C08
1,2.167 1.417,2.417 0.417,0.25 2.5,2.167 2.917,2.417 0.417,0.25 4.219,2.167 4.667,2.417 0.448,0.25 5.583,2.167 6,2.417 0.417,0.25 0.698,0.313 1.094,0.583 0.396,0.271 2,0.313 2.448,0.573 0.448,0.26 3.417,0.344 3.865,0.604 0.448,0.26 4.813,0.313 5.26,0.583 0.448,0.271 6.083,0.323 6.563,0.583 0.479,0.26 0.073,0.208 0.385,0.406 0.313,0.198 12 false *A 0.094,2.063 0.406,2.26 0.313,0.198 12 false *B 0.771,0.375 1.229,0.573 0.458,0.198 10 false C14 2.073,0.375 2.531,0.573 0.458,0.198 10 false C15 3.51,0.375 3.969,0.573 0.458,0.198 10 false C16 4.875,0.365 5.333,0.563 0.458,0.198 10 false G56 6.167,0.375 6.625,0.573 0.458,0.198 10 false G57 1.083,2.208 1.542,2.406 0.458,0.198 10 false C14 2.583,2.229 3.042,2.427 0.458,0.198 10 false C15 4.292,2.208 4.75,2.406 0.458,0.198 10 false G56 5.677,2.219 6.135,2.417 0.458,0.198 10 false G57
*A for Automatic Transmission Models *B for Manual Transmission Models


a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C14-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C14-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C14-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C15-5 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C14-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G57-1 (+B) - C14-3 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G57-2 (+B2) - C14-3 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
G57-3 (BATT) - C14-3 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G56-9 (IMO) - C14-3 (E1) Output Y - W-B Transponder key ECU assembly output signal Ignition switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G56-10 (IMI) - C14-3 (E1) Input B - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G56-9 (IMO) - C14-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G56-10 (IMI) - C14-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1KD-FTV)


A254878E08
1.208,0.406 1.615,0.646 0.406,0.24 2.729,0.406 3.135,0.646 0.406,0.24 4.292,0.406 4.698,0.646 0.406,0.24 5.76,0.406 6.167,0.646 0.406,0.24 1.281,0.448 1.594,0.625 0.313,0.177 10 false C73 2.802,0.448 3.115,0.625 0.313,0.177 10 false C74 4.333,0.448 4.792,0.677 0.458,0.229 10 false G129 5.792,0.448 6.271,0.667 0.479,0.219 10 false G130

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C74-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C73-7 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C73-6 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G129-2 (BATT) - C74-1 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G130-1 (+B) - C74-1 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G129-29 (IMO) - C74-1 (E1) Output Y - W-B Transponder key ECU assembly output signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G129-30 (IMI) - C74-1 (E1) Input B - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G129-29 (IMO) - C74-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G129-30 (IMI) - C74-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GD-FTV)


A340466E01
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 1.844,0.469 2.156,0.667 0.313,0.198 10 false C39 0.635,0.469 0.948,0.667 0.313,0.198 10 false C38 2.938,0.469 3.25,0.667 0.313,0.198 10 false C40 3.99,0.469 4.302,0.667 0.313,0.198 10 false C41 5.083,0.469 5.396,0.667 0.313,0.198 10 false G49 6.25,0.469 6.563,0.667 0.313,0.198 10 false G50

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C41-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C41-3 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C40-3 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C41-2 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C41-4 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G50-2 (+B) - C41-1 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G50-3 (+B2) - C41-1 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
G50-1 (BATT) - C41-1 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G50-17 (IMO) - C41-1 (E1) Output Y - W-B Transponder key ECU assembly communication output Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G50-16 (IMI) - C41-1 (E1) Input B - W-B Transponder key ECU assembly communication input Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G50-17 (IMO) - C41-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G50-16 (IMI) - C41-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal