Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › TIMING BELT
RM33K0E _51 Engine / Hybrid System _043569 1KD-FTV ENGINE MECHANICAL _0225042 TIMING BELT G

1KD-FTV ENGINE MECHANICAL  TIMING BELT  INSPECTION  


PROCEDURE

Hide 13568 1.INSPECT TIMING BELT

A054953C07
1.292,0.031 1.49,0.177 0.198,0.146 10 false *a 2.719,0.24 2.917,0.417 0.198,0.177 10 false *c 1.875,0.417 2.073,0.583 0.198,0.167 10 false *b
*a INCORRECT
*b Oil
*c Water


NOTICE:
·

Do not bend or twist the timing belt, and do not turn the timing belt inside out.

·

Do not allow the timing belt to come into contact with oil, water or steam.



a.

Visually inspect the timing belt.

If defects are present, perform the steps below.


b.

If there is premature parting:

i.

Check for proper installation.


ii.

Check the No. 1 timing belt cover gasket for damage and proper installation.



c.

If the timing belt teeth are cracked or damaged, check if either camshaft sub-assembly is locked.


d.

If there is noticeable wear or cracks on the timing belt face, check if there are nicks on the side of the No. 1 timing belt idler pulley sub-assembly.


e.

If there is wear or damage on only one side of the timing belt, check the timing belt guide and the alignment of each pulley.


f.

If there is noticeable wear on the timing belt teeth, check the No. 1 timing belt cover for damage, check that the gasket is installed correctly and check for foreign matter on the pulley teeth.

If necessary, replace the timing belt.


Hide 13505 2.INSPECT NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

a.
A352024

Check that the No. 1 timing belt idler sub-assembly pulley turns smoothly by hand.


b.
A352025

Visually check that the seal portion of the No. 1 timing belt idler sub-assembly pulley has no grease on it.

NOTICE:
·

If there is oil, water or other foreign matter on the timing belt or a pulley, repair the leak.

·

Do not allow the timing belt and each pulley to come into contact with oil, water or steam.

·

Before installing the No. 1 timing belt idler pulley sub-assembly, be sure to clean each pulley with a cloth or equivalent.

·

When inspecting the No. 1 timing belt idler sub-assembly, do not remove it unless absolutely necessary.




Hide 13540 3.INSPECT NO. 1 TIMING BELT TENSIONER ASSEMBLY

a.
A352026

Visually check the seal portion of the No. 1 timing belt tensioner assembly for oil leakage.

If leakage is found, replace the No. 1 timing belt tensioner assembly.

HINT:

A trace of oil on the No. 1 timing belt tensioner push rod side's seal is acceptable.



b.
A352027

Hold the No. 1 timing belt tensioner assembly with both hands as shown in the illustration. Firmly push the push rod and check that it does not move.

If the push rod moves, replace the No. 1 timing belt tensioner assembly.

NOTICE:

Never point the No. 1 timing belt tensioner assembly push rod downward.



c.
A352028C01
2.969,0.375 3.167,0.552 0.198,0.177 10 false *a
*a Protrusion Distance


Measure the protrusion distance of the No. 1 timing belt tensioner assembly push rod from the housing end.

Standard protrusion distance:

8.1 to 8.9 mm (0.319 to 0.350 in.)


If the protrusion distance is not as specified, replace the No. 1 timing belt tensioner assembly.