Home › Engine / Hybrid System › 2TR-FE EMISSION CONTROL › CANISTER
RM33K0E _51 Engine / Hybrid System _043521 2TR-FE EMISSION CONTROL _0225079 CANISTER G

2TR-FE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CANISTER (CHARCOAL CANISTER ASSEMBLY) (for Fuel Tank Cap Method)


b.

Check for clogs in the air filter (when not using the GTS).

i.

Start the engine.


ii.

Warm up the engine.


iii.

Allow the engine to idle for 15 minutes.


iv.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


v.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


vi.
A202994

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




c.

Check for clogs in the air filter (when using the GTS).

i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

v.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


vi.

Perform the Active Test "Activate the VSV for Evap Control" while the engine is idling.


vii.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


viii.

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




Hide 2.INSPECT CANISTER (CHARCOAL CANISTER ASSEMBLY) (for Vacuum Measurement Method)

NOTICE:

When inspecting with parts installed on the vehicle, be sure to remove the fuel tank cap assembly.


a.

Visually check the canister (charcoal canister assembly) for airtightness.

i.

Visually check the canister (charcoal canister assembly) for cracks or damage, and check that there is no gasoline smell.



b.

Inspect the ventilation of the canister (charcoal canister assembly).

i.
A350694C01
2.375,1.146 3.063,1.146 true 1.5,1.188 1.875,1.188 1.875,1.188 2.01,0.896 true 2.583,0.521 2.979,0.333 2.979,0.333 3.146,0.333 true 0.385,1.094 0.656,1.094 false 3.083,1.021 3.281,1.229 0.198,0.208 10 true *a 1.323,1.083 1.521,1.292 0.198,0.208 10 true *b 3.198,0.24 3.396,0.448 0.198,0.208 10 true *c 0.208,0.99 0.396,1.177 0.188,0.188 10 false *d
*a Port (A)
*b Port (B)
*c Port (C)
*d Vacuum Pump


Using a vacuum pump, apply vacuum (1.96 kPa (15 mmHg, 0.579 in. Hg)) to the port (A) with the port (B) and port (C) closed.

OK:

Air does not flow.



ii.
A350695C01
0.375,1.104 0.656,1.104 false 1.406,1.198 1.781,1.198 1.781,1.198 1.99,0.875 true 2.583,0.51 2.938,0.281 2.938,0.281 3.115,0.281 true 2.375,1.135 3.063,1.135 true 3.083,1.01 3.313,1.229 0.229,0.219 10 true *a 1.24,1.104 1.427,1.292 0.188,0.188 10 true *b 3.135,0.177 3.344,0.385 0.208,0.208 10 true *c 0.198,1 0.375,1.198 0.177,0.198 10 false *d
*a Port (A)
*b Port (B)
*c Port (C)
*d Vacuum Pump


Using a vacuum pump, apply vacuum (1.96 kPa (15 mmHg, 0.579 in. Hg)) to the port (A) with the port (C) closed.

OK:

Air is sucked into the port (B).



iii.
A350696C01
1.083,0.313 1.302,0.313 1.302,0.313 1.802,0.573 true 1.635,1.26 2.438,1.26 true 0.833,1.281 1.052,1.281 1.052,1.281 1.229,0.938 true 2.469,1.146 2.677,1.365 0.208,0.219 10 true *a 0.615,1.198 0.802,1.385 0.188,0.188 10 true *b 0.875,0.219 1.063,0.417 0.188,0.198 10 true *c 1.25,1.927 1.479,2.115 0.229,0.188 10 true *d
*a Port (A)
*b Port (B)
*c Port (C)
*d Air


Close the port (C) and apply compressed air (4.41 kPa (0.04 kgf/cm2, 0.6 psi)) to the port (A).

OK:

Air flows out from the port (B).



iv.
A350697C01
0.781,1.25 1.021,1.25 1.021,1.25 1.25,0.938 true 1.104,0.375 1.323,0.375 1.323,0.375 1.781,0.573 true 1.625,1.25 2.427,1.25 true 2.448,1.146 2.698,1.375 0.25,0.229 10 true *a 0.604,1.135 0.813,1.344 0.208,0.208 10 true *b 0.917,0.281 1.135,0.479 0.219,0.198 10 true *c 1.24,1.917 1.438,2.104 0.198,0.188 10 true *d
*a Port (A)
*b Port (B)
*c Port (C)
*d Air


Apply compressed air (4.41 kPa (0.04 kgf/cm2, 0.6 psi)) to the port (A).

OK:

Air flows out from the port (B) and port (C).



v.

Engage the 2 claws and install the cap to the canister (charcoal canister assembly).



c.
A350698C01
2.531,1.063 2.729,1.458 2.729,1.458 2.875,1.458 true 0.375,0.323 0.635,0.323 false 0.635,1.646 0.854,1.646 0.854,1.646 1,1.292 true 1.458,1.646 1.458,1.177 true 2.094,1.698 2.094,1.396 true 0.427,1.563 0.615,1.771 0.188,0.208 10 true *1 2.917,1.354 3.135,1.563 0.219,0.208 10 true *a 1.385,1.667 1.594,1.875 0.208,0.208 10 true *b 2.021,1.708 2.229,1.927 0.208,0.219 10 true *c 0.198,0.219 0.406,0.406 0.208,0.188 10 false *d
*1 Fuel Tank to Canister Tube
*a Port (A)
*b 3-way Connector
*c Hose
*d Vacuum Pump


Check for clogs in the air filter (when not using the GTS).

i.

Connect the fuel tank to canister tube to the canister (charcoal canister assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Start the engine.


iii.

Warm up the engine.


iv.

Allow the engine to idle for 15 minutes.


v.

Check the indicator needle of the vacuum pump.

OK:

The indicator needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.




d.
A350699C01
0.375,0.313 0.635,0.313 false 0.719,1.615 0.854,1.615 0.854,1.615 0.979,1.281 true 2.094,1.75 2.094,1.406 true 2.542,1.083 2.792,1.479 2.792,1.479 2.927,1.479 true 1.458,1.615 1.458,1.167 true 0.51,1.521 0.708,1.708 0.198,0.188 10 true *1 2.938,1.354 3.146,1.573 0.208,0.219 10 true *a 1.396,1.635 1.594,1.823 0.198,0.188 10 true *b 2.01,1.76 2.198,1.958 0.188,0.198 10 true *c 0.188,0.208 0.375,0.406 0.188,0.198 10 false *d
*1 Fuel Tank to Canister Tube
*a Port (A)
*b 3-way Connector
*c Hose
*d Vacuum Pump


Check for clogs in the air filter (when using the GTS).

i.

Connect the fuel tank to canister tube to the canister (charcoal canister assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

vi.

Perform the Active Test "Activate the VSV for Evap Control" while the engine is idling.


vii.

Check the indicator needle of the vacuum pump.

OK:

The indicator needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.