Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM33K0E _51 Engine / Hybrid System _043519 1GR-FE ENGINE MECHANICAL _0225346 REAR CRANKSHAFT OIL SEAL A

1GR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.

Apply MP grease to the lip of a new rear crankshaft oil seal.


b.
A326592C03
1.125,2.031 1.26,2.031 1.26,2.031 1.26,1.24 true 0.833,1.948 1.219,2.156 0.385,0.208 10 false SST 2.229,1.188 2.615,1.396 0.385,0.208 10 false *a
*a -0.5 (-0.0197 in.) to 0.5 mm (0.0197 in.)


Using SST and a hammer, tap in the rear crankshaft oil seal until its surface is flush with the rear oil seal retainer edge.

SST
09223-78010  

Standard:

-0.5 (-0.0197 in.) to 0.5 mm (0.0197 in.) (from the rear oil seal retainer edge)


NOTICE:
·

Keep the lip of the rear crankshaft oil seal free from foreign matter.

·

Do not tap the rear crankshaft oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A344569N01
1.323,0.563 1.323,0.198 1.323,0.198 2.417,0.198 true 1.729,0.563 1.729,0.208 true 2.448,0.135 2.813,0.323 0.365,0.188 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A294918C02
2.563,0.99 2.396,0.99 false 1.719,1 1.552,1 false 0.938,0.99 0.771,0.99 false 0.573,0.917 0.771,1.104 0.198,0.188 10 false *1 1.354,0.917 1.552,1.115 0.198,0.198 10 false *2 2.208,0.917 2.375,1.094 0.167,0.177 10 false *3 2.76,0.76 2.927,0.938 0.167,0.177 10 false *a
*1 Front Drive Plate Spacer
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
*a Automatic Transmission Side


Install the front drive plate spacer, the drive plate and ring gear sub-assembly, and the rear drive plate spacer to the crankshaft.

HINT:

As the front drive plate spacer, the drive plate and ring gear sub-assembly, and the rear drive plate spacer are not reversible, be sure to install them in the direction shown in the illustration.



c.

Clean the bolts and bolt holes.


d.
A192239C99
1.573,0.76 1.677,0.76 1.677,0.76 1.833,1.188 false 1.375,0.677 1.573,0.833 0.198,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A277149N01
1.677,0.208 1.833,0.406 0.156,0.198 10 1 2.292,0.448 2.448,0.646 0.156,0.198 10 5 2.438,0.99 2.594,1.188 0.156,0.198 10 3 2.219,1.573 2.375,1.771 0.156,0.198 10 7 1.646,1.708 1.802,1.906 0.156,0.198 10 2 1.052,1.531 1.208,1.729 0.156,0.198 10 6 0.844,0.969 1.0,1.167 0.156,0.198 10 4 1.083,0.406 1.24,0.604 0.156,0.198 10 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate.