Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL TANK
RM33K0E _51 Engine / Hybrid System _043520 2TR-FE FUEL _0225680 FUEL TANK A

2TR-FE FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77641A 5.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A339621

Remove the 5 nuts and No. 1 fuel tank protector from fuel tank assembly.


Hide 77289B 6.REMOVE NO. 3 FUEL TUBE CLAMP

a.
A349996

Detach the 3 claw and remove the No. 3 fuel tube clamp from the fuel tube.


Hide 77251B 7.DISCONNECT FUEL TUBE

a.
A349997

Disconnect the fuel tank main tube sub-assembly, fuel tank return tube and vent line tube.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 8.DISCONNECT FUEL TANK BREATHER HOSE

a.
A349992

Slide the clamp and disconnect the fuel tank breather hose from the fuel tank filler pipe sub-assembly.


Hide 77213B 9.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A349994

Loosen the clamp and disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe sub-assembly.


Hide 10.REMOVE FUEL TANK ASSEMBLY

a.

Using an engine lifter and attachments, support the fuel tank assembly.


b.
A346239

Remove the 3 bolts and disconnect the 3 fuel tank bands.


c.

Remove the 3 clips, 3 fuel tank band pins and 3 fuel tank bands.

HINT:

Move the fuel tank just enough to remove the pins.



d.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wire harness.



e.
A349998C01
1.927,3.25 2.281,3.25 false 1.167,4.104 1.708,4.104 true 2,3.802 2.146,4.052 2.146,4.052 2.333,4.052 false 2.323,3.177 2.531,3.344 0.208,0.167 10 false *1 0.979,4.031 1.156,4.229 0.177,0.198 10 false *2 2.365,3.969 2.563,4.156 0.198,0.188 10 false *3
*1 Fuel Tank Cushion
*2 Wire Harness
*3 Fuel Tank Assembly


Fold back approximately half of each fuel tank cushion so that the wire harness can be removed in the step below.


f.
A346215

Disconnect the clamp and connector.


g.
A361061

Detach the wire harness from the 6 clamps shown in the illustration.


h.

Disconnect the fuel sender gauge assembly connector from the fuel suction with pump and gauge tube assembly.


Hide 77697 11.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.

Remove the 2 nuts.


b.
A350000C01
0.719,2.167 0.854,2.344 0.135,0.177 10 false 1 1.677,2.167 1.813,2.333 0.135,0.167 10 false 2 2.615,2.167 2.75,2.333 0.135,0.167 10 false 3
V100135

No. 2 Fuel Tank Bracket
V100136

Nut


Using needle-nose pliers, remove the 4 No. 2 fuel tank brackets shown in the illustration, and then remove the No. 1 fuel tank heat insulator.


Hide 12.REMOVE FUEL TANK CUSHION

a.
A350001C01
0.531,0.344 3,0.344 3,0.344 3,0.833 true 2.271,0.792 2.271,0.354 true 0.979,0.917 0.979,0.354 true 0.333,0.271 0.531,0.438 0.198,0.167 10 false *1
*1 Fuel Tank Cushion


Remove the 3 fuel tank cushions from the fuel tank assembly.


Hide 77020A 13.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77213B 14.REMOVE FUEL TANK TO FILLER PIPE HOSE

A350002

a.

Loosen the clamp and remove the fuel tank to filler pipe hose from the fuel tank assembly.