Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0226114 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

Refer to DTC P0016.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>P0016

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) Output voltage of camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC Stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC Stored

HINT:

If DTC P0342 or P0343 is stored, the following symptoms may appear:

·

Difficulty starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0342 Ignition switch ON for 4 seconds or more
P0343

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record any output DTC(s).

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

f.

Turn the ignition switch off for 30 seconds or more.


g.

Disconnect the camshaft position sensor connector.


h.

Turn the ignition switch to ON for 4 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Check whether the DTC changes when the connector is disconnected and connected.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)

B

5.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)
a.
A368773C15
1.76,0.813 2.156,1.083 0.396,0.271 1.833,2.26 2.125,1.646 true 2.469,2.271 2.167,1.646 true 1.854,0.875 2.313,1.073 0.458,0.198 10 false C41 1.406,2.365 2.094,2.583 0.688,0.219 10 false 18 (G2-) 2.26,2.375 3.146,2.615 0.885,0.24 10 false 17 (VCG) 0.146,0.188 0.604,0.385 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C41-17 (VCG) - C41-18 (G2-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C43-1 (G22+) - C41-27 (G2+) Always Below 1 Ω
C43-2 (G22-) - C41-18 (G2-) Always Below 1 Ω
C43-1 (G22+) or C41-27 (G2+) - Body ground and other terminals Always 10 kΩ or higher
C43-2 (G22-) or C41-18 (G2-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the camshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the camshaft position sensor connector.


b.
A186169C12
0.271,1.5 0.667,1.75 0.396,0.25 2.354,2.99 1.99,2.229 true 1.167,2.969 1.5,2.25 true 1.708,2.99 1.698,2.25 true 0.156,0.156 0.375,0.396 0.219,0.24 10 false *a 0.323,1.542 0.688,1.729 0.365,0.188 10 false C43 2.302,3.021 2.667,3.208 0.365,0.188 10 false VC 0.823,3 1.458,3.208 0.635,0.208 10 false G22+ 1.542,3.01 2.177,3.219 0.635,0.208 10 false G22-
*a Front view of wire harness connector
(to Camshaft Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C43-3 (VC) - C43-1 (G22+) Ignition switch off No short or open circuit
C43-1 (G22+) - C43-2 (G22-) Ignition switch off No short or open circuit



c.

Reconnect the camshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

7.REPLACE ECM
5.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END