Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT(for Rear Disc Brake)
RM33K0E _52 Drivetrain _043595 AXLE AND DIFFERENTIAL _0226844 REAR AXLE SHAFT(for Rear Disc Brake) A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT(for Rear Disc Brake)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42312A 1.INSTALL REAR AXLE SHAFT BEARING LH

a.
C328772N01
2.646,0.813 2.813,0.51 2.813,0.51 2.979,0.51 true 3.063,0.438 3.427,0.688 0.365,0.25 10 false SST

Using SST and a press, press in a new rear axle shaft bearing LH.

SST
09950-60020  (09951-00810)


Hide 42311E 2.INSTALL REAR OUTER AXLE SHAFT OIL SEAL

a.
C330673C01
0.708,1.938 0.542,1.615 0.542,1.615 0.865,1.615 false 0.219,1.531 0.677,1.729 0.458,0.198 10 false SST 1.917,1.146 2.375,1.344 0.458,0.198 10 false *a
*a Clearance


Using SST and a press, tap in a new rear outer axle shaft oil seal.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

Standard clearance:

Less than 0.2 mm (0.007 in.)



Hide 42312E 3.INSTALL REAR AXLE HUB BOLT

a.
C328774C01
2.833,0.167 0.688,0.167 0.688,0.167 0.688,0.333 true 1.531,0.833 1.531,0.167 true 2.427,1.344 2.427,0.167 true 2.906,0.083 3.219,0.281 0.313,0.198 10 false *a
*a Oil Drain Hole


Install a new brake drum oil deflector gasket LH and the brake drum oil deflector LH to the rear axle shaft LH.

HINT:

Align the 3 oil drain holes.



b.

Pass 6 new rear axle hub bolts through the rear axle shaft LH.


c.

Secure the rear axle shaft LH between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



d.
C330674C01
2.667,0.604 2.833,0.604 2.833,0.604 2.885,0.802 false 2.76,1.458 2.927,1.458 2.927,1.458 3.031,1.177 true 2.5,0.51 2.813,0.708 0.313,0.198 10 false *a 2.573,1.375 2.885,1.573 0.313,0.198 10 false *b
*a Plate Washer
*b Nut


Temporarily install a plate washer and nut to each of the 6 rear axle hub bolts as shown in the illustration.


e.

Install the 6 rear axle hub bolts by tightening each nut.


f.

Remove the washer and nut from each rear axle hub bolt.


Hide 47043C 4.INSTALL BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

a.
C328775

Position the backing plate on the bearing case.


b.

Using 2 socket wrenches and a press, press in 4 new backing plate to rear axle housing setting bolts.


Hide 42423B 5.INSTALL REAR INNER AXLE BEARING RETAINER LH

a.

Heat a new rear inner axle bearing retainer LH to approximately 70 to 130°C (158 to 266°F).

CAUTION:

Be careful not to burn yourself when the rear inner axle bearing retainer LH temperature is high.



b.
C328776C01
2.521,0.625 2.667,0.385 2.667,0.385 2.917,0.385 false 2.625,1.458 2.854,1.594 2.854,1.594 2.563,1.583 true 0.958,1.427 1.073,1.531 1.073,1.531 1.156,1.531 false 0.917,1.667 0.75,1.917 0.75,1.917 0.583,1.917 false 2.969,0.313 3.427,0.51 0.458,0.198 10 false SST 2.906,1.531 3.365,1.729 0.458,0.198 10 false SST 1.177,1.448 1.635,1.646 0.458,0.198 10 false *a 0.417,1.833 0.875,2.031 0.458,0.198 10 false *b
*a Tapered Surface
*b Chamfered Surface


Install a new rear axle shaft washer LH, a new rear inner axle bearing retainer LH, the backing plate and the rear axle bearing case LH to the rear axle shaft LH as shown in the illustration.

NOTICE:
·

Install the rear axle shaft washer LH with its tapered surface facing downward.

·

Install the rear inner axle bearing retainer LH with its chamfered surface facing downward.




c.

Using SST and a press, press in the rear axle shaft LH.

SST
09631-12090  
09726-40010  
09951-01100  


d.

Using a snap ring expander, install a new rear axle shaft snap ring LH.