Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT(for Rear Drum Brake)
RM33K0E _52 Drivetrain _043595 AXLE AND DIFFERENTIAL _0226845 REAR AXLE SHAFT(for Rear Drum Brake) A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT(for Rear Drum Brake)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42312 1.REMOVE REAR AXLE SHAFT LH

a.
C190686

Using a snap ring expander, remove the rear axle shaft snap ring LH.


b.
C330784N01
0.958,0.313 1.125,0.313 1.125,0.313 1.344,0.417 false 0.625,0.24 1.083,0.438 0.458,0.198 10 false SST

Install SST to the rear axle bearing case LH with the 4 nuts.

SST
09521-25012  


c.
C190688N04
2.542,0.552 2.302,0.552 2.302,0.552 2.042,1.323 true 2.615,0.469 3.094,0.896 0.479,0.427 10 false SST

Using SST and a press, press out the rear axle shaft LH.

SST
09521-25012  

NOTICE:

Be careful not to drop the rear axle shaft LH.


HINT:

If the rear axle shaft bearing LH (inner) remains on the rear axle shaft LH, grind the retainer surface using a grinder, and then pry off the retainer with a chisel and hammer.



d.

Remove the 4 nuts and SST.


e.

Remove the rear inner axle bearing retainer LH and rear axle shaft washer LH from the rear axle shaft bearing LH.


Hide 47043C 2.REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

a.
C328770

Temporarily install 4 nuts to the 4 backing plate to rear axle housing setting bolts.

NOTICE:

Do not use any nuts removed from the vehicle, as they may be damaged.



b.

Using a hammer, tap out the 4 backing plate to rear axle housing setting bolts from the backing plate.


c.

Remove the 4 nuts from the 4 backing plate to rear axle housing setting bolts.


d.

Remove the rear axle bearing case LH from the backing plate.


Hide 42312E 3.REMOVE REAR AXLE HUB BOLT

a.

Secure the rear axle shaft LH between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.
C191008N03
2.156,0.313 1.917,0.313 1.917,0.313 1.802,0.5 false 2.229,0.24 2.625,0.563 0.396,0.323 10 false SST

Using SST, remove the 6 rear axle hub bolts.

SST
09650-17011  


c.

Remove the brake drum oil deflector LH and brake drum oil deflector gasket LH from the rear axle shaft LH.

NOTICE:
·

Do not deform the brake drum oil deflector LH.

·

Make sure to align the groove of SST with the flange of the brake drum oil deflector LH.




Hide 42311E 4.REMOVE REAR OUTER AXLE SHAFT OIL SEAL

a.

Secure the rear axle bearing case LH between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.
C325064N01
2.563,1.792 2.823,1.635 false 2.906,1.531 3.323,1.76 0.417,0.229 10 false SST

Using SST, tap out the rear outer axle shaft oil seal.

SST
09308-00010  

NOTICE:

Be careful not to damage the rear axle bearing case LH.



Hide 42312A 5.REMOVE REAR AXLE SHAFT BEARING LH

a.
C325065N01
2.656,1.385 2.865,1.198 false 1.844,3 2.417,2.26 false 2.938,1.115 3.396,1.313 0.458,0.198 10 false SST 1.542,3 2,3.198 0.458,0.198 10 false SST

Using SST and a press, press out the rear axle shaft bearing LH.

SST
09223-56010  
09950-60020  (09951-00680)