Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM33K0E _53 Suspension _043530 FRONT SUSPENSION _0226847 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48132 1.INSTALL FRONT COIL SPRING LH

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

For SST with stopper pins:

i.

Secure SST in a vise.

SST
09727-00061  
09727-30022  (09727-00010, 09727-00031)


ii.
C302414C01
2.563,1.885 2.198,1.656 false 2.563,2.052 2.563,1.885 2.563,1.885 2.875,1.615 false 2.49,4.354 2.49,4.198 2.49,4.198 2.865,3.958 false 2.5,4.198 2.115,3.958 false 1.583,0.26 1.896,0.417 0.313,0.156 10 false *a 1.615,2.573 1.927,2.729 0.313,0.156 10 false *b 2.5,2.063 2.813,2.219 0.313,0.156 10 false *c 2.417,4.365 2.729,4.521 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.
C302415C01
1.469,1.469 1.469,1.01 false 3.135,1.479 3.135,1.021 false 0.219,0.063 0.531,0.219 0.313,0.156 10 false *a 1.76,0.073 2.073,0.229 0.313,0.156 10 false *b 1.406,1.479 1.719,1.635 0.313,0.156 10 false *c 3.073,1.49 3.385,1.646 0.313,0.156 10 false *c
*a Correct
*b Incorrect
*c Stopper Pin


Install the stopper pins to the hooks of SST.

CAUTION:

Make sure that the stopper pins are installed securely.



iv.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.

·
C322803N02
0.656,1.521 1.323,1.521 true 0.333,1.438 0.792,1.635 0.458,0.198 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure. In this case, installing the coil spring stopper belt as shown in the illustration is recommended.



SST
09727-00110  



b.
C288500N06
2.406,1.26 2.406,0.969 2.406,0.969 2.667,0.969 false 2.698,0.896 3.156,1.094 0.458,0.198 10 false SST

For SST without stopper pins:

i.

Secure SST in a vise.

SST
09727-00060  
09727-30021  (09727-00010, 09727-00031)


ii.
C302414C01
2.563,1.885 2.198,1.656 false 2.563,2.052 2.563,1.885 2.563,1.885 2.875,1.615 false 2.49,4.354 2.49,4.198 2.49,4.198 2.865,3.958 false 2.5,4.198 2.115,3.958 false 1.583,0.26 1.896,0.417 0.313,0.156 10 false *a 1.615,2.573 1.927,2.729 0.313,0.156 10 false *b 2.5,2.063 2.813,2.219 0.313,0.156 10 false *c 2.417,4.365 2.729,4.521 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.



HINT:
C322804N01
0.688,1.521 1.354,1.521 true 0.365,1.438 0.823,1.635 0.458,0.198 10 false SST

Installing SST as shown in the illustration is recommended.


SST
09727-00110  



c.
C322806C01
0,0 0,0 false
V100135

Recess


Install the coil spring to the shock absorber. Fit the lower end of the coil spring into the recess of the spring lower seat.


Hide 48609 2.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the front shock absorber cushion retainer to the front shock absorber assembly LH.


b.

Install the front suspension support sub-assembly LH to the front shock absorber assembly LH.


Hide 48510J 3.INSTALL FRONT NO. 1 SHOCK ABSORBER CUSHION

a.

Install the front No. 1 shock absorber cushion to the front shock absorber assembly LH.


Hide 48510Q 4.INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER

a.

Install the front shock absorber cushion retainer to the front shock absorber assembly LH.


Hide 48680A 5.INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C113160C05
0.938,1.438 0.938,1.771 false 2.333,1.125 2.333,1.792 false 1.635,0.146 1.875,0.313 0.24,0.167 10 false *b 2.76,0.135 3.01,0.333 0.25,0.198 10 false *c 0.844,1.802 1.135,1.99 0.292,0.188 10 false *1 2.281,1.823 2.531,1.99 0.25,0.167 10 false *2 0.385,0.177 0.615,0.385 0.229,0.208 10 false *a
*1 Front Suspension Support Sub-assembly
*2 Absorber Bush
*a for LH
*b Front of the Vehicle
*c for RH


Align the front suspension support sub-assembly and absorber bush as shown in the illustration.


b.
C323462C01
1.74,2.344 2.052,2.542 0.313,0.198 10 false *a 1.208,2.958 1.521,3.156 0.313,0.198 10 false *b 1.073,0.844 1.385,1.042 0.313,0.198 10 false *c
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Using a ball joint lock nut wrench, install a new lock nut.

Torque:
Specified tightening torque : 18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 12 N*m (122 kgf*cm, 9 ft.*lbf)




c.

Release the coil spring while checking the position of the spring lower seat and suspension support.


Hide 6.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C330034C01
1.427,3.948 1.76,3.948 false 0.583,3.958 0.833,3.958 0.833,3.958 0.917,4.208 false 2.073,2.667 2.385,2.865 0.313,0.198 10 false *a 1.833,3.854 2.146,4.052 0.313,0.198 10 false *c 0.385,3.865 0.698,4.063 0.313,0.198 10 false *b
*a Torque Wrench Fulcrum Length
*b 12 x 14 mm Long Offset Wrench
*c 12 mm Socket Hexagon Wrench


Using a 12 mm socket hexagon wrench and 12 x 14 mm long offset wrench, install the 3 nuts to the upper side of the front shock absorber with coil spring.

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a long offset wrench (fulcrum length of 206.25 mm (8.1201 in.)) + torque wrench (fulcrum length of 380 mm (14.9606 in.)): 25.9 N*m (264 kgf*cm, 19 ft.*lbf)




Hide 7.INSTALL FRONT LOWER SUSPENSION ARM

Hide 48811 8.INSTALL FRONT STABILIZER BAR

Hide 9.INSTALL FRONT WHEEL

Hide 10.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Press down on the vehicle several times to stabilize the suspension.


Hide 11.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 4866A 12.INSTALL FRONT LOWER ARM SHAFT BOOT PROTECTOR LH (w/ Drive Shaft Boot Protector)

Hide 13.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 14.PERFORM INITIALIZATION (w/ Automatic Headlight Beam Level Control System)

Hide 15.INSPECT AUTOMATIC LIGHT CONTROL SYSTEM (w/ Automatic Headlight Beam Level Control System)

Hide 16.INSPECT HEADLIGHT AIMING (w/ Automatic Headlight Beam Level Control System)