Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM33K0E _52 Drivetrain _043594 DRIVE SHAFT / PROPELLER SHAFT _0226978 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502K 1.INSTALL FRONT AXLE HUB DUST SEAL

a.
C218303

Using a brass bar and hammer, tap on the front drive outboard joint assembly until a new front axle hub dust seal contacts the edge of the front drive outboard joint assembly.

NOTICE:
·

Do not damage the front axle hub dust seal.

·

The front axle hub dust seal should be installed completely.

·

Make sure to install the front axle hub dust seal in the correct direction.




Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C330811N01
1.083,0.667 1.229,0.229 1.229,0.229 1.396,0.229 true 1.375,1.75 1.542,1.75 1.542,1.75 2.208,1 true 1.458,0.167 1.917,0.365 0.458,0.198 10 false SST 1.052,1.667 1.51,1.865 0.458,0.198 10 false SST

Using SST and a press, press in a new front drive shaft dust cover until the inboard joint contacts the edge of the inboard joint.

SST
09527-10011  
09316-20011  

NOTICE:
·

Do not damage the front drive shaft dust cover.

·

The front drive shaft dust cover should be installed completely.

·

Make sure to install the front drive shaft dust cover in the correct direction.




Hide 3.INSTALL OUTBOARD JOINT BOOT

C127681C05
2.094,0.479 1.896,0.479 1.896,0.479 1.76,0.75 false 2.146,0.406 2.833,0.573 0.688,0.167 10 false *a
*a Protective Tape


a.

Before installing the outboard joint boot, wrap the splines of the front drive outboard joint assembly with protective tape to prevent the outboard joint boot from being damaged.


b.
C307711C01
1.667,1.5 1.667,1.75 true 2.063,1.438 2.063,1.688 true 2.99,1.229 2.99,1.479 true 0.583,1.198 0.583,1.448 true 0.542,1.479 0.854,1.677 0.313,0.198 10 false *4 2.938,1.542 3.25,1.74 0.313,0.198 10 false *3 1.615,1.802 1.927,2 0.313,0.198 10 false *1 2.031,1.729 2.344,1.927 0.313,0.198 10 false *2
*1 Front No. 2 Axle Outboard Joint Boot Clamp
*2 Outboard Joint Boot
*3 Front Axle Outboard Joint Boot Clamp
*4 Front Drive Outboard Joint Assembly
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint assembly in the following order.

i.

Front No. 2 axle outboard joint boot clamp


ii.

Outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Install the outboard joint boot so that it is between the front No. 2 axle outboard joint boot clamp and front drive outboard joint assembly.


d.

Temporarily install the front axle outboard joint boot clamp to the outboard joint boot.


e.

Pack the front drive outboard joint assembly and outboard joint boot with grease from the boot kit.

Standard grease capacity:

268.0 to 288.0 g (9.46 to 10.15 oz)



f.

Install the outboard joint boot to the groove of the front drive outboard joint assembly.

NOTICE:
·

Do not apply grease to the part of the outboard joint boot that contacts the groove.

·

Do not allow foreign matter to enter the outboard joint boot.




Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

a.

Install SST to the front No. 2 axle outboard joint boot clamp LH, and then while pressing the outboard joint boot, slightly tighten the SST bolt.

SST
09521-24010  

NOTICE:
·

Correctly set the front No. 2 axle outboard joint boot clamp LH to the guide groove.

·

Do not damage the outboard joint boot.




b.
C106164C02
0.906,0.469 1.135,0.469 1.135,0.469 1.5,1.073 true 2.719,0.635 3.031,0.833 0.313,0.198 10 false *a 1.49,0.573 1.802,0.771 0.313,0.198 10 false *b 0.542,0.375 0.854,0.573 0.313,0.198 10 false SST
*a Turn
*b Hold


Tighten SST so that the front No. 2 axle outboard joint boot clamp LH is pinched.

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:
·

When tightening SST, make sure the clearance of the front No. 2 axle outboard joint boot clamp LH is within the standard clearance.

·

Do not damage the outboard joint boot.




c.

Remove SST from the front No. 2 axle outboard joint boot clamp LH.


d.
C106165N07
2.031,1.031 2.615,1.552 2.615,1.552 2.792,1.552 true 2.875,1.469 3.292,1.729 0.417,0.26 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp LH.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the front No. 2 axle outboard joint boot clamp LH.



Hide 43447E 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

a.

Install SST to the front axle outboard joint boot clamp LH, and then while pressing the outboard joint boot, slightly tighten the SST bolt.

SST
09521-24010  

NOTICE:
·

Correctly set the front axle outboard joint boot clamp LH to the guide groove.

·

Do not damage the outboard joint boot.




b.
C317892C01
1.167,0.583 1.333,0.583 1.333,0.583 2.083,1.083 true 0.792,0.5 1.333,0.75 0.542,0.25 10 false SST 2.854,1.75 3.167,1.948 0.313,0.198 10 false *a 1.604,0.219 1.917,0.417 0.313,0.198 10 false *b
*a Turn
*b Hold


Tighten SST so that the front axle outboard joint boot clamp LH is pinched.

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:
·

When tightening SST, make sure the clearance of the front axle outboard joint boot clamp LH is within the standard clearance.

·

Do not damage the outboard joint boot.




c.

Remove SST from the front axle outboard joint boot clamp LH.


d.
C207920N01
2.583,1.833 2.417,1.833 2.417,1.833 2.167,1.25 true 2.667,1.75 3.125,1.948 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp LH.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the front axle outboard joint boot clamp LH.



Hide 6.INSTALL INBOARD JOINT

a.
C307713C01
0.667,1.833 0.667,1.333 false 1.25,1.802 1.25,1.469 false 2.5,1.833 2.5,1.667 false 2.917,1.833 2.917,1.25 false 0.625,1.885 0.938,2.083 0.313,0.198 10 false *1 1.188,1.854 1.5,2.052 0.313,0.198 10 false *2 2.448,1.885 2.76,2.083 0.313,0.198 10 false *3 2.844,1.896 3.156,2.094 0.313,0.198 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint assembly in the following order.

i.

Front axle inboard joint boot clamp


ii.

Inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Remove the protective tape from the front drive outboard joint assembly.


c.
C317902C01
0.875,1.542 2.469,1.688 2.469,1.688 1.479,1.188 true 2.583,1.625 2.896,1.823 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and place the beveled side of the tripod joint axial spline toward the front drive outboard joint assembly.


d.
C104525

Using a brass bar and hammer, tap the tripod onto the outboard joint.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod in the correct direction.




e.
C160822

Using a snap ring expander, install a new snap ring.

NOTICE:

The snap ring should be installed completely.



f.

Pack the inboard joint and inboard joint boot with grease from the boot kit.

Standard grease capacity:

165.0 to 185.0 g (5.82 to 6.52 oz)



g.
C127646C05
1.833,0.833 1.833,0.25 true 2.167,0.396 2.167,0.25 2.167,0.25 1.417,0.25 true 1.188,0.167 1.5,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the inboard joint to the front drive outboard joint assembly.


Hide 7.INSTALL INBOARD JOINT BOOT

a.

Install the inboard joint boot to the inboard joint.

NOTICE:
·

Do not apply grease to the part of the inboard joint boot that contacts the groove.

·

Do not allow foreign matter to enter the inboard joint boot.




b.
C237735N05
1.5,1.396 1.823,1.646 0.323,0.25 10 false (A)

Check that the inboard joint boot and outboard joint boot are not stretched or contracted when the front drive shaft assembly is at the standard length.

Length (A):

555.9 mm (1.82 ft.)


NOTICE:

Keep the front drive shaft assembly level during inspection.


If the inboard joint boot and outboard joint boot are stretched or contracted, correct them.


Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH

a.

Install SST to the front axle inboard joint boot clamp LH, and then while pressing the inboard joint boot, slightly tighten the SST bolt.

SST
09521-24010  

NOTICE:
·

Correctly set the front axle inboard joint boot clamp LH to the guide groove.

·

Do not damage the inboard joint boot.




b.
C298637C03
0.833,0.417 1,0.417 1,0.417 1.406,0.792 false 2.25,0.042 2.563,0.24 0.313,0.198 10 false *a 1.208,0.104 1.521,0.302 0.313,0.198 10 false *b 0.542,0.375 0.854,0.573 0.313,0.198 10 false SST
*a Turn
*b Hold


Tighten SST so that the front axle inboard joint boot clamp LH is pinched.

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:
·

When tightening SST, make sure the clearance of the front axle inboard joint boot clamp LH is within the standard clearance.

·

Do not damage the inboard joint boot.




c.

Remove SST from the front axle inboard joint boot clamp LH.


d.
D026926N04
1.469,1.167 2.198,1.396 true 2.281,1.365 2.792,1.646 0.51,0.281 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp LH.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the front axle inboard joint boot clamp LH.



Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

a.
C307716C01
0.49,0.75 0.792,0.823 true 0.833,0.76 1.146,0.958 0.313,0.198 10 false *a
*a Claw Engagement


Install the front No. 2 axle inboard joint boot clamp LH to the inboard joint boot.

NOTICE:

Correctly set the front No. 2 axle inboard joint boot clamp LH to the guide groove.



b.

Using needle-nose pliers, hold the front No. 2 axle inboard joint boot clamp LH at the claw engagement.

NOTICE:
·

Do not damage the inboard joint boot.

·

Do not deform the claw engagement of the front No. 2 axle inboard joint boot clamp LH.




Hide 43420 10.INSPECT FRONT DRIVE SHAFT ASSEMBLY LH