Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2015.11–2016.07
RM33K0E _57 Power Source / Network _043546 NETWORKING _0227039 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of ECM

·

ECM ground circuit

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

for 2TR-FE:
C317091E08
5.302,0.656 5.76,0.854 0.458,0.198 10 false G56 5.292,1.917 5.75,2.115 0.458,0.198 10 false G57 5.292,1.167 5.75,1.365 0.458,0.198 10 false G56 5.292,2.469 5.75,2.667 0.458,0.198 10 false G57 5.292,3.021 5.75,3.219 0.458,0.198 10 false G57 5.302,4.125 5.76,4.323 0.458,0.198 10 false G57 5.292,3.573 5.75,3.771 0.458,0.198 10 false G56 5.719,0.49 6.333,0.688 0.615,0.198 10 false CANH 5.708,1.313 6.323,1.51 0.615,0.198 10 false CANL 5.688,1.917 6.302,2.115 0.615,0.198 10 false BATT 5.698,2.448 6.313,2.646 0.615,0.198 10 false +B 5.698,3.01 6.313,3.208 0.615,0.198 10 false +B2 5.677,3.573 6.292,3.771 0.615,0.198 10 false MREL 5.688,4.125 6.302,4.323 0.615,0.198 10 false IGSW 5.698,4.708 6.313,4.906 0.615,0.198 10 false E1 5.313,4.708 5.771,4.906 0.458,0.198 10 false C14 5.333,0.438 5.646,0.635 0.313,0.198 10 false 13 5.344,0.938 5.656,1.135 0.313,0.198 10 false 14 5.385,1.688 5.698,1.885 0.313,0.198 10 false 3 5.375,2.219 5.688,2.417 0.313,0.198 10 false 1 5.385,2.771 5.698,2.969 0.313,0.198 10 false 2 5.385,3.333 5.708,3.531 0.323,0.198 10 false 6 5.375,3.885 5.698,4.083 0.323,0.198 10 false 8 5.396,4.458 5.708,4.656 0.313,0.198 10 false 3 3.656,1.74 4.427,1.938 0.771,0.198 10 false EFI-B 0.792,2.448 2.49,2.833 1.698,0.385 10 false from EFI-MAIN NO.1 Relay 0.938,3.552 2.5,3.885 1.563,0.333 10 false to EFI-MAIN NO.1 Relay 3.531,3.948 4.302,4.146 0.771,0.198 10 false IG2 NO.1 1.667,1.885 2.469,2.229 0.802,0.344 10 false from Battery 0.333,4.083 2.719,4.302 2.385,0.219 10 false from IG2 Relay*1, Ignition Switch*2 1.646,0.51 1.802,0.708 0.156,0.198 10 false 1 1.625,1.021 1.938,1.219 0.313,0.198 10 false 2 0.135,1.375 0.594,1.573 0.458,0.198 10 false G122 0.146,1.531 3.198,1.813 3.052,0.281 10 false No. 2 CAN Junction Connector 5.885,5.281 6.344,5.479 0.458,0.198 10 false ECM 0.271,4.875 2.656,5.094 2.385,0.219 10 false *1: w/ Smart Entry and Start System 0.26,5.198 2.646,5.417 2.385,0.219 10 false *2: w/o Smart Entry and Start System

for 1GR-FE:
C317091E07
5.25,0.635 5.708,0.833 0.458,0.198 10 false G159 5.26,1.896 5.719,2.094 0.458,0.198 10 false G158 5.26,1.156 5.719,1.354 0.458,0.198 10 false G159 5.25,2.448 5.708,2.646 0.458,0.198 10 false G158 5.25,3.01 5.708,3.208 0.458,0.198 10 false G158 5.26,4.104 5.719,4.302 0.458,0.198 10 false G158 5.25,3.552 5.708,3.75 0.458,0.198 10 false G159 5.719,0.49 6.333,0.688 0.615,0.198 10 false CANH 5.708,1.313 6.323,1.51 0.615,0.198 10 false CANL 5.688,1.917 6.302,2.115 0.615,0.198 10 false BATT 5.698,2.448 6.313,2.646 0.615,0.198 10 false +B 5.698,3.01 6.313,3.208 0.615,0.198 10 false +B2 5.677,3.573 6.292,3.771 0.615,0.198 10 false MREL 5.688,4.125 6.302,4.323 0.615,0.198 10 false IGSW 5.677,4.708 6.292,4.906 0.615,0.198 10 false E01 5.271,4.698 5.729,4.896 0.458,0.198 10 false C118 5.333,0.438 5.646,0.635 0.313,0.198 10 false 31 5.344,0.938 5.656,1.135 0.313,0.198 10 false 25 5.344,1.688 5.656,1.885 0.313,0.198 10 false 24 5.344,2.229 5.656,2.427 0.313,0.198 10 false 23 5.344,2.771 5.656,2.969 0.313,0.198 10 false 22 5.344,3.333 5.667,3.531 0.323,0.198 10 false 36 5.344,3.885 5.667,4.083 0.323,0.198 10 false 21 5.365,4.51 5.677,4.708 0.313,0.198 10 false 23 3.656,1.74 4.427,1.938 0.771,0.198 10 false EFI-B 0.792,2.448 2.49,2.833 1.698,0.385 10 false from EFI-MAIN NO.1 Relay 0.938,3.552 2.5,3.885 1.563,0.333 10 false to EFI-MAIN NO.1 Relay 3.531,3.948 4.302,4.146 0.771,0.198 10 false IG2 NO.1 1.667,1.885 2.469,2.229 0.802,0.344 10 false from Battery 0.313,4.073 2.906,4.271 2.594,0.198 10 false from IG2 Relay*1, Ignition Switch*2 1.646,0.51 1.802,0.708 0.156,0.198 10 false 1 1.625,1.021 1.938,1.219 0.313,0.198 10 false 2 0.135,1.375 0.594,1.573 0.458,0.198 10 false G122 0.146,1.531 3.198,1.813 3.052,0.281 10 false No. 2 CAN Junction Connector 5.885,5.281 6.344,5.479 0.458,0.198 10 false ECM 0.229,4.906 2.823,5.104 2.594,0.198 10 false *1: w/ Smart Entry and Start System 0.219,5.229 2.813,5.427 2.594,0.198 10 false *2: w/o Smart Entry and Start System

for 1KD-FTV:
C329268E03
5.719,0.604 6.333,0.802 0.615,0.198 10 false CANH 5.698,1.354 6.313,1.552 0.615,0.198 10 false CANL 5.688,1.979 6.302,2.177 0.615,0.198 10 false BATT 5.708,2.531 6.323,2.729 0.615,0.198 10 false +B 5.677,3.104 6.292,3.302 0.615,0.198 10 false MREL 5.688,3.583 6.302,3.781 0.615,0.198 10 false IGSW 5.708,4.135 6.323,4.333 0.615,0.198 10 false E1 5.708,4.646 6.323,4.844 0.615,0.198 10 false E01 5.708,5.135 6.323,5.333 0.615,0.198 10 false E02 5.844,5.948 6.458,6.146 0.615,0.198 10 false ECM 5.25,0.698 5.708,0.896 0.458,0.198 10 false G129 5.25,1.229 5.708,1.427 0.458,0.198 10 false G129 5.25,1.969 5.708,2.167 0.458,0.198 10 false G129 5.25,2.521 5.708,2.719 0.458,0.198 10 false G130 5.25,3.115 5.708,3.313 0.458,0.198 10 false G130 5.25,3.583 5.708,3.781 0.458,0.198 10 false G130 5.302,4.135 5.76,4.333 0.458,0.198 10 false C74 5.271,4.646 5.729,4.844 0.458,0.198 10 false C73 5.292,5.146 5.75,5.344 0.458,0.198 10 false C73 5.385,3.927 5.542,4.125 0.156,0.198 10 false 7 5.385,4.438 5.542,4.635 0.156,0.198 10 false 7 5.375,4.958 5.531,5.156 0.156,0.198 10 false 6 5.354,0.49 5.667,0.688 0.313,0.198 10 false 24 5.344,1 5.656,1.198 0.313,0.198 10 false 23 5.375,1.76 5.531,1.958 0.156,0.198 10 false 2 5.365,2.323 5.521,2.521 0.156,0.198 10 false 1 5.385,2.896 5.542,3.094 0.156,0.198 10 false 8 5.385,3.375 5.542,3.573 0.156,0.198 10 false 9 1.656,0.563 1.813,0.76 0.156,0.198 10 false 1 1.635,1.083 1.948,1.281 0.313,0.198 10 false 2 0.208,1.469 0.667,1.667 0.458,0.198 10 false G122 0.219,1.656 2.24,1.969 2.021,0.313 10 false No. 2 CAN Junction Connector 3.667,1.781 4.438,1.979 0.771,0.198 10 false EFI-B 3.521,3.417 4.292,3.615 0.771,0.198 10 false IG2 NO.1 1.688,1.927 3.521,2.125 1.833,0.198 10 false from Battery 0.813,2.469 2.646,2.667 1.833,0.198 10 false from EFI-MAIN NO.1 Relay 0.948,3.063 2.781,3.26 1.833,0.198 10 false to EFI-MAIN NO.1 Relay 0.271,3.563 2.646,3.76 2.375,0.198 10 false from IG2 Relay*1, Ignition Switch*2 0.198,5.865 2.573,6.063 2.375,0.198 10 false *1: w/ Smart Entry and Start System 0.208,6.271 2.583,6.469 2.375,0.198 10 false *2: w/o Smart Entry and Start System

for 1GD-FTV:
C317092E06
5.688,0.583 6.302,0.781 0.615,0.198 10 false CANH 5.677,1.365 6.292,1.563 0.615,0.198 10 false CANL 5.344,1.01 5.656,1.208 0.313,0.198 10 false 28 5.365,0.469 5.677,0.667 0.313,0.198 10 false 17 5.281,0.698 5.74,0.896 0.458,0.198 10 false G49 5.281,1.219 5.74,1.417 0.458,0.198 10 false G49 0.063,1.438 0.521,1.635 0.458,0.198 10 false G122 0.063,1.625 4.344,1.823 4.281,0.198 10 false No. 2 CAN Junction Connector 1.604,0.563 1.917,0.76 0.313,0.198 10 false 1 1.625,1.104 1.938,1.302 0.313,0.198 10 false 2 5.729,3.854 6.344,4.052 0.615,0.198 10 false MREL 5.729,2.531 6.344,2.729 0.615,0.198 10 false +B 5.719,2.969 6.333,3.167 0.615,0.198 10 false +B2 5.698,3.438 6.313,3.635 0.615,0.198 10 false +B3 5.698,1.958 6.313,2.156 0.615,0.198 10 false BATT 5.719,4.333 6.333,4.531 0.615,0.198 10 false IGSW 5.708,4.844 6.323,5.042 0.615,0.198 10 false E1 5.302,4.823 5.76,5.021 0.458,0.198 10 false C41 5.885,5.365 6.344,5.563 0.458,0.198 10 false ECM 5.396,4.615 5.708,4.813 0.313,0.198 10 false 1 5.385,1.74 5.698,1.938 0.313,0.198 10 false 1 5.281,1.958 5.74,2.156 0.458,0.198 10 false G50 5.292,4.323 5.75,4.521 0.458,0.198 10 false G50 5.354,4.115 5.667,4.313 0.313,0.198 10 false 18 5.344,3.625 5.656,3.823 0.313,0.198 10 false 14 5.281,3.844 5.74,4.042 0.458,0.198 10 false G49 5.281,2.521 5.74,2.719 0.458,0.198 10 false G50 5.271,2.969 5.729,3.167 0.458,0.198 10 false G50 5.281,3.417 5.74,3.615 0.458,0.198 10 false G50 5.385,2.292 5.698,2.49 0.313,0.198 10 false 2 5.375,2.771 5.688,2.969 0.313,0.198 10 false 3 5.385,3.188 5.698,3.385 0.313,0.198 10 false 4 0.781,2.49 2.49,2.865 1.708,0.375 10 false from EFI-MAIN NO.1 Relay 0.323,4.281 2.656,4.573 2.333,0.292 10 false from IG2 Relay*1, Ignition Switch*2 3.635,1.802 4.448,2 0.813,0.198 10 false EFI-B 3.5,4.156 4.313,4.354 0.813,0.198 10 false IG2 NO.1 1.646,1.969 2.479,2.344 0.833,0.375 10 false from Battery 0.927,3.833 2.479,4.135 1.552,0.302 10 false to EFI-MAIN NO.1 Relay 0.219,4.99 2.552,5.281 2.333,0.292 10 false *1: w/ Smart Entry and Start System 0.229,5.344 2.563,5.635 2.333,0.292 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch ON, wait at least 20 seconds, and then drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for 2TR-FE A
for 1GR-FE B
for 1KD-FTV C
for 1GD-FTV D



A

2.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)

B

4.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)

C

6.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)

D

8.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C317098C03
1.458,0.458 1.906,0.74 0.448,0.281 2.344,3.167 2.198,3.167 2.198,3.167 2.073,2 true 2.521,2.854 2.375,2.854 2.375,2.854 2.219,2.01 true 1.552,0.51 2.01,0.708 0.458,0.198 10 false G56 2.583,2.771 3.208,2.99 0.625,0.219 10 false CANL 2.427,3.063 3.052,3.302 0.625,0.24 10 false CANH 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G56-13 (CANH) - G56-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C317087C02
0.875,0.51 1.302,0.771 0.427,0.26 3.375,0.521 3.802,0.781 0.427,0.26 5.917,0.531 6.344,0.792 0.427,0.26 0.5,0.573 0.635,0.573 0.635,0.573 0.917,1.375 true 4.354,0.906 4.219,0.906 4.219,0.906 4.135,1.385 true 5.531,0.906 5.667,0.906 5.667,0.906 5.969,1.385 true 0.438,0.792 0.573,0.792 0.573,0.792 0.75,1.396 true 0.323,1.042 0.458,1.042 0.458,1.042 0.573,1.396 true 0.854,2.323 0.719,2.323 0.719,2.323 0.552,1.615 true 0.958,0.552 1.417,0.75 0.458,0.198 10 false G57 3.469,0.573 3.927,0.771 0.458,0.198 10 false G56 6.01,0.573 6.469,0.771 0.458,0.198 10 false C14 0.083,0.969 0.354,1.167 0.271,0.198 10 false +B 4.448,0.813 5.063,1.01 0.615,0.198 10 false MREL 0.083,0.5 0.698,0.698 0.615,0.198 10 false BATT 5.313,0.833 5.927,1.031 0.615,0.198 10 false E1 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.115,0.729 0.531,0.927 0.417,0.198 10 false +B2 0.917,2.25 1.531,2.448 0.615,0.198 10 false IGSW
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G57-3 (BATT) - Body ground Always 11 to 14 V
G57-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G56-6 (MREL) 11 to 14 V
G57-2 (+B2) - Body ground Battery positive (+) voltage applied to terminal G56-6 (MREL) 11 to 14 V
G57-8 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C329346C02
2.344,0.938 2.813,1.229 0.469,0.292 0.854,1.969 0.99,1.969 0.99,1.969 1.292,1.573 true 0.813,1.042 0.948,1.042 0.948,1.042 1.292,1.375 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.438,1.865 0.885,2.063 0.448,0.198 10 false CANH 2.406,0.979 3.021,1.177 0.615,0.198 10 false G159 0.396,0.938 0.833,1.135 0.438,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Connector Specified Condition
G159-31 (CANH) - G159-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

5.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C329345C04
0.344,0.385 0.802,0.667 0.458,0.281 4.99,0.354 5.448,0.635 0.458,0.281 2.698,0.396 3.156,0.677 0.458,0.281 0.51,1.5 0.646,1.5 0.646,1.5 1.052,1.188 true 6.365,1.292 6.521,1.146 6.521,1.146 6.625,1.146 true 2.927,0.969 3.063,0.969 3.063,0.969 3.427,1.313 true 3,1.604 3.135,1.604 3.135,1.604 3.635,1.365 true 3.917,1.354 4.396,1.604 4.396,1.604 4.5,1.604 true 4.146,1.281 4.417,1.229 4.417,1.229 4.521,1.229 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 0.188,1.427 0.521,1.625 0.333,0.198 10 false E01 0.406,0.417 0.865,0.615 0.458,0.198 10 false C118 6.698,1.031 7.156,1.229 0.458,0.198 10 false MREL 5.063,0.396 5.521,0.594 0.458,0.198 10 false G159 2.76,0.438 3.219,0.635 0.458,0.198 10 false G158 2.49,0.885 2.948,1.083 0.458,0.198 10 false IGSW 2.656,1.479 3.115,1.677 0.458,0.198 10 false +B2 4.573,1.469 5.031,1.667 0.458,0.198 10 false +B 4.563,1.125 5.021,1.323 0.458,0.198 10 false BATT
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G158-24 (BATT) - Body ground Always 11 to 14 V
G158-23 (+B) - Body ground Battery positive (+) voltage applied to terminal G159-36 (MREL) 11 to 14 V
G158-22 (+B2) - Body ground Battery positive (+) voltage applied to terminal G159-36 (MREL) 11 to 14 V
G158-21 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C118-23 (E01) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C317098C13
1.458,0.823 1.906,1.104 0.448,0.281 2.833,1.615 2.688,1.615 2.688,1.615 2.063,2.083 true 2.531,2.885 2.313,2.885 2.313,2.885 1.938,2.156 true 1.521,0.865 1.979,1.063 0.458,0.198 10 false G129 2.896,1.49 3.313,1.75 0.417,0.26 10 false CANH 2.583,2.781 3.031,2.979 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G129-24 (CANH) - G129-23 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

7.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C329269C02
1.802,0.177 2.281,0.469 0.479,0.292 5.01,0.177 5.49,0.469 0.479,0.292 5.063,1.865 5.542,2.156 0.479,0.292 1.781,1.875 2.26,2.167 0.479,0.292 1.115,0.656 1.26,0.656 1.26,0.656 1.531,0.99 true 0.958,1.563 1.104,1.563 1.104,1.563 1.51,1.208 true 1.156,1.896 1.302,1.896 1.302,1.896 1.656,1.229 true 4.438,0.583 4.583,0.583 4.583,0.583 5.01,0.979 true 6.24,2.25 6.073,2.25 6.073,2.25 5.875,2.656 true 3.156,2.208 2.99,2.208 2.99,2.208 2.385,2.635 true 3.104,2.521 2.938,2.521 2.938,2.521 2.563,2.656 true 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.865,0.229 2.323,0.427 0.458,0.198 10 false G130 5.094,0.219 5.552,0.417 0.458,0.198 10 false G129 1.885,1.927 2.344,2.125 0.458,0.198 10 false C73 5.167,1.906 5.625,2.104 0.458,0.198 10 false C74 4.021,0.5 4.635,0.698 0.615,0.198 10 false BATT 0.875,0.583 1.49,0.781 0.615,0.198 10 false +B 0.542,1.49 1.156,1.688 0.615,0.198 10 false MREL 0.74,1.823 1.354,2.021 0.615,0.198 10 false IGSW 6.313,2.177 6.927,2.375 0.615,0.198 10 false E1 3.167,2.448 3.781,2.646 0.615,0.198 10 false E01 3.229,2.135 3.844,2.333 0.615,0.198 10 false E02
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G129-2 (BATT) - Body ground Always 11 to 14 V
G130-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G130-8 (MREL) 11 to 14 V
G130-9 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C74-7 (E1) - Body ground Always Below 1 Ω
C73-7 (E01) - Body ground Always Below 1 Ω
C73-6 (E02) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C317098C04
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G49 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-17 (CANH) - G49-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

9.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C317088C02
1,0.448 1.448,0.719 0.448,0.271 3.25,0.438 3.698,0.708 0.448,0.271 5.552,0.406 6,0.677 0.448,0.271 0.469,1.052 0.604,1.052 0.604,1.052 0.688,1.406 true 3,0.823 3.135,0.823 3.135,0.823 3.823,1.573 true 4.917,0.865 5.052,0.865 5.052,0.865 5.219,1.406 true 0.5,2.417 0.635,2.417 0.635,2.417 0.708,1.771 true 0.49,0.823 0.625,0.823 0.625,0.823 0.865,1.396 true 0.615,0.594 0.75,0.594 0.75,0.594 1.031,1.396 true 1.896,0.896 1.729,0.896 1.729,0.896 1.24,1.406 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.094,0.51 1.552,0.708 0.458,0.198 10 false G50 3.333,0.49 3.792,0.688 0.458,0.198 10 false G49 5.656,0.469 6.115,0.667 0.458,0.198 10 false C41 0.063,0.969 0.469,1.177 0.406,0.208 10 false BATT 4.677,0.781 4.958,0.969 0.281,0.188 10 false E1 2.573,0.75 2.979,0.958 0.406,0.208 10 false MREL 0.24,0.75 0.646,0.958 0.406,0.208 10 false +B 0.302,0.531 0.708,0.74 0.406,0.208 10 false +B2 1.958,0.813 2.365,1.021 0.406,0.208 10 false +B3 0.073,2.344 0.531,2.573 0.458,0.229 10 false IGSW
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G50-1 (BATT) - Body ground Always 11 to 14 V
G50-2 (+B) - Body ground Battery positive (+) voltage applied to terminal G49-14 (MREL) 11 to 14 V
G50-3 (+B2) - Body ground Battery positive (+) voltage applied to terminal G49-14 (MREL) 11 to 14 V
G50-4 (+B3) - Body ground Battery positive (+) voltage applied to terminal G49-14 (MREL) 11 to 14 V
G50-18 (IGSW) - Body ground Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR