Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat)
RM33K0E _58 Vehicle Interior _043553 SEAT _0227126 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power door lock control system (Click here)

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

AIRBAG SYSTEM (for Type A):

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

AIRBAG SYSTEM (for Type B):

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 72138J 3.REMOVE FRONT SEAT REAR OUTER TRACK COVER LH

a.

Operate the seat track handle sub-assembly LH to slide the front seat assembly LH to the frontmost position.


b.
B433046C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.


c.

Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear outer track cover LH.


Hide 72138H 4.REMOVE FRONT SEAT REAR INNER TRACK COVER LH

a.
B433047C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.


b.

Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear inner track cover LH.


Hide 5.REMOVE FRONT SEAT ASSEMBLY LH

a.
B433043

Remove the 2 bolts on the rear side of the front seat assembly LH.


b.

Operate the seat track handle sub-assembly LH to slide the front seat assembly LH to the rearmost position.


c.
B433044

Remove the 2 bolts.


d.

Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the center position.


e.

Operate the power seat switch knob LH (for Vertical) to set the seat cushion height of the front seat assembly LH to the uppermost position.


f.

Operate the power seat switch knob LH (for Reclining) to set the seatback of the front seat assembly LH to the perpendicular position.


g.

w/ Front Seat Side Airbag:

Disconnect the front seat airbag assembly LH connector.

i.

Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

B273982C12
3.573,1.281 4.156,0.865 false 4.198,0.792 4.417,1 0.219,0.208 10 false *1 2.833,0.51 3.083,0.667 0.25,0.156 10 false *b 0.688,0.5 0.917,0.698 0.229,0.198 10 false *a
*1 Slider - -
*a Push *b Slide




h.
B433045

Disconnect the connector.


i.

Detach the wire harness clamp.


j.
B439076

Remove the front seat assembly LH as shown in the illustration.

NOTICE:
·

Protect the front seat legs.


·

Do not damage the front seat assembly LH, body exterior or interior parts.