Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat) › 2015.11–2016.07
RM33K0E _58 Vehicle Interior _043553 SEAT _0227126 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 71052A 1.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH

a.
B433079C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While rotating the part in installation direction (1) shown in the illustration, attach the hook.


b.

Push in Installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly LH.


Hide 82192 2.INSTALL FRONT SEAT WIRE LH

a.
B433110C02
2.323,1.938 2.385,1.573 2.385,1.573 2.552,1.573 true 1.365,2.01 1.531,1.583 1.531,1.583 1.74,1.583 true 1.469,3.031 1.635,3.031 1.635,3.031 1.719,2.583 true 2.719,2.927 2.531,2.927 2.531,2.927 2.438,2.479 true 1.75,1.49 1.938,1.667 0.188,0.177 10 true *1 2.563,1.479 2.75,1.656 0.188,0.177 10 true *2 1.271,2.958 1.458,3.135 0.188,0.177 10 false *1 2.729,2.833 2.917,3.01 0.188,0.177 10 false *1
*1 Wire Harness Clamp
*2 Connector Clamp


Connect the 3 connectors.


b.

Attach the wire harness clamp and connector clamp.


Hide 71538B 3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

a.
B433080C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to install the guide.


b.

While expanding the part in installation direction (2) shown in the illustration, attach the claw.


c.

Install the front seat cushion edge protector LH with the screw.


Hide 71537G 4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure as for the LH side.


Hide 71874 5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

a.
B433081C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to attach the guide.


b.

Push in the installation direction (2) shown in the illustration to attach the clip.


c.
B433082C01
0,0 0,0 false
V113147

Install in this Direction


Push in the guide in the installation direction shown in the illustration.


d.

Install the front seat lower cushion shield LH with the screw.


Hide 71873 6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL SEAT COVER WIRE

a.
B433083N03
1.698,0.833 2.115,0.417 true 1.323,0.396 1.708,0.833 true 1.708,1.604 1.708,1.281 true 1.698,2.573 1.698,2.25 true 2.688,1.979 3.031,1.813 true 2.615,0.854 2.958,0.688 true 0.469,0.708 0.792,0.854 true 0.396,1.781 0.719,1.927 true 1.635,0.875 1.792,1.073 0.156,0.198 10 true A 1.635,1.625 1.792,1.823 0.156,0.198 10 true C 1.625,2.594 1.781,2.792 0.156,0.198 10 true D 0.281,0.583 0.438,0.781 0.156,0.198 10 true B 3,0.583 3.156,0.781 0.156,0.198 10 true B 3.063,1.698 3.219,1.896 0.156,0.198 10 true E 0.219,1.667 0.375,1.865 0.156,0.198 10 true E

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 170 mm (6.70 in.)
B 150 mm (5.91 in.)
C 230 mm (9.06 in.)
D 270 mm (10.63 in.)
E 290 mm (11.42 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71071S 8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394024E01
2.5,0.24 3.271,0.438 0.771,0.198 10 false A - A 4.656,0.302 5.427,0.5 0.771,0.198 10 false B - B 0.198,0.396 0.354,0.594 0.156,0.198 10 false A 0.51,0.583 0.656,0.75 0.146,0.167 10 true A 0.938,0.802 1.094,1 0.156,0.198 10 false B 1.26,1.063 1.656,1.406 0.396,0.344 10 false B



a.

Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

B433084C01
4.927,0.917 5.104,0.917 true 5.24,2.125 5.313,1.667 false 5.177,2.167 5.49,2.323 0.313,0.156 10 false *1 5.125,0.823 5.438,0.979 0.313,0.156 10 false *a 2.594,1.781 2.813,1.99 0.219,0.208 10 true (1) 1.938,1.792 2.156,2 0.219,0.208 10 true (2) 2.552,1.146 2.771,1.354 0.219,0.208 10 true (3) 2.021,1.146 2.24,1.354 0.219,0.208 10 true (4) 1.385,1.833 1.604,2.042 0.219,0.208 10 true (5) 1.438,1.406 1.656,1.615 0.219,0.208 10 true (6) 1.448,1.104 1.667,1.313 0.219,0.208 10 true (7) 1.49,0.781 1.708,0.99 0.219,0.208 10 true (8) 1.51,0.521 1.729,0.729 0.219,0.208 10 true (9) 3.146,1.844 3.417,2.052 0.271,0.208 10 true (10) 3.063,1.396 3.333,1.604 0.271,0.208 10 true (11) 3.073,1.094 3.354,1.302 0.281,0.208 10 true (12) 3.042,0.781 3.333,0.99 0.292,0.208 10 true (13) 3.042,0.51 3.333,0.708 0.292,0.198 10 true (14) 1.781,0.208 2.073,0.406 0.292,0.198 10 true (15) 2.073,0.208 2.365,0.406 0.292,0.198 10 true (16) 2.448,0.208 2.74,0.406 0.292,0.198 10 true (17) 2.75,0.208 3.042,0.406 0.292,0.198 10 true (18)
*1 Hog Ring Pliers - -
*a Cutout - -



c.

Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

HINT:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.



B433085C02
5,2.083 5.125,1.552 false 4.938,2.104 5.25,2.26 0.313,0.156 10 false *1
*1 Hog Ring Pliers - -



Hide 9.INSTALL SEAT CUSHION COVER WITH PAD

a.

While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to install the seat cushion cover with pad.

B433050


Hide 71587B 10.INSTALL FRONT SEATBACK EDGE PROTECTOR

a.
B409604

Attach the claw to Install the 2 front seatback edge protectors.


Hide 71054S 11.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH

a.
B433086C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly LH.


b.

Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly LH.


c.

Push in installation direction (2) shown in the illustration to install the front seatback spring sub-assembly LH.


d.
B403873

Attach the claw and install the 2 front seatback edge protectors.


Hide 71759D 12.INSTALL FRONT NO. 2 SEATBACK HOOK

a.
B403872C01
0,0 0,0 false
V113147

Install in this Direction


Push up installation direction shown in the illustration to attach the claw and install the 2 front No. 2 seatback hooks.


Hide 73920A 13.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)

Hide 8219B 14.INSTALL FRONT SEAT NO. 2 WIRE LH

a.
B433109

Connect the connector.


b.

Attach the wire harness clamp and install the front seat No. 2 wire LH.


Hide 15.INSTALL SEAT COVER WIRE

a.
B403865N01
2.25,1.427 3.031,1.167 true 2.094,3.135 3.031,2.427 true 3.125,1.052 3.281,1.25 0.156,0.198 10 false A 3.125,2.313 3.281,2.51 0.156,0.198 10 false B

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 200 mm (7.87 in.)
B 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71073S 16.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B



a.

Set the separate type front seatback cover.


b.

Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

HINT:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.


B409606C01
5.25,2.229 5.24,1.646 true 5.094,0.948 4.958,0.938 true 3.417,0.427 3.063,0.719 true 1.74,0.302 2,0.563 true 1.563,0.802 1.979,1.188 true 1.563,0.792 2.271,1.156 true 2.75,1.219 3.365,1.146 true 2.927,1.375 3.365,1.156 true 5.115,0.854 5.427,1.052 0.313,0.198 10 false *a 5.198,2.281 5.51,2.479 0.313,0.198 10 false *1 3.417,0.229 3.875,0.427 0.458,0.198 10 false (1) 1.563,0.135 2.021,0.333 0.458,0.198 10 false (1) 1.365,0.677 1.823,0.875 0.458,0.198 10 false (2) 3.417,1.052 3.875,1.25 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -




Hide 17.INSTALL SEATBACK COVER WITH PAD

a.
B433087C02
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.


b.

w/ Front Seat Side Airbag:

i.
B439072C02
0.677,2.281 1.438,1.792 true 1.76,2.698 2.552,2.74 true 0.531,2.313 0.844,2.469 0.313,0.156 10 false *1 2.583,2.656 2.896,2.813 0.313,0.156 10 false *2
*1 J Hook A
*2 J Hook B
V113147

Install in this Direction


Push in installation direction shown in the illustration to attach the J hook A and J hook B.


ii.
B439073C02
2.104,1.26 2.521,0.635 true 0.844,3.177 1.25,2.854 true 0.708,3.198 1.021,3.354 0.313,0.156 10 false *1 2.479,0.458 2.792,0.615 0.313,0.156 10 false *2
*1 J Hook B (J Hook A and J Hook B)
*2 J Hook C
V113147

Install in this Direction


Push in installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.


iii.

Install the new rivet to J hook B.

B413208C05
2.219,1.656 3.104,1.177 true 0.74,1.75 1.854,1.729 true 5.542,1.771 6.625,1.656 true 4.229,1.135 5.208,1.583 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 3.604,0.146 3.917,0.344 0.313,0.198 10 false *B 0.542,1.677 0.854,1.875 0.313,0.198 10 false *1 6.688,1.542 7,1.74 0.313,0.198 10 false *1 3.167,1.063 3.479,1.26 0.313,0.198 10 false *2 4.021,1.063 4.333,1.26 0.313,0.198 10 false *2
*A for LH seat *B for RH seat
*1 J Hook A *2 J Hook B



iv.

Place your hand at the position shown in the illustration and push in installation direction to attach the J hook B.

B439074C02
2.344,1.438 2.833,1.146 true 1.635,0.906 1.396,0.646 true 1.354,2.219 1.927,1.667 true 1.25,2.24 1.563,2.396 0.313,0.156 10 false *1 2.865,1.031 3.177,1.188 0.313,0.156 10 false *2 1.25,0.479 1.563,0.635 0.313,0.156 10 false *3
*1 J Hook A *2 J Hook B
*3 J Hook C - -
V113146

Place Hand Here
V113147

Install in this Direction




Hide 71931 18.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B403861C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the 2 front seat headrest supports.


b.
B433064C04
0,0 0,0 false
V113147

Install in this Direction


Pull up installation direction shown in the illustration to attach the guide to the 2 straps.


c.
B433088C02
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


d.
B433111C01
0.083,0.083 0.396,0.24 0.313,0.156 10 false *A 0.083,2.417 0.396,2.573 0.313,0.156 10 false *B
*A w/ Side Airbag System
*B w/o Side Airbag System
V113147

Install in this Direction


Pass the wire harness through the opening in the back cover.


e.

Using hog ring pliers, install 5 new hog rings.

B433089C02
4.938,0.917 5.125,0.917 true 5.156,2.188 5.292,1.656 false 5.104,2.208 5.417,2.365 0.313,0.156 10 false *1 5.135,0.823 5.448,0.979 0.313,0.156 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -



Hide 71759C 19.INSTALL FRONT NO. 1 SEATBACK HOOK

a.
B433090

Attach the claw and install the front No. 1 seatback hook.


Hide 71876G 20.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.
B433091C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push down installation direction (1) shown in the illustration.


b.

Rotate the part in installation direction (2) shown in the illustration and align the guide to install the reclining adjuster inside cover LH.


Hide 71875F 21.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71014S 22.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

a.
B413542C04
0.125,0.167 0.333,0.354 0.208,0.188 10 true *A 0.146,2.563 0.354,2.75 0.208,0.188 10 true *B
*A LH Side
*B RH Side


Install the 4 bolts and front seatback frame sub-assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B439079C02
2.479,2.021 1.781,2.021 1.781,2.021 0.792,1.469 true 1.958,3.938 1.365,4.427 1.365,4.427 0.927,4.427 true 0.083,0.083 0.396,0.24 0.313,0.156 10 true *A 0.083,2.417 0.396,2.573 0.313,0.156 10 true *B 2.49,1.927 2.677,2.125 0.188,0.198 10 false *1 0.729,4.333 0.917,4.531 0.188,0.198 10 false *1
*A LH Side
*B RH Side
*1 Separate Type Front Seat Cushion Cover


Attach the hook.


c.
B433108

Connect the Connector and attach the guide.


d.

w/ Front Seat Side Airbag:

i.
B433107

Attach the wire harness clamp.


ii.
B433065C04
0.729,0.865 0.854,0.531 0.854,0.531 1.094,0.531 true 1.469,1.344 1.594,1.01 1.594,1.01 1.833,1.01 true 2.5,1.781 2.625,1.448 2.625,1.448 2.865,1.448 true 2.25,2.719 2.51,2.719 2.51,2.719 2.667,2.302 true 1.115,0.438 1.427,0.594 0.313,0.156 10 true *1 2.052,2.635 2.229,2.813 0.177,0.177 10 true *2 1.854,0.917 2.167,1.073 0.313,0.156 10 true *1 2.885,1.354 3.198,1.51 0.313,0.156 10 true *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the wire harness clamp and connector clamp.



e.
B433062

Install the band in the position shown in the illustration.


Hide 73240 23.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 24.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

a.
B433092C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


b.
B433093C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield LH.


Hide 84922C 25.INSTALL FRONT POWER SEAT SWITCH LH

Hide 71812D 26.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B433106C02
2.031,2.375 1.917,2.052 1.917,2.052 1.74,2.052 true 2.104,3.167 2.26,3.167 2.26,3.167 2.302,2.833 true 2.74,2.792 2.698,2.469 2.698,2.469 2.542,2.469 true 2.885,3.177 3.083,3.177 3.083,3.177 3.094,3 true 1.917,3.083 2.094,3.26 0.177,0.177 10 false *1 2.344,2.396 2.531,2.583 0.188,0.188 10 true *2 1.563,1.969 1.729,2.146 0.167,0.177 10 false *3 2.688,3.094 2.875,3.271 0.188,0.177 10 false *4
*1 Wire Harness Clamp
*2 Connector Clamp
*3 Hook A
*4 Hook B


Attach the claw.


b.

Attach the hook B.


c.

Attach the wire harness clamp and connector clamp.


d.

Connect the 2 connectors.


e.

Attach the hook A.


f.
B433112C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the guide, claw and clip.


g.
B433113C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the clip and guide.


h.
B433096C02
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the front seat cushion shield LH.


Hide 71868A 27.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH

a.
B433114C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to install the guide.


b.

Install the screw and front seat inner No. 1 cushion shield LH.


Hide 84921K 28.INSTALL POWER SEAT SWITCH KNOB LH (for Reclining)

a.
B433115C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob LH.


Hide 84921D 29.INSTALL POWER SEAT SWITCH KNOB LH (for Slide and Vertical, Lifter)

a.
B433116C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob LH.


Hide 71849 30.INSTALL SEAT ADJUSTER COVER CAP LH

a.
B433099C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to install the 2 seat adjuster cover caps LH.


Hide 71910A 31.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.
B411002C01
0,0 0,0 false
V100136

Apply Silicon


Apply silicon lubricant in this range.


b.

Install the front seat headrest assembly.