Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP
RM33K0E _59 Vehicle Exterior _043564 EXTERIOR PANELS / TRIM _0227155 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 51774C 1.REMOVE STEP PLATE COVER LH

a.

Remove the 2 bolts.

B410768


b.

Detach the claw and guide and remove the step plate cover LH.

NOTICE:
·

When removing the step plate cover LH, be careful not to damage the claws.

·

If the step plate cover LH or its claws are damaged, replace it with a new one.




Hide 51082 2.REMOVE NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH

a.

Put a 5 mm (0.197 in.) drill bit into a drill.

B410769E01
0.49,0.969 0.76,1.25 0.271,0.281 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Remove the No. 1 side step stay sub-assembly LH from the step plate LH.


e.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.


Hide 51796 3.REMOVE NO. 2 SIDE STEP BRACKET LH

a.

Put a 5 mm (0.197 in.) drill bit into a drill.

B410771E01
0.479,0.958 0.656,1.167 0.177,0.208 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Remove the No. 2 side step bracket LH from the step plate LH.


e.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.


Hide 51798 4.REMOVE NO. 3 SIDE STEP BRACKET LH

a.

Put a 5 mm (0.197 in.) drill bit into a drill.

B410773E01
0.479,0.958 0.635,1.156 0.156,0.198 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Remove the No. 3 side step bracket LH from the step plate LH.


e.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.