Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM33K0E _59 Vehicle Exterior _043564 EXTERIOR PANELS / TRIM _0227160 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/ Roof Rack)

NOTICE:
·

It is only necessary to perform this procedure when replacing a roof drip side finish moulding clip with a new one.

·

If installing new roof drip side finish moulding clips, remove the adhesive remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.



HINT:

When installing the roof drip side finish moulding clip, heat the vehicle body and roof drip side finish moulding clip using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding Clip 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B187426C10
2.073,0.781 2.385,0.781 false 0.99,1.052 1.229,1.052 1.229,1.052 1.344,1.51 true 1.823,0.667 2.052,0.854 0.229,0.188 10 false *1 0.74,0.938 1.031,1.135 0.292,0.198 10 false *a
*1 Adhesive
*a 2.0 to 3.0 mm Bead of Adhesive


Apply a 2.0 to 3.0 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1991 psi) or more (when the temperature is 23°C (73°F))



b.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.
B409527C01
2.906,0.74 3.073,0.74 false 1,1.229 1.156,1.427 0.156,0.198 10 false A 3.115,0.646 3.333,0.958 0.219,0.313 10 false *a 2.698,0.281 2.854,0.479 0.156,0.198 10 false B
*a Edge of Curved Surface


While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the roof drip side finish moulding clip after lightly pressing it so that the adhesive adheres to the primer.

Standard:
Area Specified Condition
A 4.9 mm (0.193 in.)
B 8.2 mm (0.323 in.)


NOTICE:

Install the roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75561A 2.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/o Roof Rack)

NOTICE:
·

It is only necessary to perform this procedure when replacing a roof drip side finish moulding clip with a new one.

·

If installing new roof drip side finish moulding clips, remove the adhesive remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.



HINT:

When installing the roof drip side finish moulding clip, heat the vehicle body and roof drip side finish moulding clip using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding Clip 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B187426C10
2.073,0.781 2.385,0.781 false 0.99,1.052 1.229,1.052 1.229,1.052 1.344,1.51 true 1.823,0.667 2.052,0.854 0.229,0.188 10 false *1 0.74,0.938 1.031,1.135 0.292,0.198 10 false *a
*1 Adhesive
*a 2.0 to 3.0 mm Bead of Adhesive


Apply a 2.0 to 3.0 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1991 psi) or more (when the temperature is 23°C (73°F))



b.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the roof drip side finish moulding clip after lightly pressing it so that the adhesive adheres to the primer.

B414874C02
6.594,3.417 6.698,3.417 false 2.646,2.188 2.521,2.188 false 0.969,2.583 1.125,2.781 0.156,0.198 10 false A 2.365,1.813 2.521,2.01 0.156,0.198 10 false B 4.656,3.844 4.813,4.042 0.156,0.198 10 false C 5.042,3.833 5.198,4.031 0.156,0.198 10 false D 6.438,3.042 6.594,3.24 0.156,0.198 10 false E 6.729,3.333 7.042,3.531 0.313,0.198 10 false *a 2.656,2.094 2.969,2.292 0.313,0.198 10 false *a
*a Edge of Curved Surface - -


Standard:
Area Specified Condition Area Specified Condition
A 4.9 mm (0.193 in.) B 8.2 mm (0.323 in.)
C 6.2 mm (0.244 in.) D 4.4 mm (0.173 in.)
E 8.2 mm (0.323 in.) - -


NOTICE:

Install the roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75552 3.INSTALL ROOF DRIP SIDE FINISH MOULDING LH (w/ Roof Rack)

a.
B409526

Attach the clip to install the roof drip side finish moulding LH.


b.

Remove the protective tape.


Hide 75552 4.INSTALL ROOF DRIP SIDE FINISH MOULDING LH (w/o Roof Rack)

a.
B414886

Attach the clip to install the roof drip side finish moulding LH.


b.

Remove the protective tape.


Hide 63470A 5.INSTALL ROOF RACK ASSEMBLY LH (w/ Roof Rack)