Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM33K0E _52 Drivetrain _043529 VF2CM TRANSFER / 4WD / AWD _0227239 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM Y

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure listed to troubleshoot the touch select 2-4 and high-low system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM

HINT:

The ECU of this system is connected to the CAN communication system.

Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.



Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK DTC AND FREEZE FRAME DATA*

B

5.CHECK DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Trouble Codes
50001 363

b.

Check for freeze frame data.

HINT:

Record or print DTCs and freeze frame data if necessary.



c.

Clear the DTCs and freeze frame data.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Clear DTCs
50002 363

d.

Recheck for DTCs.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Trouble Codes
50001 363
i.

Simulate the malfunction condition and check if the DTCs are output again.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.PROBLEM SYMPTOMS TABLE

B

10.GO TO DTC CHART
6.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault not listed in problem symptoms table A
Fault listed in problem symptoms table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.REPAIR OR REPLACE
7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.REPAIR OR REPLACE
8.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

9.CONFIRM TEST
9.CONFIRM TEST
Result:
Proceed to
NEXT



NEXT

END

10.GO TO DTC CHART
Result:
Proceed to
NEXT



NEXT

8.REPAIR OR REPLACE