Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM33K0E _52 Drivetrain _043529 VF2CM TRANSFER / 4WD / AWD _0227239 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM J

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  Shift Motor Circuit  


WIRING DIAGRAM

C326380E07
1.938,2.063 2.396,2.26 0.458,0.198 10 false TM1 1.969,2.75 2.427,2.948 0.458,0.198 10 false TM2 0.802,2.438 1.635,2.75 0.833,0.313 10 false Transfer Shift Motor 0.406,3.354 0.865,3.552 0.458,0.198 10 false C63 0.448,3.563 2.542,3.74 2.094,0.177 10 false Transfer Shift Actuator Assembly 2.302,2.083 2.458,2.281 0.156,0.198 10 false 2 4.167,2.083 4.323,2.281 0.156,0.198 10 false 8 4.385,2.083 4.844,2.281 0.458,0.198 10 false TM1 4.188,2.75 4.344,2.948 0.156,0.198 10 false 7 4.365,2.75 4.823,2.948 0.458,0.198 10 false TM2 4.188,4.854 4.344,5.052 0.156,0.198 10 false 2 4.365,4.854 4.823,5.052 0.458,0.198 10 false DM1 4.188,5.521 4.344,5.719 0.156,0.198 10 false 6 4.365,5.51 4.823,5.708 0.458,0.198 10 false DM2 1.948,4.844 2.406,5.042 0.458,0.198 10 false DM1 2.313,4.844 2.469,5.042 0.156,0.198 10 false 1 1.948,5.51 2.406,5.708 0.458,0.198 10 false DM2 2.323,5.521 2.479,5.719 0.156,0.198 10 false 2 0.49,6.177 0.948,6.375 0.458,0.198 10 false C57 0.5,6.375 3.167,6.76 2.667,0.385 10 true A.D.D. Actuator (Differential Motor Actuator Assembly) 4.333,7.438 4.792,7.635 0.458,0.198 10 false C61 4.667,7.427 6.365,7.625 1.698,0.198 10 false 4 Wheel Drive Control ECU 6.177,5.875 6.49,6.073 0.313,0.198 10 false IG 5.521,0.76 5.833,0.958 0.313,0.198 10 false IG 5.49,2.417 5.927,2.604 0.438,0.188 10 false RY1-1 5.49,3.104 6.26,3.302 0.771,0.198 10 false RY1-2 5.469,5.188 6.24,5.385 0.771,0.198 10 false RY2-1 5.469,5.865 6.24,6.063 0.771,0.198 10 false RY2-2 0.833,5.177 1.604,5.615 0.771,0.438 10 false A.D.D. Shift Motor 2.323,2.76 2.479,2.958 0.156,0.198 10 false 1

C325506E06
5.417,0.292 5.729,0.49 0.313,0.198 10 false IG 3.094,0.792 3.406,0.99 0.313,0.198 10 false DL1 3.438,0.792 3.594,0.99 0.156,0.198 10 false 6 3.094,1.26 3.552,1.458 0.458,0.198 10 false DL2 3.438,1.271 3.594,1.469 0.156,0.198 10 false 5 3.031,2.219 3.49,2.417 0.458,0.198 10 false ADD 3.438,2.24 3.594,2.438 0.156,0.198 10 false 3 1.688,2.51 3.26,2.729 1.573,0.219 10 false A.D.D. Position Switch 1.938,1.781 2.76,1.979 0.823,0.198 10 false Limit Switch 1.198,2.198 1.656,2.396 0.458,0.198 10 false GND 1.031,2.219 1.188,2.417 0.156,0.198 10 false 4 0.854,3.135 2.969,3.5 2.115,0.365 10 false A.D.D. Actuator (Differential Motor Actuator Assembly) 0.854,2.917 1.313,3.115 0.458,0.198 10 false C57 4.885,3.021 5.344,3.219 0.458,0.198 10 false C60 4.896,3.198 6.542,3.438 1.646,0.24 10 false 4 Wheel Drive Control ECU 4.958,0.802 5.417,1 0.458,0.198 10 false DL1 4.771,0.813 4.927,1.01 0.156,0.198 10 false 8 4.792,1.271 4.948,1.469 0.156,0.198 10 false 7 4.979,1.281 5.438,1.479 0.458,0.198 10 false DL2 4.969,2.219 5.427,2.417 0.458,0.198 10 false ADD 4.781,2.219 4.938,2.417 0.156,0.198 10 false 2 2.948,4.594 3.406,4.792 0.458,0.198 10 false EXI 2.25,4.042 2.563,4.24 0.313,0.198 10 false IG 3.323,4.688 3.635,4.885 0.313,0.198 10 false A3 3.688,4.688 4,4.885 0.313,0.198 10 false A4 3.74,4.458 3.896,4.656 0.156,0.198 10 false 3 3.323,4.458 3.635,4.656 0.313,0.198 10 false 31 3.344,4.927 3.656,5.125 0.313,0.198 10 false *1 3.708,4.917 4.021,5.115 0.313,0.198 10 false *2 0.948,5.323 3.813,5.531 2.865,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 5.083,4.917 6.771,5.115 1.688,0.198 10 false *1: w/o VSC 5.094,5.198 6.625,5.396 1.531,0.198 10 false *2: w/ VSC

C350245E01
0.26,0.698 1.344,1.563 1.083,0.865 10 false Skid Control ECU (Brake Actuator Assembly) 0.958,2.615 1.417,2.813 0.458,0.198 10 false ECM 2.323,0.26 2.781,0.458 0.458,0.198 10 false IG 2.26,0.729 3.188,0.958 0.927,0.229 10 false EXI2*1, EXI4*2 3.365,0.854 3.823,1.052 0.458,0.198 10 false A3 3.771,0.844 4.229,1.042 0.458,0.198 10 false A4 3.375,0.635 3.833,0.833 0.458,0.198 10 false 8 3.813,0.646 4.271,0.844 0.458,0.198 10 false 5 2.385,2.01 2.844,2.208 0.458,0.198 10 false +B 2.865,2.531 3.323,2.729 0.458,0.198 10 false L4 2.76,3.115 3.219,3.313 0.458,0.198 10 false 4WD 3.219,2.417 3.677,2.615 0.458,0.198 10 false 12 3.656,2.417 4.115,2.615 0.458,0.198 10 false 8 4.052,2.417 4.51,2.615 0.458,0.198 10 false 25 3.188,2.625 3.646,2.823 0.458,0.198 10 false C41 3.563,2.625 4.021,2.823 0.458,0.198 10 false G158 4.021,2.625 4.479,2.823 0.458,0.198 10 false G57 3.24,2.833 3.698,3.031 0.458,0.198 10 false *3 3.667,2.833 4.125,3.031 0.458,0.198 10 false *4 4.063,2.844 4.521,3.042 0.458,0.198 10 false *5 3.177,3.219 3.635,3.417 0.458,0.198 10 false G56 3.542,3.208 4,3.406 0.458,0.198 10 false G158 3.271,3 3.729,3.198 0.458,0.198 10 false 7 3.646,3 4.104,3.198 0.458,0.198 10 false 13 3.354,1.073 3.813,1.271 0.458,0.198 10 false *1 3.76,1.073 4.219,1.271 0.458,0.198 10 false *2 3.26,3.438 3.719,3.635 0.458,0.198 10 false *5 3.656,3.438 4.115,3.635 0.458,0.198 10 false *4 4.625,2.469 5.083,2.667 0.458,0.198 10 false *6 4.896,2.51 5.354,2.708 0.458,0.198 10 false 15 6.125,2.01 6.583,2.208 0.458,0.198 10 false +B 5.542,3.01 6,3.208 0.458,0.198 10 false G131 5.969,3.021 6.896,3.25 0.927,0.229 10 false TCM*6 5.135,2.51 5.594,2.708 0.458,0.198 10 false L4 5.021,4.052 5.479,4.25 0.458,0.198 10 false TL1 5.042,4.802 5.5,5 0.458,0.198 10 false TL2 5.042,5.469 5.5,5.667 0.458,0.198 10 false TL3 5.042,6.281 5.5,6.479 0.458,0.198 10 false 4WD 5.323,7.688 7.146,7.906 1.823,0.219 10 false 4 Wheel Drive Control ECU 4.771,4.042 5.229,4.24 0.458,0.198 10 false 11 4.771,4.792 5.229,4.99 0.458,0.198 10 false 10 4.813,5.469 5.271,5.667 0.458,0.198 10 false 9 4.833,6.281 5.292,6.479 0.458,0.198 10 false 1 4.813,6.99 5.271,7.188 0.458,0.198 10 false 3 4.969,7.688 5.427,7.885 0.458,0.198 10 false C60 5.052,6.99 5.51,7.188 0.458,0.198 10 false 4WDL 3.792,5.177 4.708,5.375 0.917,0.198 10 false *4, *5 3.479,4.031 3.938,4.229 0.458,0.198 10 false 3 3.469,4.781 3.927,4.979 0.458,0.198 10 false 4 3.479,5.479 3.938,5.677 0.458,0.198 10 false 5 3.469,6.281 3.927,6.479 0.458,0.198 10 false 12 3.49,7.01 3.948,7.208 0.458,0.198 10 false 9 3.208,7 3.667,7.198 0.458,0.198 10 false L4 3.125,5.479 3.583,5.677 0.458,0.198 10 false TL3 3.115,4.781 3.573,4.979 0.458,0.198 10 false TL2 3.125,4.042 3.583,4.24 0.458,0.198 10 false TL1 1.969,5.938 2.813,6.135 0.844,0.198 10 false Limit Switch 1.906,6.521 3.458,6.719 1.552,0.198 10 false 4WD Detection Switch 1.896,7.25 3.448,7.448 1.552,0.198 10 false L4 Detection Switch 3.219,6.281 3.677,6.479 0.458,0.198 10 false B 1.271,6.99 1.729,7.188 0.458,0.198 10 false GND 1.24,5.458 1.698,5.656 0.458,0.198 10 false GND1 1.01,5.458 1.469,5.656 0.458,0.198 10 false 6 1.01,6.99 1.469,7.188 0.458,0.198 10 false 10 1.198,7.792 1.656,7.99 0.458,0.198 10 false C63 1.521,7.792 3.938,8.031 2.417,0.24 10 false Transfer Shift Actuator Assembly 5.448,3.542 5.906,3.74 0.458,0.198 10 false IG 0.51,8.198 2.198,8.396 1.688,0.198 10 false *1: w/o VSC 0.521,8.479 2.208,8.677 1.688,0.198 10 false *2: w/ VSC 2.156,8.188 3.844,8.385 1.688,0.198 10 false *3: for 1GD-FTV 2.177,8.521 3.865,8.719 1.688,0.198 10 false *4: for 1GR-FE 3.854,8.198 5.542,8.396 1.688,0.198 10 false *5: for 2TR-FE 3.865,8.542 6.906,8.729 3.042,0.188 10 false *6: for 1KD-FTV (Automatic Transmission)

CAUTION / NOTICE / HINT

NOTICE:

When the vehicle is stopped, mode switching may be unavailable depending on the phase of the transfer assembly and A.D.D. actuator powertrain. There is no malfunction if mode switching is available after the vehicle is moved.


PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.


Result:
Result Proceed to
The 4WD indicator light (green) is blinking* A
The 4LO indicator light is blinking* B


*: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)



A

2.CHECK TRANSFER POSITION

B

7.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
2.CHECK TRANSFER POSITION
a.

Lift up the vehicle until all four wheels are off the ground.


b.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Move the shift lever to neutral.


c.

Turn the transfer position switch from H2 to H4.

HINT:

The 4WD indicator light (green) continues to blink*.

*: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




d.

Release the parking brake.


e.

Turn the ignition switch off.


f.

Disconnect the C63 transfer shift actuator assembly connector.


g.
C325774C03
1.865,1.958 2.24,2.688 false 1.479,1.958 1.167,2.667 false 1.833,1.552 1.698,0.896 false 1.5,1.552 1.198,0.906 false 1.229,1.552 0.719,0.927 false 0.927,1.958 0.542,2.604 false 0.927,1.563 0.427,1.292 false 0.198,0.271 0.51,0.469 0.313,0.198 10 false *a 1.021,2.688 1.479,2.885 0.458,0.198 10 false GND 2.219,2.729 2.531,2.927 0.313,0.198 10 false L4 0.51,0.708 0.969,0.906 0.458,0.198 10 false TL3 1.042,0.719 1.5,0.917 0.458,0.198 10 false TL2 1.604,0.729 2.063,0.927 0.458,0.198 10 false TL1 0.448,2.677 0.604,2.875 0.156,0.198 10 false B 0.125,1.104 0.594,1.281 0.469,0.177 10 false GND1
*a Component without harness connected
(Transfer Shift Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

HINT:

Check that the terminals of the limit switch, 4WD detection switch and L4 detection switch of the transfer shift actuator assembly (TL1, TL2, TL3, B and L4) are in the condition shown in the table below (H4).


Terminal When H4
TL1 OFF (OPEN)
TL2 OFF (OPEN)
TL3 ON (GND)
B ON (GND)
L4 OFF (OPEN)


Standard Resistance:
Tester Connection Condition Specified Condition
3 (TL1) - 6 (GND1) Transfer H4 10 kΩ or higher
4 (TL2) - 6 (GND1) 10 kΩ or higher
5 (TL3) - 6 (GND1) Below 1 Ω
12 (B) - 10 (GND) Below 1 Ω
9 (L4) - 10 (GND) 10 kΩ or higher


Result:
Result Proceed to
OK (H4 condition) A
NG (not H4 condition) B



A

3.CHECK DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (A.D.D. SHIFT MOTOR)

B

7.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
3.CHECK DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (A.D.D. SHIFT MOTOR)
a.
C290971C04
2.104,1.896 1.885,2.563 true 2.365,1.896 2.646,2.5 true 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 1.771,2.594 2.229,2.792 0.458,0.198 10 false DM2 2.563,2.531 3.021,2.729 0.458,0.198 10 false DM1
*a Component without harness connected
(A.D.D. Actuator (Differential Motor Actuator Assembly))


Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (DM1) - 2 (DM2) Always 1.5 to 10 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY)
a.

Disconnect the C61 4 wheel drive control ECU connector.


b.

Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C61-2 (DM1) - C57-1 (DM1) Always Below 1 Ω
C61-6 (DM2) - C57-2 (DM2) Always Below 1 Ω
C61-2 (DM1) or C57-1 (DM1) - C61-6 (DM2) or C57-2 (DM2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


c.

w/o VSC:

Disconnect the A3 skid control ECU (brake actuator assembly) connector.

w/ VSC:

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-8 (DL1) - C57-6 (DL1) Always Below 1 Ω
C60-7 (DL2) - C57-5 (DL2) Always Below 1 Ω
C60-2 (ADD) - C57-3 (ADD) Always Below 1 Ω
C57-4 (GND) - Body ground Always Below 1 Ω
C60-8 (DL1) or C57-6 (DL1) - Body ground Always 10 kΩ or higher
C60-7 (DL2) or C57-5 (DL2) - Body ground Always 10 kΩ or higher
C60-2 (ADD) or C57-3 (ADD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (LIMIT SWITCH AND A.D.D. POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (LIMIT SWITCH AND A.D.D. POSITION SWITCH)
a.

Turn the ignition switch off.


b.

Remove the A.D.D. actuator (differential motor actuator assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>REMOVAL


c.

Check the limit switch and A.D.D. position switch of the A.D.D. actuator (differential motor actuator assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

7.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
a.
C325774C04
2.688,0.781 2.333,1.563 false 2.01,1.563 1.563,0.854 false 0.198,0.271 0.51,0.469 0.313,0.198 10 false *a 1.385,0.656 1.844,0.854 0.458,0.198 10 false TM1 2.615,0.583 2.927,0.781 0.313,0.198 10 false TM2
*a Component without harness connected
(Transfer Shift Actuator Assembly)


Disconnect the C63 transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (TM1) - 1 (TM2) Always 1.5 to 10 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the C61 4 wheel drive control ECU connector.


b.

Disconnect the C63 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C61-8 (TM1) - C63-2 (TM1) Always Below 1 Ω
C61-7 (TM2) - C63- 1 (TM2) Always Below 1 Ω
C61-8 (TM1) or C63-2 (TM1) - C61-7 (TM2) or C63-1 (TM2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the C63 transfer shift actuator assembly connector.


c.

w/o VSC:

Disconnect the A3 skid control ECU (brake actuator assembly) connector.

w/ VSC:

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

for 1GD-FTV:

Disconnect the C41 ECM connector.

for 1GR-FE:

Disconnect the G158 ECM connector.

for 2TR-FE:

Disconnect the G56 and G57 ECM connectors.

for 1KD-FTV (Automatic Transmission):

Disconnect the G131 TCM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-11 (TL1) - C63-3 (TL1) Always Below 1 Ω
C60-10 (TL2) - C63-4 (TL2) Always Below 1 Ω
C60-9 (TL3) - C63-5 (TL3) Always Below 1 Ω
C63-6 (GND1) - Body ground Always Below 1 Ω
C60-1 (4WD) - C63-12 (B) Always Below 1 Ω
C60-3 (4WDL) - C63-9 (L4) Always Below 1 Ω
C63-10 (GND) - Body ground Always Below 1 Ω
C60-11 (TL1) or C63-3 (TL1) - Body ground Always 10 kΩ or higher
C60-10 (TL2) or C63-4 (TL2) - Body ground Always 10 kΩ or higher
C60-9 (TL3) or C63-5 (TL3) - Body ground Always 10 kΩ or higher
C60-1 (4WD) or C63-12 (B) - Body ground Always 10 kΩ or higher
C60-3 (4WDL) or C63-9 (L4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (LIMIT SWITCH AND 4WD DETECTION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (LIMIT SWITCH AND 4WD DETECTION SWITCH)
a.

Turn the ignition switch off.


b.

Remove the transfer shift actuator assembly.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY


c.

Check the limit switch, 4WD detection switch and L4 detection switch of the transfer shift actuator assembly.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY