Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM33K0E _52 Drivetrain _043529 VF2CM TRANSFER / 4WD / AWD _0227239 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17C8  Front Differential Oil Temperature Sensor Circuit High  


DESCRIPTION

This DTC is output when a short to B+ or open circuit in the oil temperature sensor is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17C8 Front Differential Oil Temperature Sensor Circuit High
·

Diagnosis Condition: Ignition switch turned to ON

·

Malfunction Status: Short to B+ or open circuit in the oil temperature sensor

·

Malfunction Time: 1 second or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Oil temperature sensor



PROCEDURE

1.CHECK OIL TEMPERATURE SENSOR
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.
C136763C01
1.49,0.635 1.875,0.896 0.385,0.26 1,1.698 0.552,0.865 true 1.031,1.927 0.615,2.698 true 1.563,0.677 2.021,0.875 0.458,0.198 10 false C60 0.417,0.708 0.729,0.906 0.313,0.198 10 false DT 0.344,2.74 0.958,2.938 0.615,0.198 10 false DGND 0.115,0.115 0.427,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-5 (DT) - C60-25 (DGND) Always 120 to 240 kΩ



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C60-5 (DT) or C60-25 (DGND) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - OIL TEMPERATURE SENSOR)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - OIL TEMPERATURE SENSOR)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the E1 oil temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-5 (DT) - E1-1 (DT) Always Below 1 Ω
C60-25 (DGND) - E1-2 (DGND) Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C60-5 (DT) or E1-1 (DT) - Body ground Ignition switch ON Below 1 V
C60-25 (DGND) or E1-2 (DGND) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR