Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock)
RM33K0E _52 Drivetrain _043595 AXLE AND DIFFERENTIAL _0227240 DIFFERENTIAL SYSTEM(w/ Differential Lock) D

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

When a DTC is stored, the 4 wheel drive control ECU stores the current vehicle state as Freeze Frame Data.

HINT:

Freeze Frame Data at the time a DTC is stored:

When the 4 wheel drive control ECU stores data at the time a DTC is stored, no updates will be performed until the data is cleared.




CHECK FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.

Powertrain > Four Wheel Drive > Trouble Codes
50001 363

f.

According to the display on the GTS, select the trouble code data display with Freeze Frame Data.

Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Rear Differential Lock Control SW (R) Differential lock switch status (differential lock switch input signal of R terminal on ECU side) ON or OFF ON: Switch pressed and held
OFF: Switch not pressed
-
Rear Differential Lock Detection SW (SLS) Rear differential lock position switch (No. 1 transfer indicator switch) status (rear differential lock position switch (No. 1 transfer indicator switch) input signal of SLS terminal on ECU side) ON or OFF ON: Rear differential locked condition
OFF: Rear differential free condition
-
IG SW Ignition switch status ON or OFF ON: Ignition switch ON -
Rear Differential Lock Solenoid Target Current Differential lock coil drive circuit target current value Min.: 0.0 A
Max.: 25.5 A
Rear differential locked: 1.0 to 8.0 A
Rear differential free: 0.1 A or less
-
Rear Differential Lock Solenoid Actual Current Differential lock coil drive circuit actual current value Min.: 0.0 A
Max.: 25.5 A
Rear differential locked: 1.0 to 8.0 A
Rear differential free: 0.1 A or less
-
Motor Energization Status Signal Motor power signal status ON or OFF ON: Power supplied to motor
OFF: Power not supplied to motor
-
C/C Cancel Request Cruise control cancellation signal status ON or OFF ON: Cruise control cancellation requested
OFF: Cruise control cancellation not requested
-
Rear Differential Lock Status Signal Rear differential LOCK status signal ON or OFF ON: Rear differential locked condition
OFF: Rear differential free condition
-
Buzzer Request Buzzer sounding request NO Sound, Sound(3 times) or Sound
·

NO Sound: Does not sound

·

Sound(3 times): Sounds 3 times

·

Sound: Sounds intermittently


·

Sounds 3 times: Sounds 3 times at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Sounds intermittently: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)


Rear Differential Lock Indicator Request Rear differential lock indicator light request Blink4*1, Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


Rear Differential Lock Solenoid Energization Request Differential lock coil power command ON or OFF ON: Power supplied to differential lock coil
OFF: Power not supplied to differential lock coil
-
IG Voltage IG monitor voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V: Ignition switch ON -
Rear Differential Lock Solenoid Voltage Differential lock coil drive circuit monitor voltage Min.: 0.0 V
Max.: 25.5 V
Rear differential locked: Higher than 3.5 V
Rear differential free: 3.5 V or less
-
Rear Differential Lock Solenoid Duty Differential lock coil drive circuit duty Min.: 0%
Max.: 255%
Rear differential locked: 0 to 100%
Rear differential free: 0%
-
Mode Status Mode transition condition Initial Control, Particular Control at Start-Up, Shift Settling Control at Start-Up, H2, H2->H4L(T/F Activating), H2->H4L(ADD Activating), H4L->H2(T/F Activating), H4L->H2(ADD Activating), H4L, H4L->L4L, L4L->H4L, L4L Rr Diff. Free, H4F->L4F, L4F->H4F, H4F, H4F->H4L, H4L->H4F, L4F, L4L Rr Diff. Free->Lock, L4L Rr Diff. Lock->Free, L4L Rr Diff. Lock, K1, K2, K3, K4, K5, K6, K7, K8, K9, K10, S01, S02, S03, S04, S05, S06, S07, S08, S09, S10, S11, S12, S13, S14, S15, S16, S17, S18, S19, S20, S21, S22, S23, S24, B1, B2, B3, B4, B5, B6, 2WD Rr Diff. Free, 2WD Rr Diff. Free->Lock, 2WD Rr Diff. Lock->Free or 2WD Rr Diff. Lock Displays transfer shift actuator*2, A.D.D. actuator*2 and differential lock coil transition condition
HINT:
·

K1 to K10: Control while switching prohibited

·

S01 to S24: Control while switching limited

·

B1 to B6: Control while switching again



Rear Differential Lock Solenoid Differential lock coil ECU internal power status ON or OFF ON: Power supplied
OFF: Power not supplied
-
CAN Signal Invalid Status by IG Voltage Low Whether CAN communication data is invalid due to IG voltage drop Valid or Inval Valid: IG voltage 9.5 V or higher Inval: IG voltage below 9.5 V
SW Input Invalid Status by IG Voltage Low Whether actuator switch input is invalid due to IG voltage drop Valid or Inval Valid: IG voltage 7.1 V or higher Inval: IG voltage below 7.1 V
Transfer Shift Invalid Status by IG Voltage Low Whether transfer shift actuator switching operation is invalid due to IG voltage drop Valid or Inval Valid: IG voltage 9.5 V or higher Inval: IG voltage below 9.5 V
Number of DTC Number of DTCs stored Min.: 0
Max.: 255
0 -

*1: Item not supported, therefore not displayed

*2: except Pre-Runner