Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM33K0E _56 Audio / Visual / Telematics _043543 PARK ASSIST / MONITORING _0227352 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives the reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E335901E01
3.344,0.927 3.802,1.125 0.458,0.198 10 false C11 3.354,1.104 4.698,1.469 1.344,0.365 10 false Park/Neutral Position Switch Assembly*3 5.74,1.198 6.198,1.396 0.458,0.198 10 false G88 5.771,1.375 6.948,1.76 1.177,0.385 10 false Clearance Warning ECU Assembly 4.333,0.5 4.646,0.698 0.313,0.198 10 false RL 3.604,0.49 3.917,0.688 0.313,0.198 10 false RB 3.333,2.719 4.677,3.052 1.344,0.333 10 false Back-up Light Switch Assembly*4 3.344,2.542 3.802,2.74 0.458,0.198 10 false C22 2.042,0.771 3.271,0.969 1.229,0.198 10 false IG1 NO.1 0.115,0.604 2.563,0.802 2.448,0.198 10 false from IG1 NO.1 Relay*1 6.021,0.604 6.333,0.802 0.313,0.198 10 false RL 5.729,0.479 6.042,0.677 0.313,0.198 10 false 21 4.635,0.49 4.792,0.688 0.156,0.198 10 false 1 3.365,0.479 3.521,0.677 0.156,0.198 10 false 2 3.323,2.094 3.479,2.292 0.156,0.198 10 false 2 4.615,2.094 4.771,2.292 0.156,0.198 10 false 1 0.156,1.083 3.521,1.281 3.365,0.198 10 false from Ignition Switch*2 0.063,2.333 5.417,2.531 5.354,0.198 10 false *1: w/ Smart Entry and Start System 0.063,2.667 5.417,2.865 5.354,0.198 10 false *2: w/o Smart Entry and Start System 0.073,3.021 5.427,3.219 5.354,0.198 10 false *3: for Automatic Transmission 0.083,3.375 5.438,3.573 5.354,0.198 10 false *4: for Manual Transmission 5.083,2.365 5.396,2.563 0.313,0.198 10 false *4 1.708,0.729 2.021,0.927 0.313,0.198 10 false *1 1.698,1.24 2.01,1.438 0.313,0.198 10 false *2 5.042,0.729 5.354,0.927 0.313,0.198 10 false *3 2.813,2.385 3.125,2.583 0.313,0.198 10 false *4 2.875,0.75 3.188,0.948 0.313,0.198 10 false *3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.
B409698C01
0.167,1.063 0.667,1.313 0.5,0.25 0.875,1.906 1.208,1.906 1.208,1.906 1.406,1.292 true 0.271,1.104 0.729,1.302 0.458,0.198 10 false G88 0.063,0.031 0.521,0.229 0.458,0.198 10 false *a 0.656,1.823 1.115,2.021 0.458,0.198 10 false RL
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G88-21 (RL) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V
G88-21 (RL) - Body ground
·

Ignition switch ON

·

Shift lever in any position other than R


Below 1 V



Result:
Result Proceed to
OK A
NG (for Manual Transmission) B
NG (for Automatic Transmission) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

C

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
a.

Remove the back-up light switch assembly.

Click hereDrivetrain>RC61F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL


b.

Inspect the back-up light switch assembly.

Click hereDrivetrain>RC61F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the C11 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-21 (RL) - C11-1 Always Below 1 Ω
G88-21 (RL) or C11-1 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C11-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

A

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

B

C

D

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the C22 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-21 (RL) - C22-1 (RL) Always Below 1 Ω
G88-21 (RL) or C22-1 (RL) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-2 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR