In this circuit, the combination meter assembly receives engine speed signals from the ECM via the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.
When replacing the combination meter assembly, make sure to replace it with a new one.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
Check for DTCs.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK (for Diesel Engine) | A |
| OK (for Gasoline Engine) | B |
| NG | C |
A
B
C
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>DTC CHECK / CLEAR
for 1GD-FTV, w/ DPF: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>DTC CHECK / CLEAR
for 1GD-FTV, for i-ART: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GD-FTV, w/ DPF: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GD-FTV, for i-ART: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>HOW TO PROCEED WITH TROUBLESHOOTING
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, perform the Active Test.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| TachoMeter Operation | Tachometer | OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000*1 or 7000*2 (rpm) | *1: for Gasoline Engine
*2: for 2TR-FE |
| Tester Display |
|---|
| TachoMeter Operation |
Tachometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383.75 rpm | Actual engine speed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Rpm | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine Speed |
| Tester Display |
|---|
| Engine Rpm |
When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.
When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
The Data List values of the ECUs do not match.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
Replace the combination meter assembly with a new one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Check that the operation of the tachometer returns to normal.
The operation of the tachometer returns to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
Check for DTCs.
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING