Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)
RM33K0E _52 Drivetrain _043594 DRIVE SHAFT / PROPELLER SHAFT _0229191 FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for both universal joint spider assemblies.


a.
C258225

Apply grease to a new spider and new spider bearings.

Grease:

Lithium base chassis grease NLGI No. 2


NOTICE:

Do not apply too much grease.



b.

Install the spider to the flange yoke.


c.
C317894C01
1.083,0.917 1.083,0.167 1.083,0.167 1.25,0.167 true 2.5,1 3.167,1 true 1.688,1.656 2,1.854 0.313,0.198 10 false *a 0.063,1.229 0.375,1.427 0.313,0.198 10 false *b 1.292,0.083 1.75,0.281 0.458,0.198 10 false SST 3.219,0.927 3.396,1.229 0.177,0.302 10 false A
*a Turn
*b Hold


Using SST, install 2 of the spider bearings to the universal joint spider assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



d.

Using SST, adjust both spider bearings so that the snap ring grooves are as wide as possible and equal in width.

SST
09332-25010  


e.
F052434

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

NOTICE:

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.


HINT:

Do not reuse the snap rings.


Standard Snap Ring Thickness:
Part No. Color Thickness
90080-52044 Green 1.384 mm (0.0545 in.)
90080-52174 Green 1.39 mm (0.0547 in.)
90080-52043 Red 1.435 mm (0.0565 in.)
90080-52175 Orange 1.44 mm (0.0567 in.)
90080-52041 Black 1.486 mm (0.0585 in.)
90080-52176 Black 1.49 mm (0.0587 in.)
90080-52042 Copper 1.511 mm (0.0595 in.)
90080-52040 Silver 1.537 mm (0.0605 in.)
90080-52177 White 1.54 mm (0.0606 in.)
90080-52039 Yellow 1.588 mm (0.0625 in.)
90080-52178 Yellow 1.59 mm (0.0626 in.)
90080-52038 Blue 1.638 mm (0.0645 in.)
90080-52179 Red 1.64 mm (0.0646 in.)
90080-52180 Blue 1.69 mm (0.0665 in.)


NOTICE:
·

Use a new snap ring.

·

Use a snap ring with as close to the same thickness as possible on both ends.




f.
C282524C01
2.365,0.656 1.656,0.302 1.656,0.302 1.333,0.302 true 1.115,0.198 1.427,0.354 0.313,0.156 10 false *a
*a Hammering Point


Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



g.

Align the matchmarks on the flange yoke and front propeller shaft assembly.


h.
C307744C01
1.167,1 1.167,0.417 1.167,0.417 1.25,0.417 true 2.5,1.333 2.865,1.323 true 1.323,1.573 1.635,1.771 0.313,0.198 10 false *a 0.979,0.125 1.292,0.323 0.313,0.198 10 false *b 1.292,0.333 1.75,0.531 0.458,0.198 10 false SST 2.948,1.25 3.167,1.469 0.219,0.219 10 false A
*a Turn
*b Hold


Using SST, install the 2 spider bearings to the universal joint spider assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



i.

Using SST, adjust both spider bearings so that the snap ring grooves are as wide as possible and equal in width.

SST
09332-25010  


j.

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

NOTICE:

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.


HINT:

Do not reuse the snap rings.


Standard Snap Ring Thickness:
Part No. Color Thickness
90080-52044 Green 1.384 mm (0.0545 in.)
90080-52174 Green 1.39 mm (0.0547 in.)
90080-52043 Red 1.435 mm (0.0565 in.)
90080-52175 Orange 1.44 mm (0.0567 in.)
90080-52041 Black 1.486 mm (0.0585 in.)
90080-52176 Black 1.49 mm (0.0587 in.)
90080-52042 Copper 1.511 mm (0.0595 in.)
90080-52040 Silver 1.537 mm (0.0605 in.)
90080-52177 White 1.54 mm (0.0606 in.)
90080-52039 Yellow 1.588 mm (0.0625 in.)
90080-52178 Yellow 1.59 mm (0.0626 in.)
90080-52038 Blue 1.638 mm (0.0645 in.)
90080-52179 Red 1.64 mm (0.0646 in.)
90080-52180 Blue 1.69 mm (0.0665 in.)


NOTICE:
·

Use a new snap ring.

·

Use snap rings with as close to the same thickness as possible on both ends.




k.
C258229C01
1.646,2.031 1.896,2.031 1.896,2.031 2.344,1.792 false 1.458,1.938 1.667,2.125 0.208,0.188 10 *a
*a Hammering Point


Using a hammer, tap the front propeller shaft assembly until there is no clearance between the spider bearing outer race and snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



Hide 37334A 2.INSTALL SLIDING SHAFT BOOT

a.
C346193C01
2.667,1.5 2.75,1 2.75,1 2.917,1 true 1.833,1.5 1.417,0.833 1.417,0.833 1.25,0.833 true 1.833,1.667 1.417,2.25 1.417,2.25 1.25,2.25 true 2.667,1.667 2.833,2.167 2.833,2.167 3,2.167 true 2.5,1.5 2.667,0.667 2.667,0.667 2.833,0.667 true 1.979,1.417 2.146,0.25 2.146,0.25 2.313,0.25 true 2.25,1.417 2.5,0.417 2.5,0.417 2.667,0.417 true 2.417,2.333 2.417,2.25 2.417,2.25 1.833,2.25 true 3,0.917 3.313,1.115 0.313,0.198 10 false *b 1.021,0.75 1.333,0.948 0.313,0.198 10 false *b 1.021,2.167 1.333,2.365 0.313,0.198 10 false *a 3.083,2.083 3.333,2.365 0.25,0.281 10 false *a 2.917,0.583 3.229,0.781 0.313,0.198 10 false *1 2.354,0.167 2.667,0.365 0.313,0.198 10 false *1 2.771,0.333 3.083,0.531 0.313,0.198 10 false *2 1.583,2.167 1.833,2.448 0.25,0.281 10 false *c
*1 Propeller Shaft Boot Clamp
*2 Sliding Shaft Boot
*a Matchmark of Front Propeller Shaft Assembly and Sleeve Yoke
*b Matchmark of Pinching Portion of Propeller Shaft Boot Clamp
*c Pinching Portion


Temporarily install a new sliding shaft boot to the front propeller shaft assembly with 2 new propeller shaft boot clamps.


b.

Coat the splines of the front propeller shaft assembly with MP grease.

Standard Grease Capacity:

7.0 to 10.0 g (0.25 to 0.35 oz)



c.

Align the matchmarks on the front propeller shaft assembly and sleeve yoke.


d.

Install the sleeve yoke to the front propeller shaft assembly and connect the sliding shaft boot.


e.

Align the matchmarks on the front propeller shaft assembly, sleeve yoke and the pinching portions of the 2 propeller shaft boot clamps.

HINT:

Make sure to align the matchmarks of the propeller shaft boot clamp.


If the pinching portions are installed at different locations than where they were located before disassembly, the rotational balance of the front propeller shaft assembly cannot be ensured, which may result in vibrations and noise.


f.
C346180C01
2.771,1.771 2.594,1.771 2.594,1.771 2,1 true 2.958,0.854 3.271,1.052 0.313,0.198 10 false *a 1.677,0.542 1.99,0.74 0.313,0.198 10 false *b 2.823,1.677 3.271,1.927 0.448,0.25 10 false SST
*a Turn
*b Hold


Secure one of the propeller shaft boot clamps to the sliding shaft boot.

HINT:
·

Use the same procedure for each propeller shaft boot clamp.

·

Make sure that the matchmarks of the pinching portion of the propeller shaft boot clamp are aligned.



i.

Install SST to the propeller shaft boot clamp, and then while pressing the sliding shaft boot, slightly tighten the SST bolt.

SST
09521-24010  

NOTICE:
·

Correctly set the propeller shaft boot clamp to the guide groove.

·

Do not damage the sliding shaft boot.




ii.

Tighten SST so that the propeller shaft boot clamp is pinched.

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:
·

When tightening SST, make sure the clearance of the propeller shaft boot clamp is within the standard clearance.

·

Do not damage the sliding shaft boot.




iii.

Remove SST from the propeller shaft boot clamp.


iv.
C118611N01
1.906,1.052 2.938,1.531 true 3,1.51 3.323,1.677 0.323,0.167 10 false SST

Using SST, measure the clearance of the propeller shaft boot clamp.

SST
09240-00020  

Standard clearance:

0.8 mm (0.0314 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the propeller shaft boot clamp.




Hide 3.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with grease.

Grease:

Lithium base chassis grease NLGI No. 2




C346194C01
0.76,1.417 0.76,0.25 0.76,0.25 0.927,0.25 true 4.625,1.354 4.625,0.604 4.625,0.604 4.792,0.604 true 1.021,0.177 1.333,0.375 0.313,0.198 10 false *a 4.833,0.531 5.146,0.729 0.313,0.198 10 false *b 5.573,0.865 5.885,1.063 0.313,0.198 10 false *b 5.552,1.75 5.865,1.948 0.313,0.198 10 false *a 2.656,0.635 2.969,0.833 0.313,0.198 10 false *c
*a No. 1 Grease Fitting *b No. 2 Grease Fitting
*c Vehicle Rear - -