Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW MASTER SWITCH
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229932 POWER WINDOW MASTER SWITCH G

WINDOW / GLASS  POWER WINDOW MASTER SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
B437152C02
2.417,0.99 2.833,0.99 true 2.104,0.958 2.656,0.479 true 1.917,0.938 2.177,0.323 true 1.625,0.948 1.51,0.313 true 1.458,0.927 0.844,0.396 true 2.417,1.24 2.802,1.563 true 2.083,1.271 2.49,1.771 true 1.917,1.281 1.938,1.802 true 1.583,1.281 1.417,1.802 true 1.417,1.281 0.948,1.813 true 1.083,1.271 0.667,1.583 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a 2.875,0.927 3.031,1.125 0.156,0.198 10 false E 2.719,0.365 2.875,0.563 0.156,0.198 10 false D 2.156,0.115 2.313,0.313 0.156,0.198 10 false A 1.438,0.073 1.594,0.271 0.156,0.198 10 false U 0.719,0.281 0.875,0.479 0.156,0.198 10 false B 2.885,1.563 3.042,1.76 0.156,0.198 10 false U 2.563,1.802 2.719,2 0.156,0.198 10 false U 1.927,1.854 2.083,2.052 0.156,0.198 10 false D 1.344,1.875 1.5,2.073 0.156,0.198 10 false U 0.823,1.833 0.979,2.031 0.156,0.198 10 false D 0.479,1.563 0.635,1.76 0.156,0.198 10 false D
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (E) - 4 (A)
4 (A) - 6 (U)
3 (D) - 7 (B)
Auto UP (for driver door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 6 (U)
3 (D) - 7 (B)
Manual UP (for driver door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 3 (D)
6 (U) - 7 (B)
Manual DOWN (for driver door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 3 (D)
3 (D) - 4 (A)
6 (U) - 7 (B)
Auto DOWN (for driver door) Below 1 Ω
Not operated 10 kΩ or higher
3 (D) - 6 (U)
6 (U) - 7 (B)
OFF (for driver door) Below 1 Ω
1 (E) - 18 (D)
7 (B) - 10 (U)
Manual UP (for front passenger door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 10 (U)
7 (B) - 18 (D)
Manual DOWN (for front passenger door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 10 (U)
10 (U) - 18 (D)
OFF (for front passenger door) Below 1 Ω
1 (E) - 16 (D)
7 (B) - 15 (U)
Manual UP (for rear RH door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 15 (U)
7 (B) - 16 (D)
Manual DOWN (for rear RH door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 15 (U)
15 (U) - 16 (D)
OFF (for rear RH door) Below 1 Ω
1 (E) - 13 (D)
7 (B) - 12 (U)
Manual UP (for rear LH door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 12 (U)
7 (B) - 13 (D)
Manual DOWN (for rear LH door) Below 1 Ω
Not operated 10 kΩ or higher
1 (E) - 12 (U)
12 (U) - 13 (D)
OFF (for rear LH door) Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



c.

Check that the LED illuminates.

i.
B437152C01
2.313,0.271 1.771,0.979 true 1.302,1.26 1,1.802 true 2.385,0.135 3,0.333 0.615,0.198 10 false ILL- 0.844,1.802 1.458,2 0.615,0.198 10 false ILL+ 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 17 (ILL+)
Battery negative (-) → 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



Hide 84820 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Smart Entry and Start System)

a.
B129570C23
2.26,0.969 2.781,0.25 true 2.26,1.344 2.771,1.854 true 2.844,0.135 3.198,0.313 0.354,0.177 10 false ILL+ 2.823,1.781 3.135,2 0.313,0.219 10 false ILL- 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Check that the LED illuminates.

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (ILL+)
Battery negative (-) → 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.