Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0230461 REAR SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR SPEED SENSOR (for Rear Disc Brake)

a.

for RH:

C329858

i.

Install the rear speed sensor RH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Attach the 8 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



iii.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





b.

for LH:

C329857

i.

Install the rear speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Attach the 3 clamps.

NOTICE:

When attaching the clamp, do not twist the wire harness.



iii.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





Hide 2.INSTALL REAR SPEED SENSOR (for Rear Drum Brake)

a.

for RH:

C329856

i.

Install the rear speed sensor RH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Attach the 8 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



iii.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





b.

for LH:

C329855

i.

Install the rear speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Attach the 3 clamps.

NOTICE:

When attaching the clamp, do not twist the wire harness.



iii.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.