Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P1605  Rough Idling  


DESCRIPTION

This DTC is stored if the combustion state of any cylinder is unstable.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling When idling with the accelerator pedal released and the vehicle stopped, this item detects when the combustion is unstable from the sudden changes in engine speed between the cylinders. Detection for 2 to 10 seconds according to the combustion state. (1 trip detection logic).
·

Injector assembly

·

Fuel leak

·

Glow system

·

Intake air system leakage

·

Intake system blockage

·

EGR system

·

Throttle valve system

·

Pre-stroke control valve

·

Low quality fuel

·

Fuel filter element assembly air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

Engine assembly

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P1605
·

Target Idle Engine Speed

·

Engine Speed

·

MAP

·

MAF

·

Coolant Temp

·

Battery Voltage

·

Engine Speed of Cyl #1 (to #4)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Intake Air

·

Target Common Rail Pressure

·

Common Rail Pressure

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Valve Pos

·

Actual EGR Valve Pos

·

EGR Close Lrn. Val.

·

Rough Idle #1 (to #4)

·

Plural Cylinders Rough Idle

·

Injector Leaking Count #1 (to #4)

·

i-ART Learning Status History #1 (to #4)



CAUTION / NOTICE / HINT

In order for idling to be stable, glow system operation, fuel system operation and compression sufficient to maintain the target idling speed are necessary.



Glow system


a.

The following malfunctions may be present in the glow system.

i.

Engine coolant temperature sensor malfunction.


ii.

Glow plug malfunction.


iii.

Glow plug controller malfunction.




Fuel system


a.

The following malfunctions may be present in the fuel system.

i.

Fuel leakage.


ii.

Problem with injector assemblies.


iii.

Problem with fuel supply pump assembly.


iv.

Air in fuel pipe.




Engine assembly


a.

The following malfunctions may be present in the engine assembly.

i.

Insufficient compression.




HINT:
·

In contrast to conventional DTCs for components, circuits and systems, DTC P1605 is used to estimate the malfunctioning area from problem symptoms and freeze frame data in response to symptoms such as "rough idling", "strong engine vibrations", etc. Such problem symptoms can occur even in the following conditions:

·

Driving with long-stored fuel (fuel that has remained in the tank for long periods of time)

·

Using fuel not acclimated to the climate during a change of seasons

·

Temporarily using low-quality fuel (fuel that contains water or has poor fuel properties)


·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.



PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 234
HINT:

This freeze frame data shows the actual engine conditions when air fuel ratio too rich trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
P1605 is output A
P1605 and other DTCs are output B


HINT:

If any DTCs other than P1605 are output, troubleshoot those DTCs first.




A

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA)

B

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA)
a.

Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.

Rough Idle #1 to #4:
Judgment of Data List Values Problem Cause Diagnosis Note Proceed to
Any of Rough Idle #1 to #4 in the freeze frame data is ON Injector assembly If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected.
HINT:

When there are temporary changes in the injection characteristics, the malfunction may not be indicated by the value for Injection Feedback Val in the freeze frame data.


A


Injection Feedback Val #1(to #4):
Judgment of Data List Values Problem Cause Diagnosis Note Proceed to
Any of Injection Feedback Val #1 to #4 in the freeze frame data is more than 3.0 mm3/st Injector assembly If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected. A


Injector Leaking Count #1 (to #4):
Judgment of Data List Values Problem Cause Diagnosis Note Proceed to
Any values for "Injector Leaking Count #1 to #4" in the Freeze Frame Data display 1 or more
·

Foreign matter trapped inside injector

·

Fuel filter element assembly

·

Irregular fuel


When the counter is 1 or more, the problem may have occurred due to foreign matter in the fuel system.
Replace the fuel filter element assembly, etc. and perform repairs according to the troubleshooting procedure.
A


i-ART Learning Status History #1 (to #4):
Judgment of Data List Values Problem Cause Diagnosis Note Proceed to
Any values for "i-ART Learning Status History #1 to #4" in the Freeze Frame Data display 1 Trip or more
·

Injector assembly

·

Irregular fuel


When the counter is 1 or more, the problem may have occurred due to foreign matter in the fuel system.
Replace the fuel filter element assembly, etc. and perform repairs according to the troubleshooting procedure.
A


Plural Cylinders Rough Idle:
Judgment of Data List Values Problem Cause Diagnosis Note Proceed to
Plural Cylinders Rough Idle in the freeze frame data is ON
·

EGR system

·

Diesel throttle system

·

Fuel supply pump assembly

·

Low-quality fuel


When EGR Rate Differential (Actual-Target) increases by more than 30%, there may be a malfunction in the EGR system. B
When there is data stored that indicates that Common Rail Pressure is low compared to Target Common Rail Pressure, there may be a malfunction in the fuel pressure control system, such as in the fuel supply pump assembly. C
When data indicating that MAP is low (50 kPa or less) is stored, there may be a stuck closed malfunction in the diesel throttle system or EGR valve. -




A

GO TO CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

B

GO TO CHECK DATA LIST (ACTUAL EGR VALVE/TARGET EGR VALVE DIFFERENTIAL) (ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS)

C

GO TO CHECK DATA LIST (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE) (ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS)