Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P168A  Injector #1 Internal EEPROM Malfunction  P168B  Injector #2 Internal EEPROM Malfunction  P168C  Injector #3 Internal EEPROM Malfunction  P168D  Injector #4 Internal EEPROM Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P168A Injector #1 Internal EEPROM Malfunction The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic)
No. 1 injector assembly - DTC stored
P168B Injector #2 Internal EEPROM Malfunction The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic)
No. 2 injector assembly - DTC stored
P168C Injector #3 Internal EEPROM Malfunction The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic)
No. 3 injector assembly - DTC stored
P168D Injector #4 Internal EEPROM Malfunction The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic)
No. 4 injector assembly - DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P168A
P168B
P168C
P168D
Engine switch on (IG) for 3 minutes or more

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) for 3 minutes or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
DTC P168A, P168B, P168C and/or P168D is output A
No DTC is output B




A

2.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

B

2.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

3.BLEED AIR FROM FUEL SYSTEM
3.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) for 3 minutes or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END