Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › from 2016.07
RM33K0E _57 Power Source / Network _043546 NETWORKING _0227039 CAN COMMUNICATION SYSTEM(for LHD) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 1 CAN Junction Connector

C346324C01
5.26,3.594 5.49,3.385 5.49,3.385 5.656,3.385 true 5.25,3.75 5.479,3.979 5.479,3.979 5.646,3.979 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *1 4.24,2.979 4.552,3.177 0.313,0.198 10 false *a 5.688,3.271 6.167,3.5 0.479,0.229 10 false CANH 5.688,3.865 6.167,4.094 0.479,0.229 10 false CANL 1.833,2.49 2.313,2.719 0.479,0.229 10 false G123 1.885,4.052 2.365,4.281 0.479,0.229 10 false G93 1.885,3.813 2.365,4.042 0.479,0.229 10 false G94 1.885,3.594 2.365,3.823 0.479,0.229 10 false G95 1.885,3.375 2.365,3.604 0.479,0.229 10 false G96 1.854,3.146 2.333,3.375 0.479,0.229 10 false G128 1.875,2.938 2.354,3.167 0.479,0.229 10 false G98 1.885,2.708 2.365,2.938 0.479,0.229 10 false G99
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


No. 1 CAN Junction Connector Wiring Color Connect to

*1: for LED Headlight

*2: w/ Smart Entry and Start System

*3: w/ Back Door Closer System

*4: w/ VSC

G93-1 (CANH) B Brake actuator assembly (skid control ECU)
G93-2 (CANL) W
G94-1 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)*4
G94-2 (CANL) W
G95-1 (CANH) L DLC3
G95-2 (CANL) W
G96-1 (CANH) P Combination meter assembly
G96-2 (CANL) W
G98-1 (CANH) V Headlight leveling ECU assembly*1
G98-2 (CANL) W
G99-1 (CANH) G Certification ECU (smart key ECU assembly)*2
G99-2 (CANL) W
G123-1 (CANH) LG No. 2 CAN junction connector
G123-2 (CANL) W
G128-1 (CANH) SB Multiplex network door ECU*3
G128-2 (CANL) W


b.

No. 2 CAN Junction Connector

C349914C01
5.25,3.573 5.51,3.344 5.51,3.344 5.656,3.344 true 5.26,3.75 5.49,4.073 5.49,4.073 5.635,4.073 true 0.052,0.115 0.365,0.271 0.313,0.156 10 false *1 4.25,2.99 4.563,3.146 0.313,0.156 10 false *a 1.833,3.813 2.313,4.031 0.479,0.219 10 false G120 1.844,3.594 2.323,3.813 0.479,0.219 10 false G121 1.854,3.365 2.333,3.583 0.479,0.219 10 false G126 1.844,3.146 2.323,3.365 0.479,0.219 10 false G125 1.896,2.927 2.375,3.146 0.479,0.219 10 false G97 1.865,2.708 2.344,2.927 0.479,0.219 10 false G122 5.698,3.229 6.177,3.448 0.479,0.219 10 false CANH 5.688,3.969 6.167,4.188 0.479,0.219 10 false CANL
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
- -


No. 2 CAN Junction Connector Wiring Color Connect to

*1: for 4WD

*2: w/ Navigation System

*3: w/ Audio and Visual System (for Radio and Display Type)

G97-1 (CANH) LG No. 1 CAN junction connector
G97-2 (CANL) W
G120-1 (CANH) Y Airbag sensor assembly
G120-2 (CANL) W
G121-1 (CANH) GR Air conditioning amplifier assembly
G121-2 (CANL) W
G122-1 (CANH) B ECM
G122-2 (CANL) W
G125-1 (CANH) R 4 wheel drive control ECU*1
G125-2 (CANL) W
G126-1 (CANH) V
·

Navigation receiver assembly*2

·

Radio and display receiver assembly*3


G126-2 (CANL) W



CHECK DLC3


a.
C253362C14
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.292,1.052 0.75,1.25 0.458,0.198 10 false G7 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G7-6 (CANH) - G7-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G7-6 (CANH) - G7-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G7-14 (CANL) - G7-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G7-6 (CANH) - G7-16 (BAT) L - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G7-14 (CANL) - G7-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2TR-FE, 2TR-FBE)


C317085E01
1,0.531 1.427,0.792 0.427,0.26 2.125,0.521 2.552,0.781 0.427,0.26 3.292,0.521 3.719,0.781 0.427,0.26 4.344,0.521 4.771,0.781 0.427,0.26 5.49,0.521 5.917,0.781 0.427,0.26 5.865,1.135 6.219,0.813 6.219,0.813 6.354,0.813 true 4.792,2.198 4.646,2.198 4.646,2.198 4.406,1.333 true 3.854,2.177 4.021,2.177 4.021,2.177 4.302,1.354 true 0.49,0.865 0.635,0.865 0.635,0.865 1.302,1.146 true 1.094,0.594 1.552,0.792 0.458,0.198 10 false C14 2.229,0.583 2.688,0.781 0.458,0.198 10 false C15 3.385,0.573 3.844,0.771 0.458,0.198 10 false C16 4.438,0.573 4.896,0.771 0.458,0.198 10 false G56 5.594,0.573 6.052,0.771 0.458,0.198 10 false G57 6.427,0.74 7.042,0.938 0.615,0.198 10 false BATT 0.26,0.792 0.875,0.99 0.615,0.198 10 false E1 4.875,2.115 5.49,2.313 0.615,0.198 10 false CANH 3.458,2.104 4.073,2.302 0.615,0.198 10 false CANL

a.

Disconnect the ECM connectors.

C317087C01
0.875,0.51 1.302,0.771 0.427,0.26 3.375,0.521 3.802,0.781 0.427,0.26 5.917,0.531 6.344,0.792 0.427,0.26 0.542,0.875 0.677,0.875 0.677,0.875 0.896,1.396 true 4.354,0.906 4.219,0.906 4.219,0.906 3.948,1.563 true 3.031,0.875 3.167,0.875 3.167,0.875 3.833,1.573 true 5.531,0.906 5.667,0.906 5.667,0.906 5.969,1.385 true 0.958,0.552 1.417,0.75 0.458,0.198 10 false G57 3.469,0.573 3.927,0.771 0.458,0.198 10 false G56 6.01,0.573 6.469,0.771 0.458,0.198 10 false C14 2.604,0.802 3.219,1 0.615,0.198 10 false CANH 4.448,0.813 5.063,1.01 0.615,0.198 10 false CANL 0.167,0.802 0.781,1 0.615,0.198 10 false BATT 5.313,0.833 5.927,1.031 0.615,0.198 10 false E1 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G56-13 (CANH) - G56-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G56-13 (CANH) - C14-3 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-14 (CANL) - C14-3 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-13 (CANH) - G57-3 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G56-14 (CANL) - G57-3 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 1GD-FTV)


A340466E03
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 3.906,2.125 4.052,2.125 4.052,2.125 4.51,1.198 true 6.344,2.104 6.5,2.104 6.5,2.104 6.74,1.219 true 4.979,2.031 5.125,2.031 5.125,2.031 5.667,1.49 true 5.302,2.375 5.448,2.375 5.448,2.375 5.698,1.646 true 1.833,0.469 2.146,0.667 0.313,0.198 10 false C39 0.615,0.469 0.927,0.667 0.313,0.198 10 false C38 2.938,0.469 3.25,0.667 0.313,0.198 10 false C40 3.979,0.469 4.292,0.667 0.313,0.198 10 false C41 5.094,0.469 5.406,0.667 0.313,0.198 10 false G49 6.26,0.469 6.573,0.667 0.313,0.198 10 false G50 5.948,2.031 6.333,2.229 0.385,0.198 10 false BATT 3.667,2.052 3.917,2.26 0.25,0.208 10 false E1 4.552,1.958 4.979,2.146 0.427,0.188 10 false CANH 4.865,2.302 5.302,2.49 0.438,0.188 10 false CANL

a.

Disconnect the ECM connectors.

C317088C01
1,0.448 1.448,0.719 0.448,0.271 3.25,0.438 3.698,0.708 0.448,0.271 5.552,0.406 6,0.677 0.448,0.271 0.521,0.896 0.656,0.896 0.656,0.896 0.698,1.396 true 2.667,0.979 2.802,0.979 2.802,0.979 2.927,1.688 true 4.917,0.865 5.052,0.865 5.052,0.865 5.219,1.406 true 2.625,2.323 2.76,2.323 2.76,2.323 2.927,1.906 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.094,0.51 1.552,0.708 0.458,0.198 10 false G50 3.333,0.49 3.792,0.688 0.458,0.198 10 false G49 5.656,0.469 6.115,0.667 0.458,0.198 10 false C41 0.125,0.823 0.531,1.031 0.406,0.208 10 false BATT 4.677,0.781 4.958,0.969 0.281,0.188 10 false E1 2.219,0.906 2.625,1.115 0.406,0.208 10 false CANH 2.219,2.25 2.625,2.458 0.406,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G49-17 (CANH) - G49-28 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G49-17 (CANH) - C41-1 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G49-28 (CANL) - C41-1 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G49-17 (CANH) - G50-1 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G49-28 (CANL) - G50-1 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 1KD-FTV)


C317086E04
1.521,0.51 1.979,0.781 0.458,0.271 2.677,0.51 3.135,0.781 0.458,0.271 3.896,0.51 4.354,0.781 0.458,0.271 5,0.51 5.458,0.781 0.458,0.271 1.5,2.156 1.677,2.156 1.677,2.156 2.417,1.177 true 5.292,2.135 5.177,2.135 5.177,2.135 4.344,1.198 true 3.531,2.135 3.708,2.135 3.708,2.135 3.896,1.49 true 4.365,2.167 4.25,2.167 4.25,2.167 4.021,1.49 true 1.646,0.563 2.104,0.76 0.458,0.198 10 false C73 2.792,0.552 3.25,0.75 0.458,0.198 10 false C74 3.958,0.552 4.417,0.75 0.458,0.198 10 false G129 5.063,0.552 5.521,0.75 0.458,0.198 10 false G130 3.125,2.073 3.74,2.271 0.615,0.198 10 false CANH 4.427,2.083 5.042,2.281 0.615,0.198 10 false CANL 5.354,2.052 5.969,2.25 0.615,0.198 10 false BATT 1.281,2.083 1.896,2.281 0.615,0.198 10 false E1

a.

Disconnect the ECM connectors.

C329287C02
5.063,0.24 5.521,0.552 0.458,0.313 1.677,0.229 2.24,0.51 0.563,0.281 5.896,1.135 6.073,0.667 6.073,0.667 6.208,0.667 true 1.135,0.719 1.26,0.719 1.26,0.719 1.656,1.115 true 2.188,1.469 2.458,2.208 2.458,2.208 2.594,2.208 true 1.667,2.188 1.792,2.188 1.792,2.188 2.063,1.5 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.781,0.271 2.24,0.469 0.458,0.198 10 false G129 5.167,0.292 5.625,0.49 0.458,0.198 10 false C74 0.729,0.646 1.344,0.844 0.615,0.198 10 false BATT 6.281,0.583 6.896,0.781 0.615,0.198 10 false E1 2.667,2.125 3.281,2.323 0.615,0.198 10 false CANH 1.26,2.115 1.875,2.313 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G129-24 (CANH) - G129-23 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G129-24 (CANH) - C74-7 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G129-23 (CANL) - C74-7 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G129-24 (CANH) - G129-2 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G129-23 (CANL) - G129-2 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 1GR-FE)


A225776E25
0.625,0.427 1.052,0.646 0.427,0.219 1.625,0.448 2.052,0.667 0.427,0.219 3.125,0.438 3.552,0.656 0.427,0.219 4.115,0.448 4.542,0.667 0.427,0.219 5.115,0.448 5.542,0.667 0.427,0.219 6.219,0.427 6.646,0.646 0.427,0.219 1.76,2.469 1.99,2.469 1.99,2.469 2.177,2.052 true 2.198,1.875 2.615,2.51 2.615,2.51 2.865,2.51 true 0.354,2.063 0.583,2.5 0.583,2.5 0.75,2.5 true 5.75,1.76 6.167,2.396 6.167,2.396 6.417,2.396 true 0.667,0.448 1.042,0.677 0.375,0.229 10 false G158 1.667,0.458 2.042,0.688 0.375,0.229 10 false G159 3.188,0.458 3.563,0.688 0.375,0.229 10 false C120 1.344,2.344 1.865,2.615 0.521,0.271 10 false CANH 2.906,2.365 3.427,2.635 0.521,0.271 10 false CANL 0.792,2.396 1.313,2.667 0.521,0.271 10 false BATT 6.469,2.271 6.99,2.542 0.521,0.271 10 false E01 4.177,0.448 4.552,0.677 0.375,0.229 10 false C119 5.167,0.458 5.542,0.688 0.375,0.229 10 false C118 6.26,0.438 6.635,0.667 0.375,0.229 10 false C117

a.

Disconnect the ECM connectors.

C329345C05
0.344,0.385 0.802,0.667 0.458,0.281 4.99,0.354 5.448,0.635 0.458,0.281 2.698,0.396 3.156,0.677 0.458,0.281 0.51,1.5 0.646,1.5 0.646,1.5 1.052,1.188 true 5.271,0.969 5.406,0.969 5.406,0.969 5.615,1.188 true 4.125,1.26 4.365,1.177 4.365,1.177 4.469,1.177 true 5.302,1.542 5.438,1.542 5.438,1.542 5.625,1.333 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 0.188,1.427 0.521,1.625 0.333,0.198 10 false E01 0.417,0.427 0.875,0.625 0.458,0.198 10 false C118 4.875,0.854 5.333,1.052 0.458,0.198 10 false CANL 5.042,0.396 5.5,0.594 0.458,0.198 10 false G159 2.75,0.438 3.208,0.635 0.458,0.198 10 false G158 4.51,1.073 4.969,1.271 0.458,0.198 10 false BATT 4.896,1.438 5.354,1.635 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G159-31 (CANH) - G159-25 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G159-31 (CANH) - C118-23 (E01) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G159-25 (CANL) - C118-23 (E01) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G159-31 (CANH) - G158-24 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G159-25 (CANL) - G158-24 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130E30
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.906,1.208 2.677,1.646 2.677,1.646 2.552,1.646 true 3.042,1.208 3.229,1.615 3.229,1.615 3.417,1.615 true 4,1.135 4.844,0.417 4.844,0.417 4.927,0.417 true 3.479,0.323 3.76,0.49 0.281,0.167 10 false G8 5,1.479 5.26,1.667 0.26,0.188 10 false B 2.135,1.563 2.552,1.729 0.417,0.167 10 false CANH 3.448,1.531 3.875,1.688 0.427,0.156 10 false CANL 5.01,0.344 5.313,0.521 0.302,0.177 10 false EP

a.
C240157C36
1.531,0.146 1.969,0.458 0.438,0.313 1.396,1.25 2.104,1.781 2.104,1.781 2.333,1.781 true 1.302,1.24 1.042,1.865 1.042,1.865 0.802,1.865 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 2.635,0.552 2.479,0.552 2.479,0.552 2.052,1.198 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false G8 0.385,1.802 0.802,2 0.417,0.198 10 false CANH 2.375,1.708 2.854,1.906 0.479,0.198 10 false CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 false B 2.698,0.469 3.063,0.729 0.365,0.26 10 false EP
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G8-36 (CANH) - G8-35 (CANL) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G8-36 (CANH) - G8-27 (EP) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-35 (CANL) - G8-27 (EP) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-36 (CANH) - G8-21 (B) SB - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-35 (CANL) - G8-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


for Type A:
C231510N04
3.021,0.073 3.375,0.302 0.354,0.229 4.167,0.083 4.521,0.313 0.354,0.229 3.073,0.104 3.531,0.302 0.458,0.198 10 false G46 4.229,0.115 4.688,0.313 0.458,0.198 10 false N15

for Type B:
C123353E87
2.594,0.688 2.979,0.917 0.385,0.229 3.854,0.688 4.24,0.917 0.385,0.229 4.719,0.677 5.104,0.906 0.385,0.229 3.417,2.583 3.25,2.583 3.25,2.583 3.156,1.75 true 3.833,2.417 3.667,2.417 3.667,2.417 3.344,2.01 true 2.5,2.417 2.667,2.417 2.667,2.417 2.823,2 true 2.646,0.698 3.031,0.927 0.385,0.229 10 false G46 3.927,0.698 4.271,0.938 0.344,0.24 10 false N14 4.792,0.698 5.198,0.958 0.406,0.26 10 false N15 3.469,2.479 3.969,2.708 0.5,0.229 10 false CANH 3.896,2.323 4.396,2.552 0.5,0.229 10 false CANL 2.271,2.313 2.583,2.531 0.313,0.219 10 false E1

a.
C227529C06
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.479,2.573 0.823,2.781 0.344,0.208 10 false G7 0.417,1 0.76,1.208 0.344,0.208 10 false G46 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G46-13 (CANH) - G46-22 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G46-13 (CANH) - G46-25 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-22 (CANL) - G46-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-13 (CANH) - G7-16 (BAT) Y - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G46-22 (CANL) - G7-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC)


C306841E03
3.302,0.156 3.719,0.406 0.417,0.25 1.49,0.365 1.708,0.365 1.708,0.365 2.885,1.073 true 1.521,2.292 1.719,2.292 1.719,2.292 2.885,1.385 true 0.896,0.708 1.115,0.708 1.115,0.708 2.104,1.104 true 5.625,2.208 5.448,2.208 5.448,2.208 4.979,1.677 true 3.406,0.219 3.865,0.417 0.458,0.198 10 false A4 1.115,2.25 1.625,2.396 0.51,0.146 10 false CANH 1.083,0.323 1.594,0.469 0.51,0.146 10 false CANL 0.625,0.646 0.906,0.854 0.281,0.208 10 false BM 5.708,2.125 6.219,2.271 0.51,0.146 10 false GND1

a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C306842C08
3.448,0.292 3.781,0.573 0.333,0.281 3.938,1.115 4.708,0.656 4.708,0.656 4.885,0.656 true 4.375,1.188 4.906,1.875 4.906,1.875 5.083,1.875 true 3.958,1.281 4.729,2.333 4.729,2.333 4.906,2.333 true 2.771,1.417 2.406,2.063 2.406,2.063 2.208,2.063 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 3.531,0.354 3.99,0.552 0.458,0.198 10 false A4 4.938,0.583 5.552,0.781 0.615,0.198 10 false CANL 4.99,2.25 5.604,2.448 0.615,0.198 10 false CANH 5.125,1.802 5.74,2 0.615,0.198 10 false BM 1.792,1.979 2.406,2.177 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A4-22 (CANH) - A4-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-10 (CANL) - A4-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-22 (CANH) - A4-13 (BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A4-10 (CANL) - A4-13 (BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC)


C197053E24
1.458,0.083 1.875,0.344 0.417,0.26 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 2.375,1.417 2.635,1.844 2.635,1.844 2.802,1.844 true 2.344,1.604 1.969,2.042 1.969,2.042 2.229,2.042 true 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 0.719,1.479 0.375,1.979 0.375,1.979 0.573,1.979 true 2.271,1.958 2.74,2.135 0.469,0.177 10 false CANH 2.844,1.771 3.313,1.948 0.469,0.177 10 false CANL 2.948,0.26 3.365,0.427 0.417,0.167 10 false GND1 0.625,1.906 1.177,2.083 0.552,0.177 10 false +BM 1.583,0.146 1.896,0.313 0.313,0.167 10 false A3

a.
C317089C01
1.563,0.156 2.031,0.406 0.469,0.25 0.521,0.594 0.667,0.594 0.667,0.594 1.156,1.031 true 0.5,1.031 0.635,1.031 0.635,1.031 1.448,1.26 true 0.625,1.927 0.771,1.927 0.771,1.927 1.458,1.365 true 2.135,1.979 2.281,1.979 2.281,1.979 2.469,1.354 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.198,1.844 0.625,2.042 0.427,0.198 10 false CANH 0.115,0.958 0.5,1.167 0.385,0.208 10 false CANL 1.792,1.906 2.135,2.125 0.344,0.219 10 false +BM 0.135,0.531 0.573,0.74 0.438,0.208 10 false GND1 1.729,0.198 2.042,0.396 0.313,0.198 10 false A3
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A3-25 (CANH) - A3-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A3-25 (CANH) - A3-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-14 (CANL) - A3-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-25 (CANH) - A3-24 (+BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A3-14 (CANL) - A3-24 (+BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC)


C228050E05
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 false G22 2.833,0.896 3.24,1.052 0.406,0.156 10 false ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 false CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 false CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 false BAT

a.
C277459C10
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G22 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G22-3 (CANH) - G22-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G22-3 (CANH) - G22-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G22-2 (CANL) - G22-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G22-3 (CANH) - G22-5 (BAT) BE - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G22-2 (CANL) - G22-5 (BAT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


B391999E04
2.281,0.583 2.781,0.833 0.5,0.25 4.052,0.583 4.552,0.833 0.5,0.25 1.646,2.094 1.781,2.094 1.781,2.094 2.052,1.365 true 2.677,2.094 2.813,2.094 2.813,2.094 3.042,1.365 true 3.563,0.688 3.698,0.688 3.698,0.688 3.667,1.323 true 4.229,2.104 4.104,2.104 4.104,2.104 3.698,1.427 true 2.396,0.635 2.854,0.833 0.458,0.198 10 false G16 4.167,0.635 4.625,0.833 0.458,0.198 10 false G17 4.292,2.021 4.906,2.219 0.615,0.198 10 false CANH 3.125,0.625 3.74,0.823 0.615,0.198 10 false CANL 2.427,2.021 3.042,2.219 0.615,0.198 10 false +B 1.458,2.031 2.073,2.229 0.615,0.198 10 false E

a.

Disconnect the certification ECU (smart key ECU assembly) connectors.

E277246C06
1.875,0.667 2.292,0.917 0.417,0.25 4.74,0.667 5.156,0.917 0.417,0.25 1.229,1.365 0.865,2.167 0.865,2.167 0.719,2.167 true 2.896,1.333 3.135,2.208 3.135,2.208 3.271,2.208 true 6.333,0.854 6.198,0.854 6.198,0.854 6.063,1.313 true 6.031,1.49 6.177,2.188 6.177,2.188 6.333,2.188 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 0.469,2.104 0.729,2.302 0.26,0.198 10 false +B 3.354,2.135 3.667,2.333 0.313,0.198 10 false E 6.417,0.781 6.813,0.979 0.396,0.198 10 false CANL 6.396,2.115 6.885,2.313 0.49,0.198 10 false CANH 1.969,0.708 2.427,0.906 0.458,0.198 10 false G16 4.844,0.708 5.302,0.906 0.458,0.198 10 false G17
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G17-40 (CANH) - G17-18 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G17-40 (CANH) - G16-10 (E) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G17-18 (CANL) - G16-10 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G17-40 (CANH) - G16-1 (+B) G - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G17-18 (CANL) - G16-1 (+B) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


C297912E06
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 5,0.802 5.302,1.333 5.302,1.333 5.469,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.521,0.177 2.135,0.375 0.615,0.198 10 false G43 4.979,0.156 5.594,0.354 0.615,0.198 10 false G41 5.521,1.229 6.135,1.427 0.615,0.198 10 false CANH 4.042,1.271 4.656,1.469 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C14
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.594,0.281 2.052,0.479 0.458,0.198 10 false G43 1.563,1.865 2.021,2.063 0.458,0.198 10 false G41 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G41-9 (CANH) - G41-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G41-9 (CANH) - G43-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G41-10 (CANL) - G43-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G41-9 (CANH) - G43-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G41-10 (CANL) - G43-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


E317641E04
3.99,0.458 4.448,0.75 0.458,0.292 2.271,2.01 2.854,2.292 0.583,0.281 3.583,1.667 3.75,1.667 3.75,1.667 3.927,1.115 true 4.333,1.667 4.167,1.667 4.167,1.667 4.042,1.115 true 2.917,3.25 2.75,3.25 2.75,3.25 2.552,2.771 true 2.115,2.583 1.917,2.25 1.917,2.25 1.75,2.25 true 4.042,0.51 4.427,0.698 0.385,0.188 10 false G100 2.385,2.052 2.927,2.323 0.542,0.271 10 false G102 3.177,1.573 3.813,1.917 0.635,0.344 10 false CANL 4.385,1.563 5.021,1.906 0.635,0.344 10 false CANH 1.438,2.146 2.073,2.49 0.635,0.344 10 false +B1 2.979,3.156 3.615,3.5 0.635,0.344 10 false GND1

a.
C277477C19
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.552,0.281 2.01,0.479 0.458,0.198 10 false G102 1.521,1.865 1.979,2.063 0.458,0.198 10 false G100 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G100-9 (CANH) - G100-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G100-9 (CANH) - G102-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G100-10 (CANL) - G102-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G100-9 (CANH) - G102-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G100-10 (CANL) - G102-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)


C323669E02
2.552,0.469 3,0.698 0.448,0.229 4.24,0.448 4.677,0.698 0.438,0.25 4.521,2.406 4.365,2.406 4.365,2.406 4.021,1.594 true 3.219,2.417 3.385,2.417 3.385,2.417 3.708,1.49 true 1.24,2.427 1.385,2.427 1.385,2.427 1.771,1.5 true 1.219,0.479 1.385,0.479 1.385,0.479 1.781,1.292 true 2.635,0.5 3.094,0.698 0.458,0.198 10 false C60 4.333,0.49 4.604,0.656 0.271,0.167 10 true C61 0.771,0.396 1.229,0.656 0.458,0.26 10 false CANH 0.823,2.365 1.25,2.646 0.427,0.281 10 false CANL 2.958,2.344 3.573,2.542 0.615,0.198 10 false +B 4.604,2.323 5.219,2.521 0.615,0.198 10 false GND

a.
C325480C03
1.521,0.365 1.927,0.615 0.406,0.25 1.427,2.292 1.792,2.542 0.365,0.25 0.521,1.458 0.969,1.927 0.969,1.927 1.135,1.927 true 2.302,3.573 2.708,4.25 2.708,4.25 2.854,4.25 true 2.719,0.573 2.844,0.573 2.844,0.573 2.906,1.229 true 2.688,1.958 2.813,1.958 2.813,1.958 2.906,1.448 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.406 2.063,0.604 0.458,0.198 10 false C60 1.49,2.333 1.948,2.531 0.458,0.198 10 false C61 1.188,1.896 1.5,2.094 0.313,0.198 10 false +B 2.906,4.177 3.219,4.375 0.313,0.198 10 false GND 2.271,1.885 2.729,2.083 0.458,0.198 10 false CANL 2.271,0.5 2.729,0.698 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C60-20 (CANH) - C60-40 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C60-20 (CANH) - C61-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C60-40 (CANL) - C61-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C60-20 (CANH) - C60-21 (+B) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C60-40 (CANL) - C60-21 (+B) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


C278749E02
3.375,0.25 3.854,0.542 0.479,0.292 2.417,0.25 2.75,0.25 2.75,0.25 3.375,1.417 true 2.167,0.5 2.5,0.5 2.5,0.5 3.25,1.406 true 4.365,1.521 5.063,2.417 5.063,2.417 5.417,2.417 true 2.083,2.417 2.417,2.417 2.417,2.417 3.083,1.406 true 3.479,0.333 3.938,0.531 0.458,0.198 10 false G37 1.917,0.427 2.167,0.615 0.25,0.188 10 false TX- 1.75,2.333 2.208,2.531 0.458,0.198 10 false GND 2.125,0.177 2.417,0.375 0.292,0.198 10 false TX+ 5.479,2.333 5.938,2.531 0.458,0.198 10 false B

a.
C240157C37
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.344,1.063 0.802,1.26 0.458,0.198 10 false G37 2.333,0.406 2.792,0.604 0.458,0.198 10 false TX+ 2.24,0.156 2.698,0.354 0.458,0.198 10 false TX- 3.031,1.531 3.333,1.802 0.302,0.271 10 false B 0.667,0.385 1.031,0.646 0.365,0.26 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-11 (TX+) - G37-12 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G37-11 (TX+) - G37-14 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-12 (TX-) - G37-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-11 (TX+) - G37-21 (B) GR - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G37-12 (TX-) - G37-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)


E219842E05
3.365,0.208 3.813,0.469 0.448,0.26 1.969,0.438 2.198,0.438 2.198,0.438 2.615,0.865 true 2.333,0.229 2.563,0.229 2.563,0.229 2.76,0.844 true 2.229,1.354 2.396,1.354 2.396,1.354 2.698,1.031 true 3.417,0.24 3.875,0.438 0.458,0.198 10 false G107 2.031,0.156 2.51,0.354 0.479,0.198 10 false TX+ 1.708,0.375 2.188,0.573 0.479,0.198 10 false TX- 1.896,1.271 2.375,1.469 0.479,0.198 10 false GND

a.
C300856C09
1.542,2.781 1.958,3.052 0.417,0.271 1.396,0.208 1.813,0.479 0.417,0.271 1.865,1.927 1.979,1.927 1.979,1.927 2.521,1.063 true 2.667,1.063 2.823,0.354 2.823,0.354 2.958,0.354 true 1.781,4.427 1.906,4.427 1.906,4.427 2.344,3.958 true 1.979,2.292 2.094,2.292 2.094,2.292 2.635,1.229 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.198,2.635 0.51,2.792 0.313,0.156 10 false *b 1.656,2.844 1.938,3.01 0.281,0.167 10 false G7 1.448,0.26 1.813,0.417 0.365,0.156 10 false G107 1.583,1.844 2.01,2 0.427,0.156 10 false TX+ 3,0.302 3.427,0.458 0.427,0.156 10 false TX- 1.469,4.365 1.896,4.521 0.427,0.156 10 false BAT 1.635,2.219 2.063,2.375 0.427,0.156 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G107-8 (TX+) - G107-9 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G107-8 (TX+) - G107-23 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G107-9 (TX-) - G107-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G107-8 (TX+) - G7-16 (BAT) GR - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G107-9 (TX-) - G7-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)


E101528E38
3.448,0.146 3.792,0.365 0.344,0.219 1.49,1.458 1.656,1.458 1.656,1.458 2.333,0.865 true 1.719,0.354 1.885,0.354 1.885,0.354 2.677,0.76 true 1.885,0.146 2.052,0.146 2.052,0.146 2.865,0.76 true 3.49,0.177 3.844,0.406 0.354,0.229 10 false G40 1.438,0.083 2.052,0.281 0.615,0.198 10 false CANH 1.313,0.292 1.927,0.49 0.615,0.198 10 false CANL 1.25,1.385 1.865,1.583 0.615,0.198 10 false E1

a.
C281183C06
1.573,0.229 1.938,0.49 0.365,0.26 0.292,2.51 0.656,2.771 0.365,0.26 2.552,3.094 2.406,3.094 2.406,3.094 2.219,2.823 true 2.75,0.448 2.604,0.448 2.604,0.448 2.375,0.99 true 2.552,0.208 2.406,0.208 2.406,0.208 2.25,1.01 true 2,1.885 2.188,1.885 2.188,1.885 2.625,1.052 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.104,1.979 0.417,2.135 0.313,0.156 10 false *b 0.385,2.542 0.698,2.698 0.313,0.156 10 false G7 2.625,3.01 3.083,3.26 0.458,0.25 10 false BAT 1.615,0.271 1.927,0.427 0.313,0.156 10 false G40 2.615,0.094 3.104,0.292 0.49,0.198 10 false CANH 2.802,0.354 3.292,0.552 0.49,0.198 10 false CANL 1.75,1.813 1.979,2.01 0.229,0.198 10 false E1
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G40-6 (CANH) - G40-7 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G40-6 (CANH) - G40-9 (E1) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G40-7 (CANL) - G40-9 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G40-6 (CANH) - G7-16 (BAT) V - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G40-7 (CANL) - G7-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX NETWORK DOOR ECU (w/ Back Door Closer System)


C278778C04
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 2.427,0.167 2.844,0.417 0.417,0.25 4.313,0.167 4.729,0.417 0.417,0.25 5.635,2.094 5.448,2.094 5.448,2.094 5.094,1.615 true 5.479,2.354 5.292,2.354 5.292,2.354 5.042,1.594 true 3.219,2.094 3,2.094 3,2.094 2.646,1.51 true 2.125,2.094 2.344,2.094 2.344,2.094 2.542,1.5 true 2.5,0.583 2.958,0.781 0.458,0.198 10 false V26 4.385,0.552 4.844,0.75 0.458,0.198 10 false V25 5.688,2.031 6.146,2.229 0.458,0.198 10 false CANP 5.531,2.281 5.99,2.479 0.458,0.198 10 false CANN 3.271,2.021 3.729,2.219 0.458,0.198 10 false GND 1.958,2.021 2.417,2.219 0.458,0.198 10 false B 2.938,0.573 3.396,0.771 0.458,0.198 10 false *B 2.51,0.198 2.969,0.396 0.458,0.198 10 false V13 2.938,0.188 3.396,0.385 0.458,0.198 10 false *A 4.396,0.188 4.854,0.385 0.458,0.198 10 false V12 4.823,0.198 5.281,0.396 0.458,0.198 10 false *A 4.781,0.531 5.24,0.729 0.458,0.198 10 false *B
*A w/ Power Back Door System *B w/o Power Back Door System


a.
C300898C06
0.844,2.573 1.292,2.823 0.448,0.25 1.844,2.563 2.292,2.813 0.448,0.25 0.948,0.406 1.396,0.656 0.448,0.25 1.844,0.396 2.292,0.646 0.448,0.25 0.563,4.167 0.667,4.167 0.667,4.167 0.927,3.667 true 1.031,2.031 1.146,2.031 1.146,2.031 1.542,1.573 true 2.292,2.031 2.156,2.031 2.156,2.031 1.813,1.573 true 1.479,4.177 1.365,4.177 1.365,4.177 1.052,3.667 true 0.156,0.156 0.469,0.313 0.313,0.156 10 false *a 1.948,2.604 2.26,2.76 0.313,0.156 10 false V25 1.052,0.438 1.365,0.594 0.313,0.156 10 false V13 0.156,4.063 0.677,4.281 0.521,0.219 10 false CANP 1.531,4.063 2.542,4.396 1.01,0.333 10 false CANN 2.375,1.906 2.771,2.104 0.396,0.198 10 false B 0.708,1.917 1.104,2.115 0.396,0.198 10 false GND 0.938,2.615 1.25,2.771 0.313,0.156 10 false V12 1.365,2.604 1.677,2.76 0.313,0.156 10 false *A 2.396,2.604 2.708,2.76 0.313,0.156 10 false *B 1.469,0.427 1.781,0.583 0.313,0.156 10 false *A 1.927,0.417 2.24,0.573 0.313,0.156 10 false V26 2.365,0.427 2.677,0.583 0.313,0.156 10 false *B
*A w/ Power Back Door System
*B w/o Power Back Door System
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

w/ Power Back Door System
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V12-13 (CANP) - V12-14 (CANN) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V12-13 (CANP) - V13-7 (GND) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
V12-14 (CANN) - V13-7 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
V12-13 (CANP) - V13-8 (B) SB - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V12-14 (CANN) - V13-8 (B) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/o Power Back Door System
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V25-13 (CANP) - V25-14 (CANN) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V25-13 (CANP) - V26-7 (GND) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
V25-14 (CANN) - V26-7 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
V25-13 (CANP) - V26-8 (B) SB - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V25-14 (CANN) - V26-8 (B) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher