Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.07
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0218827 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E323305E06
5.563,1.396 6.833,1.76 1.271,0.365 10 false G8 5.573,1.552 6.844,1.917 1.271,0.365 10 false Combination Meter Assembly 5.646,0.885 6.917,1.25 1.271,0.365 10 false +S 1.271,0.885 2.542,1.25 1.271,0.365 10 false SPD 1.281,2.729 2.552,3.094 1.271,0.365 10 false SPD 1.25,4.531 2.521,4.896 1.271,0.365 10 false SPD 5.646,4.542 6.917,4.906 1.271,0.365 10 false SPD1 5.646,2.719 6.917,3.083 1.271,0.365 10 false SPD 5.448,2.708 6.719,3.073 1.271,0.365 10 false 5 5.385,0.875 6.656,1.24 1.271,0.365 10 false 19 1.708,0.979 2.01,1.271 0.302,0.292 10 false G49 2.125,0.979 2.458,1.313 0.333,0.333 10 false G56 2.51,0.99 2.917,1.385 0.406,0.396 10 false G159 2.958,1 4.229,1.365 1.271,0.365 10 false G129 1.688,0.781 2.052,0.979 0.365,0.198 10 false 10*1 2.135,0.771 3.406,1.135 1.271,0.365 10 false 23*2 2.552,0.771 3.823,1.135 1.271,0.365 10 false 12*3 2.969,0.771 4.24,1.135 1.271,0.365 10 false 17*4 0.438,3.25 2.302,3.625 1.865,0.375 10 false G16 0.438,3.406 2.302,3.781 1.865,0.375 10 false Certification ECU (Smart Key ECU Assembly)*5 1.688,2.74 3.552,3.115 1.865,0.375 10 false 7 5.729,3.24 6.74,3.615 1.01,0.375 10 false G33 5.729,3.385 6.74,3.76 1.01,0.375 10 false Body ECU 0.333,5.083 2.073,5.479 1.74,0.396 10 false G108 0.333,5.26 3.26,5.5 2.927,0.24 10 false Radio Receiver Assembly 5.958,5.094 6.323,5.49 0.365,0.396 10 false G132 5.969,5.26 6.771,5.719 0.802,0.458 10 false TCM*6 5.365,4.552 5.729,4.948 0.365,0.396 10 false 25 1.688,4.552 2.052,4.948 0.365,0.396 10 false 17 0.281,5.865 2.188,6.021 1.906,0.156 10 false *1: for 1GD-FTV 0.281,6.177 2.188,6.333 1.906,0.156 10 false *2: for 2TR-FE, 2TR-FBE 0.292,6.479 2.198,6.635 1.906,0.156 10 false *3: for 1GR-FE 2.083,5.865 3.99,6.021 1.906,0.156 10 false *4: for 1KD-FTV 2.083,6.167 4.542,6.365 2.458,0.198 10 false *5: w/ Smart Entry and Start System 2.083,6.479 5.417,6.667 3.333,0.188 10 false *6: for 1KD-FTV with Automatic Transmission 0.865,1.427 2.135,1.792 1.271,0.365 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C28
1.479,0.438 1.896,0.656 0.417,0.219 0.656,1.802 0.865,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.458 1.906,0.656 0.313,0.198 10 false G8 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.583 3.188,3.854 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G8-19 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G8-19 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 1GD-FTV

*2: for 2TR-FE, 2TR-FBE

*3: for 1GR-FE

*4: for 1KD-FTV


a.

Disconnect the G108 radio receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

w/ Smart Entry and Start System:

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G33 body ECU connector.


e.

Disconnect the G49*1, G56*2, G159*3 or G129*4 ECM connector.


f.

for 1KD-FTV with Automatic Transmission:

Disconnect the G132 TCM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-17 (SPD) - G8-19 (+S) Always Below 1 Ω
G108-17 (SPD) or G8-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR