Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE › from 2016.07
RM33K0E _51 Engine / Hybrid System _054513 2TR-FBE ENGINE MECHANICAL _0272871 ENGINE G

2TR-FBE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case.


b.

Check that the air cleaner filter element sub-assembly is not excessively dirty.

If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.

If cleaning the air cleaner filter element sub-assembly, blow compressed air to clean it.

NOTICE:
·

Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.

·

When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.



HINT:

When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.



c.

Reinstall the air cleaner filter element sub-assembly to the air cleaner case.


Hide 16361A 6.INSPECT FAN AND GENERATOR V BELT

Hide 16620D 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16603 8.INSPECT NO. 1 IDLER PULLEY

a.

Idle the engine, and then stop the engine. Check that the fan and generator V belt is between the edges of the idler pulley.


b.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>DRIVE BELT>REMOVAL


c.
A346796C01
2,0.344 2.229,0.552 0.229,0.208 10 true *a
*a Turn


Turn the pulley, and check that the idler bearing moves smoothly and quietly.

If necessary, replace the No. 1 idler pulley.


d.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION


Hide 13750 9.INSPECT VALVE LASH ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspection.

HINT:

If any defects or problems are found during the preceding inspection, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION



Hide 10.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

NOTICE:

Switch off all the accessories and the A/C before connecting the GTS.



ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

2 to 15° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.



v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.




c.

When not using the GTS:

i.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



ii.

Start the engine and idle it.


iii.
A206183C53
1.219,0.313 1.354,0.313 1.354,0.313 1.573,0.906 true 2.125,1.865 1.99,1.865 1.99,1.865 1.781,1.479 true 0.083,0.063 0.646,0.396 0.563,0.333 10 false *a 0.917,0.229 1.333,0.5 0.417,0.271 10 false CG 2.156,1.771 2.677,2.063 0.521,0.292 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

When checking the ignition timing, the transmission should be in N or P.



iv.

Using the timing light, measure the ignition timing.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the ignition timing, the transmission should be in N or P.




v.

Remove SST from the DLC3.


vi.

Check the ignition timing.

Standard ignition timing:

2 to 15° BTDC @ idle



vii.

Confirm that the ignition timing advances immediately when the engine speed is increased.


viii.

Turn the ignition switch off.


ix.

Disconnect the timing light from the wire of the ignition coil connector for the No. 1 cylinder.



Hide 11.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

NOTICE:

Switch off all accessories and the A/C before connecting the GTS.



ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9
Standard idle speed:

600 to 700 rpm


NOTICE:

When checking the idle speed, the transmission should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.



v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A206183C54
0.74,1.885 0.865,1.885 0.865,1.885 1.042,1.469 true 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.427,1.781 0.75,1.958 0.323,0.177 10 false TAC
*a Front view of DLC3


Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Switch off all accessories and the A/C before connecting the terminals.



ii.

Start the engine and idle it.


iii.

Check the idle speed.

Standard idle speed:

600 to 700 rpm




Hide 12.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Check for DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

c.

Disconnect the 4 fuel injector connectors.



e.

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1230 kPa (12.5 kgf/cm2, 178 psi) or higher


Minimum pressure:

880 kPa (9.0 kgf/cm2, 128 psi)


Difference between each cylinder:

68 kPa (0.7 kgf/cm2, 9.9 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.






g.

Connect the 4 fuel injector connectors.


h.

Check for DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Hide 13.CHECK CO/HC

a.

Start and warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds, and then idle the engine.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tail exhaust pipe assembly.


d.

Check the CO/HC concentration at idle.

Standard idle CO concentration:

0 to 0.5%


Standard idle HC concentration:

Refer to applicable local regulation



e.

If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

i.

Check the air fuel ratio sensor operation.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION


ii.

Check the heated oxygen sensor operation.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION


iii.

See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

CO HC Problems Causes
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake and exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body with motor assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve sub-assembly

3.

Faulty SFI system:

·

Faulty fuel pressure regulator assembly

·

Defective engine coolant temperature sensor

·

Defective intake mass air flow meter sub-assembly

·

Faulty ECM

·

Faulty fuel injector assemblies

·

Faulty throttle body with motor assembly