Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
72201B
1.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH
Attach the claw and install the seat track handle sub-assembly LH.
71052A
2.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
While rotating the part in installation direction (1) shown in the illustration, attach the hook.
Push in Installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly LH.
71538B
3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to install the guide.
While expanding the part in installation direction (2) shown in the illustration, attach the claw.
Install the front seat cushion edge protector LH with the screw.
71537G
4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Use the same procedure as for the LH side.
71874
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to attach the guide.
Push in the installation direction (2) shown in the illustration to attach the clip.
|
Install in this Direction |
Push in the guide in the installation direction shown in the illustration.
Install the front seat lower cushion shield LH with the screw.
71873
6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Use the same procedure as for the LH side.
7.INSTALL SEAT COVER WIRE
Install the seat cover wire.
There are service parts available for wires of 1000 mm or longer and formed wires.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.
Refer to the precautions when creating a wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 170 mm (6.70 in.) |
| B | 150 mm (5.91 in.) |
| C | 230 mm (9.06 in.) |
| D | 270 mm (10.63 in.) |
| E | 290 mm (11.42 in.) |
The dimensions shown in the illustration are the length.
71071S
8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
As shown in the illustration, fix all of the cover seam allowances in the same direction.
Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.
Do not dirty or damage the separate type front seat cushion cover.
Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.
| *1 | Hog Ring Pliers | - | - |
9.INSTALL SEAT CUSHION COVER WITH PAD
While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to attach the seat cushion cover with pad.
71587B
10.INSTALL FRONT SEATBACK EDGE PROTECTOR
Attach the claw to Install the 2 front seatback edge protectors.
71054S
11.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly LH.
Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly LH.
Push in installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly LH.
Attach the claw and install the 2 front seatback edge protectors.
71759D
12.INSTALL FRONT NO. 2 SEATBACK HOOK
|
Install in this Direction |
Push up installation direction shown in the illustration to attach the claw and install the 2 front No. 2 seatback hooks.
73920A
13.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)
14.INSTALL SEAT COVER WIRE
Install the seat cover wire.
There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.
Refer to the precautions when creating a wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 200 mm (7.87 in.) |
| B | 420 mm (1.38 ft.) |
The dimensions shown in the illustration are the length.
71073S
15.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
As shown in the illustration, fix all of the cover seam allowances in the same direction.
Set the separate type front seatback cover.
Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.
Do not dirty or damage the separate type front seatback cover.
Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
16.INSTALL SEATBACK COVER WITH PAD
|
Install in this Direction |
Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.
w/ Front Seat Side Airbag:
| *1 | J Hook A |
| *2 | J Hook B |
|
Install in this Direction |
Push in installation direction shown in the illustration to attach the J hook A and J hook B.
| *1 | J Hook B (J Hook A and J Hook B) |
| *2 | J Hook C |
|
Install in this Direction |
Push in installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.
Install the new rivet to J hook B.
| *A | for LH seat | *B | for RH seat |
| *1 | J Hook A | *2 | J Hook B |
Place your hand at the position shown in the illustration and push in the install direction to attach the J hook B.
| *1 | J Hook A | *2 | J Hook B |
| *3 | J Hook C | - | - |
|
Place Hand Here |
|
Install in this Direction |
71931
17.INSTALL FRONT SEAT HEADREST SUPPORT
|
Install in this Direction |
Attach the claw and install the 2 front seat headrest supports.
|
Install in this Direction |
Pull up installation direction shown in the illustration to attach the guide to the 2 straps.
|
Install in this Direction |
Close the fasteners as shown in the illustration.
Using hog ring pliers, install 6 new hog rings.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
Install the hog rings at the cutouts if they are there.
71759C
18.INSTALL FRONT NO. 1 SEATBACK HOOK
Attach the claw and install the front No. 1 seatback hook.
71876G
19.INSTALL RECLINING ADJUSTER INSIDE COVER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push down installation direction (1) shown in the illustration.
Rotate the part in installation direction (2) shown in the illustration and align the guide to install the reclining adjuster inside cover LH.
71875F
20.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
71014S
21.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH
| *A | RH Side |
| *B | LH Side |
Install the 4 bolts and front seatback frame sub-assembly LH.
| *A | RH Side |
| *B | LH Side |
| *1 | Separate Type Front Seat Cushion Cover |
Attach the hook.
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
w/ Front Seat Side Airbag:
Attach the wire harness clamp and connector clamp.
Install the band in the position shown in the illustration.
73240
22.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
71862
23.INSTALL FRONT SEAT INNER CUSHION SHIELD LH
|
Install in this Direction |
Push in the installation direction shown in the illustration to attach the claw and guide.
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield LH.
71812D
24.INSTALL FRONT SEAT CUSHION SHIELD LH
|
Install in this Direction |
Push in the installation direction shown in the illustration to attach the claw and guide.
|
Install in this Direction |
Push in the installation direction shown in the illustration to attach the claw and guide.
| *1 | Clip A |
| *2 | Clip B |
Attach clip B.
Attach the claw.
Attach clip A and install the front seat cushion shield LH.
72495
25.INSTALL VERTICAL ADJUSTING HANDLE LH
|
Install in this Direction |
Attach the guide, and then push in installation direction shown in the illustration to install the vertical adjusting handle LH.
Install the screw.
72526E
26.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
|
Install in this Direction |
With the reclining adjuster release handle LH pulled up.
Push in installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.
71849
27.INSTALL SEAT ADJUSTER COVER CAP LH
|
Install in this Direction |
Push in installation direction shown in the illustration to install the 2 seat adjuster cover caps LH.
71910A
28.INSTALL FRONT SEAT HEADREST ASSEMBLY
|
Apply Silicon |
Apply silicon lubricant in this range.
Install the front seat headrest assembly.