Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) › from 2016.07
RM33K0E _52 Drivetrain _043591 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0276855 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) J

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C311455E73
0.563,1.719 3.469,1.917 2.906,0.198 10 false from IG1 NO. 4 Fuse 3.635,2.229 4.25,2.427 0.615,0.198 10 false SFTU 3.635,2.823 4.25,3.021 0.615,0.198 10 false SFTD 3.885,1.656 4.5,1.854 0.615,0.198 10 false S 5.167,1.646 5.781,1.844 0.615,0.198 10 false S 5.146,2.229 5.76,2.427 0.615,0.198 10 false SFTU 5.146,2.833 5.76,3.031 0.615,0.198 10 false SFTD 2.625,3.427 3.24,3.625 0.615,0.198 10 false I1 2.604,3.635 4.354,4.156 1.75,0.521 10 false Transmission Control Switch (Transmission Floor Shift Assembly) 5.635,3.844 6.25,4.042 0.615,0.198 10 false C16 5.604,4.01 6.104,4.292 0.5,0.281 10 false ECM 2.719,1.646 3.333,1.844 0.615,0.198 10 false IG 2.729,2.229 3.344,2.427 0.615,0.198 10 false E 2.552,1.646 2.865,1.844 0.313,0.198 10 false 4 2.552,2.229 2.865,2.427 0.313,0.198 10 false 2 4.906,2.833 5.219,3.031 0.313,0.198 10 false 27 4.896,2.24 5.208,2.438 0.313,0.198 10 false 17 4.906,1.656 5.219,1.854 0.313,0.198 10 false 30 4.083,1.656 4.396,1.854 0.313,0.198 10 false 5 4.073,2.229 4.385,2.427 0.313,0.198 10 false 3 4.083,2.823 4.396,3.021 0.313,0.198 10 false 1 6.042,2.042 6.5,2.24 0.458,0.198 10 false 12 V 6.042,2.625 6.5,2.823 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 234 134,135

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the transmission control switch connector.


b.
C277025C65
0.927,1.75 1.76,1.385 true 2.042,1.771 2.031,1.385 true 2.885,1.771 2.292,1.396 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.688,1.802 1.146,2 0.458,0.198 10 false SFTU 2,1.802 2.458,2 0.458,0.198 10 false E 2.771,1.813 3.229,2.01 0.458,0.198 10 false SFTD
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
3 (SFTU) - 2 (E) Shift lever not held in "+" (Up-shift) 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever not held in "-" (Down-shift) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C267936C22
0.229,0.979 0.583,1.24 0.354,0.26 0.927,1.896 1.5,1.406 true 0.813,1.854 1.125,2.052 0.313,0.198 10 false E 0.365,1.031 0.677,1.229 0.313,0.198 10 false I1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C325711C10
1.552,0.198 1.896,0.417 0.344,0.219 1.927,2.719 1.458,1.802 true 0.49,2.708 1.458,1.719 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.594,0.24 1.938,0.438 0.344,0.198 10 false C16 1.594,2.771 2.281,2.958 0.688,0.188 10 false 27 (SFTD) 0.156,2.75 0.906,2.948 0.75,0.198 10 false 17 (SFTU)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-17 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
C16-27 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
C16-17 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
C16-27 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C277025C33
0.802,1.802 1.219,1.385 true 1.615,1.781 1.479,1.396 true 1.573,1.833 1.885,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C267936C23
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.354,1.031 0.667,1.229 0.313,0.198 10 false I1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I1-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I1-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the I1 transmission control switch connector.


b.

Disconnect the C16 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-5 (S) - C16-30 (S) Always Below 1 Ω
I1-5 (S) - Body ground Always 10 kΩ or higher
C16-30 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR