Home › Engine / Hybrid System › 1GD-FTV EMISSION CONTROL › EXHAUST GAS TEMPERATURE SENSOR › from 2016.10
RM33K0E _51 Engine / Hybrid System _043574 1GD-FTV EMISSION CONTROL _0225242 EXHAUST GAS TEMPERATURE SENSOR A

1GD-FTV EMISSION CONTROL  EXHAUST GAS TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 89425 1.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 3 exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 3 exhaust gas temperature sensor is dropped, replace the new one.

·

When reusing the No. 3 exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the No. 3 exhaust gas temperature sensor.



HINT:
·

The connector color of the No. 3 exhaust gas temperature sensor is gray.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 2 exhaust gas temperature sensor is dropped, replace the new one.

·

When reusing the No. 2 exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the No. 2 exhaust gas temperature sensor.



HINT:
·

The connector color of the No. 2 exhaust gas temperature sensor is black.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




c.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the exhaust gas temperature sensor is dropped, replace the new one.

·

When reusing the exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the exhaust gas temperature sensor.



HINT:
·

The connector color of the exhaust gas temperature sensor is white.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




d.
A346698C01
1.208,0.625 0.792,0.625 true 1.719,0.615 1.49,0.208 1.49,0.208 1.323,0.208 true 2.521,0.365 2.354,0.365 2.354,0.365 2.104,0.698 true 2.542,0.26 2.771,0.417 0.229,0.156 10 true *a 1.115,0.104 1.323,0.26 0.208,0.156 10 true *b 0.573,0.51 0.802,0.677 0.229,0.167 10 true *c
*a White
*b Black
*c Gray


Attach the 3 colored connectors to the pipe clamp in the positions shown in the illustration.


e.

Close the clamp of the pipe clamp, and install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Arrange the exhaust gas temperature sensor wires so that they do not contact each other.



f.

Connect the No. 3 exhaust gas temperature sensor to the No. 1 vacuum pipe.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


g.

Connect the 3 connectors to the 3 exhaust gas temperature sensor.


Hide 89425 2.INSTALL EXHAUST GAS TEMPERATURE SENSOR (for i-ART)

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 2 exhaust gas temperature sensor is dropped, replace the new one.

·

When reusing the No. 2 exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the No. 2 exhaust gas temperature sensor.



HINT:
·

The connector color of the No. 2 exhaust gas temperature sensor is black.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the exhaust gas temperature sensor is dropped, replace the new one.

·

When reusing the exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the exhaust gas temperature sensor.



HINT:
·

The connector color of the exhaust gas temperature sensor is white.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




c.
A386531C01
2.01,0.646 2.24,0.375 2.24,0.375 2.406,0.375 true 1.135,0.323 1.323,0.323 1.323,0.323 1.552,0.604 true 0.927,0.24 1.135,0.427 0.208,0.188 10 true *b 2.427,0.271 2.635,0.458 0.208,0.188 10 true *a
*a White
*b Black


Attach the 2 colored connectors to the pipe clamp in the positions shown in the illustration.


d.

Close the clamp of the pipe clamp, and install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Arrange the exhaust gas temperature sensor wires so that they do not contact each other.



e.

Connect the 2 connectors to the 2 exhaust gas temperature sensor.


Hide 12601B 3.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY