Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2016.10
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  SYSTEM DESCRIPTION  


ENGINE CONTROL SYSTEM


A390290C01
4.188,0.729 4.5,0.927 0.313,0.198 10 false *1 4.24,1.74 4.542,1.948 0.302,0.208 10 false *27 6.75,0.948 7.063,1.146 0.313,0.198 10 false *2 6.344,0.385 6.656,0.583 0.313,0.198 10 false *3 5.104,3.083 5.417,3.281 0.313,0.198 10 false *6 4.031,3.26 4.344,3.458 0.313,0.198 10 false *5 3.302,2.99 3.615,3.188 0.313,0.198 10 false *4 3.708,3.833 4.021,4.031 0.313,0.198 10 false *7 4.156,3.969 4.469,4.167 0.313,0.198 10 false *8 0.927,6.469 1.24,6.667 0.313,0.198 10 false *16 0.979,6.083 1.292,6.281 0.313,0.198 10 false *15 1.031,5.521 1.344,5.719 0.313,0.198 10 false *10 1.083,5.135 1.396,5.333 0.313,0.198 10 false *9 1.396,0.292 1.708,0.49 0.313,0.198 10 false *26 1.115,6.938 1.427,7.135 0.313,0.198 10 false *17 1.094,7.219 1.406,7.417 0.313,0.198 10 false *18 3.75,4.979 4.063,5.177 0.313,0.198 10 false *11 4.406,4.792 4.719,4.99 0.313,0.198 10 false *12 3.729,5.625 4.042,5.823 0.313,0.198 10 false *13 3.219,6.146 3.531,6.344 0.313,0.198 10 false *19 4.083,6 4.396,6.198 0.313,0.198 10 false *20 4.542,7.01 4.854,7.208 0.313,0.198 10 false *21 4.802,6.198 5.115,6.396 0.313,0.198 10 false *14 5.583,6.75 5.896,6.948 0.313,0.198 10 false *23 4.344,7.25 4.656,7.448 0.313,0.198 10 false *24 3.063,7.635 3.375,7.833 0.313,0.198 10 false *25 4.979,6.875 5.292,7.073 0.313,0.198 10 false *22
*1 ECM *2 Fuel Supply Pump Assembly
*3 Pre-stroke Control Valve *4 Common Rail Assembly
*5 Pressure Discharge Valve *6 Glow Plug Controller
*7 Intercooler *8 Intake Air Temperature Sensor (Turbo)
*9 Mass Air Flow Meter Sub-assembly *10 Intake Air Temperature Sensor (Built Into Mass Air Flow Meter Sub-assembly)
*11 EGR Cooler Sub-assembly *12 Vacuum Switching Valve Assembly (for EGR Bypass Valve)
*13 Injector Assembly *14 Electric EGR Control Valve Assembly
*15 Turbocharger Sub-assembly *16 Turbocharger Nozzle Vane Control Actuator
*17 Exhaust Gas Temperature Sensor *18 No. 2 Exhaust Gas Temperature Sensor
*19 Camshaft Position Sensor *20 Glow Plug
*21 Vacuum Switching Valve (for Swirl Control Valve) *22 Manifold Absolute Pressure Sensor
*23 Diesel Throttle Body Assembly *24 Engine Coolant Temperature Sensor
*25 Crankshaft Position Sensor *26 Accelerator Pedal Position Sensor
*27 Atmospheric Pressure Sensor - -



i-ART SYSTEM


In the i-ART (Intelligent Accuracy Refinement Technology) System, i-ART injectors, which are injectors that have built-in pressure sensors, are used.

By incorporating a pressure sensor into the injector, any changes in the internal pressure of the injectors can be confirmed at a point close to where fuel is injected.

The i-ART injector directly detects its internal fuel pressure and fuel temperature.

The ECM receives the pressure waveform signal from the pressure sensor and detects the fuel injection volume to perform so that the fuel injection volume matches the target.

Due to this system, the fuel injection precision even in the smallest amount has been improved and precise control of multilevel injection has been made possible. In turn, combustion is more stable and the noise made during combustion has reduced.

The i-ART injectors automatically perform learning when they are replaced. Therefore, injector compensation code registration and pilot quantity learning is not necessary. Learning is performed while the engine is running.

A379945C01
3.51,3.198 3.073,2.635 3.073,2.635 2.979,2.635 true 3.51,3.688 3.281,3.688 3.281,3.688 3.094,3.604 true 3.646,2.917 3.948,2.385 3.948,2.385 4.073,2.385 true 3.49,2.49 3.146,2.042 3.146,2.042 3.052,2.042 true 3.854,0.656 4.01,0.51 4.01,0.51 4.115,0.51 true 2.813,2.563 3.125,2.76 0.313,0.198 10 false *4 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.906,3.51 3.219,3.708 0.313,0.198 10 false *3 4.125,2.323 4.438,2.521 0.313,0.198 10 false *1 2.865,1.969 3.177,2.167 0.313,0.198 10 false *2 4.156,0.448 4.469,0.646 0.313,0.198 10 false *5
*1 Nozzle *2 Two-Way Valve
*3 Low Suck Volume Nozzle *4 Nozzle Needle
*5
·

Fuel Pressure Sensor

·

Fuel Temperature Sensor


- -
*a Injector Assembly Cross Section Diagram - -



COMMON RAIL SYSTEM DESCRIPTION


a.

Common rail system:

The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.

This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.

The ECM provides an electric current to the solenoid valve in each injector assembly to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor built into each injector. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.

In addition, this system uses a solenoid valve inside each injector assembly to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.

A379942C01
3.948,0.479 4.26,0.677 0.313,0.198 10 false *1 6.469,0.844 6.781,1.042 0.313,0.198 10 false *2 1.083,1.823 1.396,2.021 0.313,0.198 10 false *3 0.771,3.375 1.083,3.573 0.313,0.198 10 false *4 1.427,3.375 1.74,3.573 0.313,0.198 10 false *5 5.656,3.24 5.969,3.438 0.313,0.198 10 false *6 1.51,4.156 1.823,4.354 0.313,0.198 10 false *7 2.031,6.26 2.344,6.458 0.313,0.198 10 false *8 5.719,6.583 6.031,6.781 0.313,0.198 10 false *9 5.042,7.469 5.354,7.667 0.313,0.198 10 false *10 5.031,8.146 5.344,8.344 0.313,0.198 10 false *11
*1 Common Rail Assembly *2 Pressure Discharge Valve
*3 ECM *4 Crankshaft Position Sensor
*5 Camshaft Position Sensor *6 Injector Assembly
*7 Pre-stroke Control Valve *8 Fuel Supply Pump Assembly
*9 Pressurized Fuel Filter *10 Fuel Filter Element Assembly
*11 Fuel Tank Assembly - -
V100143

High Pressure Fuel
V100144

Return Fuel
V100146

Suction Fuel
V100155

Feed Pressure Fuel


HINT:

If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing an injector assembly, etc., the engine startability may deteriorate.



b.

Common rail system components:

Component Description
Common rail assembly Stores high-pressure fuel produced by supply pump
Fuel supply pump assembly
·

Operated by crankshaft via timing chain

·

Supplies high-pressure fuel to common rail


Injector assembly Injects fuel to combustion chamber based on signals from ECM
Fuel pressure sensor (Built into injector assembly) Monitors internal fuel pressure of common rail and sends signals to ECM
Pressure discharge valve Based on signals from ECM, opens valve when sudden deceleration occurs, or when engine switch is off to prevent fuel pressure from becoming too high
Pre-stroke control valve Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure


c.

Diagnostic trouble code (DTC) table for the common rail system:

HINT:

This table indicates typical DTC combinations for each malfunction occurrence.


Trouble Area Malfunction DTC No.
Injector assembly Open or short in injector circuit P0093*, P0201, P0202, P0203, P0204, P062D, P029D, P02A1, P02A5, P02A9
Stuck open P0093, P029D, P02A1, P02A5, P02A9
Stuck closed P0301, P0302, P0303, P0304
Fuel pressure sensor (Built into injector assembly) Open or short in fuel pressure sensor circuit or pressure sensor output fixed P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3, P13E1, P13E2, P13E6, P13E7
Pressure discharge valve Open or short in pressure discharge valve circuit P0088*, P0093*, P1229*, P1271, P1272
Stuck open P0093
Stuck closed P0088*, P1272
Pre-stroke control valve Open or short in pre-stroke control valve circuit P0627, P1229, P0088*
Stuck open P0088*, P1229
Common rail system (Fuel system) Fuel leaks in high-pressure area P0093

*: There may be no DTC output depending on the condition of the malfunction.


d.

Diagnostic trouble code description for the common rail system:

DTC No. Description
P0088 Internal fuel pressure too high (240000 kPa [2447 kgf/cm2, 34800 psi] or more)
P0093 Fuel leaks in high-pressure areas
P0201 Open or short in No. 1 injector circuit
P0202 Open or short in No. 2 injector circuit
P0203 Open or short in No. 3 injector circuit
P0204 Open or short in No. 4 injector circuit
P029D Cylinder 1 - Injector Leaking
P02A1 Cylinder 2 - Injector Leaking
P02A5 Cylinder 3 - Injector Leaking
P02A9 Cylinder 4 - Injector Leaking
P0301 Cylinder 1 misfire detected
P0302 Cylinder 2 misfire detected
P0303 Cylinder 3 misfire detected
P0304 Cylinder 4 misfire detected
P0627 Open or short in pre-stroke control valve circuit
P062D ECM internal error
P1229 Fuel over-feed
P1271 Open or short in pressure discharge valve circuit
P1272 Pressure discharge valve stuck close
P13A1 Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU)
P13A2 Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU)
P13A6 Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU)
P13A7 Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU)
P13AB Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU)
P13AC Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU)
P13B1 Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU)
P13B2 Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU)
P13E1 Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU)
P13E2 Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU)
P13E6 Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU)
P13E7 Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU)
P13A3 No. 1 injector assembly (fuel pressure sensor) circuit range/performance
P13A8 No. 2 injector assembly (fuel pressure sensor) circuit range/performance
P13AD No. 3 injector assembly (fuel pressure sensor) circuit range/performance
P13B3 No. 4 injector assembly (fuel pressure sensor) circuit range/performance
P167A No. 1 injector assembly communication malfunction
P167B No. 2 injector assembly communication malfunction
P167C No. 3 injector assembly communication malfunction
P167D No. 4 injector assembly communication malfunction
P168A No. 1 injector assembly internal malfunction
P168B No. 2 injector assembly internal malfunction
P168C No. 3 injector assembly internal malfunction
P168D No. 4 injector assembly internal malfunction



FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION


a.

When the cam rotates the roller is pushed up, and in turn the plunger is pushed upward as well. When the plunger is not pushed up by the cam, it is pushed back down by the spring.

W123656C01
0.656,0.396 0.844,0.677 true 2.229,1.302 1.656,1.49 true 2.021,1.771 1.646,1.917 true 2.01,2.229 1.656,2.229 true 2.135,2.448 1.667,2.677 true 2.052,3.031 1.635,3.24 true 0.51,0.25 0.833,0.427 0.323,0.177 10 false *1 1.49,1.417 1.802,1.573 0.313,0.156 10 false *2 1.49,1.833 1.802,1.99 0.313,0.156 10 false *3 1.49,2.146 1.802,2.302 0.313,0.156 10 false *4 1.479,2.594 1.792,2.75 0.313,0.156 10 false *5 1.479,3.135 1.792,3.292 0.313,0.156 10 false *6
*1 Pre-stroke Control Valve *2 Plunger
*3 Spring *4 Shoe
*5 Roller *6 Double Cam



b.

The ECM controls the timing of the pre-stroke control valve opening to regulate the fuel quantity. Consequently, the fuel pressure in the common rail is controlled to the target injection pressure.


c.

The longer the pre-stroke control valve remains open, the quantity of pressure-fed strokes will decrease, as well as the fuel discharge quantity.


d.

Pumping will start when the fuel pressure has become higher than the common rail pressure.

W123658C01
3.302,0.552 3.438,0.271 true 3.417,0.083 3.729,0.24 0.313,0.156 10 false *a
*a Return Fuel - -



e.

The less time the pre-stroke control valve remains open, the quantity of pressure-fed strokes will increase, as well as the fuel discharge quantity.


f.

Pumping will start when the fuel pressure has become higher than the common rail pressure.

W123657