DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
Primary / -
All Data / All data
Diesel General
Engine Control / Engine control system related data
Common Rail
Common Rail (All)
Diesel EGR / EGR system related data
Diesel Throttle / Diesel throttle system related data
VN Turbo / VN turbo related data
Diesel Exhaust / Exhaust system related data
Diesel Starting / "Difficult to start" related data
Diesel Rough Idle / "Rough idle" related data
Diesel Lack of Power / "Lack of power" related data
Diesel Knocking / "Knocking" relater data
Diesel Black Smoke / "Black Smoke" related data
Check Mode / Check mode
Monitor Status / Monitor status related data
Ignition / Not Applicable
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transaxle system related data
Vehicle Information / Vehicle information
Check the values by referring to the table below.
Normal Condition: If no idling conditions are specified, the shift lever should be in N, and the A/C switch and all accessory switches should be off.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | - |
| Target Idle Engine Speed | Target Idling Engine Speed | Min.: 0 rpm, Max.: 10000 rpm | - | - |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 6000 rpm | ·
50 to 400 rpm: Cranking ·
800 to 900 rpm: Idling with warm engine (L4 detection switch not in L4) |
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0%, Max.: 100% | ·
Idling: 6.6 to 14.2% ·
Running without load (3000 rpm): 15.5 to 24.0% |
Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100. |
| MAF | Air flow rate from mass air flow meter sub-assembly | Min.: 0 gm/sec, Max.: 400 gm/sec | Idling:
·
3 to 15 gm/sec (EGR on) ·
10 to 21 gm/sec (EGR off) Running without load (3000 rpm):
·
35 to 89 gm/sec (EGR on) ·
72 to 94 gm/sec (EGR off) |
Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc. |
| Atmosphere Pressure | Atmospheric pressure value | Min.: 0 kPa(abs), Max.: 255 kPa(abs) | Actual atmospheric pressure | ·
With the engine switch on (IG), when the difference between the atmospheric pressure sensor and intake manifold absolute pressure is 10 kPa or more, there is a malfunction in one of the sensors. ·
With the engine switch on (IG), when the atmospheric pressure is 0 kPa or 140 kPa, there is a malfunction in the sensor circuit. ·
Standard atmospheric pressure: 101 kPa. ·
For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure). |
| MAP | Absolute pressure inside intake manifold | Min.: 0 kPa, Max.: 320 kPa | Idling:
·
92 to 101 kPa (EGR on) ·
66 to 87 kPa (EGR off) Running without load (3000 rpm):
·
105 to 140 kPa (EGR on) ·
102 to 134 kPa (EGR off) |
·
When the engine switch on (IG) or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa). Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure. ·
Inspect while comparing with "Target Booster Pressure". ·
With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur. |
| Coolant Temp | Engine coolant temperature | Min.: -40°C, Max.: 140°C | After warming up engine: 70 to 90°C (158 to 194°F) | ·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. ·
After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal. |
| Intake Air | Intake air temperature | Min.: -40°C, Max.: 140°C | Equivalent to temperature at location of mass air flow meter sub-assembly | ·
After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal. ·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. |
| Intake Air Temp (Turbo) Supported | Intake air temp (Turbo) support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Intake Air Temp (Turbo) | Intake air temperature after intercooler | Min.: -40°C, Max.: 190°C | 70°C (158°F) or less | ·
This is the intake air temperature at the intake manifold (after the intercooler). ·
During fail-safe operation, the value is set to 165°C (329°F). As the value is set to a high temperature, the turbo pressure may be suppressed and there may be a lack of power. |
| Engine Run Time | Engine run time | Min.: 0 sec., Max.: 65535 sec. | Time after the engine switch turned to on (IG) | Time passed since the engine switch was turned to on (IG). |
| Initial Engine Coolant Temp | Initial engine coolant temperature | Min.: -40°C, Max.: 120°C | Engine coolant temperature when engine started | For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine. |
| Initial Intake Air Temp | Initial intake air temperature | Min.: -40°C, Max.: 120°C | Intake air temperature when engine started | - |
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 15 V | 11 to 14 V | ·
If 11 V or less, characteristics of some electrical components change. ·
Symptoms when out of range: ·
If 5 V or less, starting becomes difficult |
| Alternate Duty Ratio | Alternator generation duty ratio | Min.: 0%, Max.: 100% | ·
No electrical load at idling: 20 to 60% ·
High electrical load at idling: 100% |
·
This is outputs the alternator generation duty and is used to determine the electrical load. ·
Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction. ·
Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device such as the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, such as battery deterioration. |
| Glow Relay Request | Status of the glow relay request | ON or OFF | - | - |
| Glow Control Unit Duty | Glow plug controller duty | Min.: 0%, Max.: 127.5% | - | This is the ECM command. |
| Glow Indicator Supported | Glow indicator support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Glow Indicator | Status of the glow indicator | ON or OFF | - | - |
| Accel Position | Accelerator position status | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 0% ·
Accelerator pedal fully depressed: 100% |
·
"Accel Position" is the accelerator opening amount (%) for engine control use. ·
When the accelerator pedal position sensor output itself (Accel Sens. No.1 Volt %, Accel Sens. No.2 Volt %) is in the normal range, another actuator malfunction has caused the fail-safe function to restrict the accelerator. ·
Without cruise, ECT or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver. ·
Accelerator pedal released: 0% ·
Accelerator pedal fully depressed: 100% |
| Accel Sens. No.1 Volt % | Accelerator position No. 1 | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 10 to 22% ·
Accelerator pedal fully depressed: 52 to 90% |
Read value with engine switch on (IG) (do not start engine).
|
| Accel Sens. No.2 Volt % | Accelerator position No. 2 | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 24 to 40% ·
Accelerator pedal fully depressed: 68 to 99% |
Read value with engine switch on (IG) (do not start engine).
|
Diesel Throttle System
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Throttle Position Supported | Target throttle position support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target Throttle Position | Target throttle position | Min.: -128%, Max.: 127% | ·
Throttle valve fully closed: 0% ·
Throttle valve fully opened: 100% |
If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting. |
| Target Throttle Position #2 Supported | Target throttle position (No. 2) support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target Throttle Position #2 | Target No. 2 throttle position | Min.: -128%, Max.: 127% | - | - |
| Actual Throttle Position Supported | Actual throttle position support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual Throttle Position | Actual throttle position | Min.: -20%, Max.: 120% | Idling after engine warmed-up: 0 to 92% | Closing percentage of the throttle valve.
·
Fully closed: 0%. ·
Fully open: 100%.
Symptoms when out of range: ·
Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle ·
Stuck open: Loud turbocharging sound, bad vibration when engine is stopped ·
When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h. |
| Actual Throttle Position #2 Supported | Actual No. 2 throttle position support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual Throttle Position #2 | Actual No. 2 throttle position | Min.: -20%, Max.: 120% | - | - |
| Throttle Motor DUTY | Throttle motor duty | Min.: 0%, Max.: 100% | - | When the moving force to open and close the diesel throttle valve increases, the value of the Throttle Motor Duty increases. |
| Throttle Close Learning Val. | Throttle fully closed position learned value | Min.: 0 deg, Max.: 84 deg | 14 to 22 deg | ·
When the engine switch is turned from on (IG) to off and 5 seconds elapse, learning of "Throttle Close Learning Val." will be complete. ·
When "Throttle Close Learning Val." is outside of the normal range, a foreign object may lodged in the throttle valve. ·
If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present. However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed. |
| Throttle Sensor Volt % | Absolute throttle position sensor | Min.: 0%, Max.: 100% | ·
Engine switch on (IG): 60 to 100% ·
Warmed-up and idling: 8 to 100% |
·
Throttle position sensor output voltage is converted using 5 V = 100%. ·
When fully closed: 20%. ·
When fully open: 82%. ·
When the engine switch is turned from off to on (IG), the throttle valve fully opens once. ·
When the engine switch is turned from on (IG) to off, the throttle valve fully closes once. Symptoms when out of range: ·
Stuck closed: Engine stall, difficult to start, rough idling, lack of power, black smoke, white smoke ·
Stuck open: Loud turbocharging sound, bad vibration when engine is stopped ·
When the ECM detects a malfunction with the diesel throttle (MIL on), engine power is restricted but city driving is possible. |
| Throttle Motor DUTY | Throttle motor duty | Min.: 0%, Max.: 100% | Warmed-up and idling: 0 to 80% | ·
When drive requests to open and close the diesel throttle valve increase, the throttle motor duty value increases. ·
Since the throttle valve opening and closing directions cannot be determined when the throttle motor duty value is high during drive control, the opening and closing directions are determined from the throttle target opening angle and throttle actual opening angle. ·
If the throttle motor duty value continues to be high, there may be an operation malfunction due to deposits in the throttle. |
Diesel Injection System
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Injection Volume | Injection volume | Min.: 0 mm3/st, Max.: 1279.98 mm3/st | Idling: 3 to 15 mm3/st | ·
Injection amount for each combustion. ·
If injector assemblies are clogged fuel quality is poor, the fuel filter element assembly is clogged, or engine friction increases, "Injection Volume" will increase. ·
If there is a malfunction due to low turbocharger pressure or a low intake air volume, the injection volume is limited and there is a lack of power. |
| Total Injection Volume | Total injection volume | Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 3 to 15 mm3/st | ·
Displays the total fuel injection volume for all cylinders (includes the pilot, main and after injection timing). ·
This calculates the most recent fuel injection volume for each injector (Injection Volume #1 to #4). For example, #1 → #3 → #4 → #2 → #1, etc. (the value differs depending on engine speed and sampling timing). ·
This can be acquired from the output value from the pressure sensors built into the injectors. This is an estimate of the actual injection volume based on the pressure drop behavior due to fuel injection. |
| Inj. FB Vol. for Idle | Idle stability status integral control volume | Min.: -80 mm3/st, Max.: 79 mm3/st | -20 to 30 mm3/st | ·
When the actual engine speed does not match the target idling speed, this corrects the injection volume. If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning. ·
Only calculated and reflected at idle. |
| Injection Feedback Val #1 | Injection volume correction for No. 1 injector assembly | Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | ·
When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder. Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased. ·
"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion. ·
Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.
|
| Injection Feedback Val #2 | Injection volume correction for No. 2 injector assembly | Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | Same as Injection Feedback Val #1 |
| Injection Feedback Val #3 | Injection volume correction for No. 3 injector assembly | Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | Same as Injection Feedback Val #1 |
| Injection Feedback Val #4 | Injection volume correction for No. 4 injector assembly | Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | Same as Injection Feedback Val #1 |
| Injection Volume #1 | Injection volume | Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 3 to 15 mm3/st | ·
Displays the fuel injection volume for each injector (includes the pilot, main and after injection timing). ·
Perform an inspection while comparing it with the injection volume. ·
This can be acquired from the output value from the pressure sensors built into the injectors. This is an estimate of the actual injection volume based on the pressure drop behavior due to fuel injection. ·
The compensation injection volume (Injection Feedback Val) for each cylinder is added to these values. Therefore, the value between cylinders may be different. |
| Injection Volume #2 | Injection volume | Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 3 to 15 mm3/st | Same as Injection Volume #1 |
| Injection Volume #3 | Injection volume | Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 3 to 15 mm3/st | Same as Injection Volume #1 |
| Injection Volume #4 | Injection volume | Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 3 to 15 mm3/st | Same as Injection Volume #1 |
| Pre Injection Period | Pre injection period | Min.: 0 μs, Max.: 65535 μs | - | - |
| Pilot 1 Injection Period | Pilot 1 injection period | Min.: 0 μs, Max.: 65535 μs | Idling: 100 to 600 μs | Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur. |
| Pilot 2 Injection Period | Pilot 2 injection period | Min.: 0 μs, Max.: 65535 μs | Idling:
·
100 to 500 μs (Atmosphere pressure higher than 85 kPa) ·
100 to 600 μs (Atmosphere pressure 85 kPa or less) |
Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur. |
| Main Injection Period | Main injection period | Min.: 0 μs, Max.: 65535 μs | Idling:
·
200 to 1000 μs (Atmosphere pressure higher than 85 kPa) ·
200 to 1000 μs (Atmosphere pressure 85 kPa or less) |
·
When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0. ·
When the engine will not start, confirm that injection is performed. ·
When P0093, P0627 or P062D is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.
|
| After Injection Period | After injection period | Min.: 0 μs, Max.: 65535 μs | - | Check to see if "After Injection Period" is not zero when the following symptoms occur:
Black smoke, poor driveability. |
| Pre Injection Timing | Pre injection timing | Min.: -210 deg(CA), Max.: 301.9 deg(CA) | - | - |
| Pilot 1 Injection Timing | Pilot 1 injection timing | Min.: -210 deg(CA), Max.: 301.9 deg(CA) | Idling after engine warmed up and vehicle under normal atmospheric pressure: 13.8 to 8.0 deg(CA) | ·
Negative values indicate values after top dead center (ATDC). ·
Positive values indicate values before top dead center (BTDC). |
| Pilot 2 Injection Timing | Pilot 2 injection timing | Min.: -210 deg(CA), Max.: 301.9 deg(CA) | Idling after engine warmed up and vehicle under normal atmospheric pressure: 7.5 to 2.0 deg(CA) | ·
Negative values indicate values after top dead center (ATDC). ·
Positive values indicate values before top dead center (BTDC). |
| Main Injection Timing | Main injection timing | Min.: -210 deg(CA), Max.: 301.9 deg(CA) | Idling after engine warmed up and vehicle under normal atmospheric pressure: -2.0 to -7.0 deg(CA) | ·
Negative values indicate values after top dead center (ATDC). ·
Positive values indicate values before top dead center (BTDC). |
| After Injection Timing | After injection timing | Min.: -210 deg(CA), Max.: 301.9 deg(CA) | - | ·
Negative values indicate values after top dead center (ATDC). ·
Positive values indicate values before top dead center (BTDC). |
| i-ART Learning Status #1 | i-ART learning status | OK or NG | OK: Normal | ·
If the learned value for the i-ART injection volume stays at the minimum or maximum, this flag changes to NG. ·
If the i-ART injection volume learned value reaches the minimum or maximum and the injection volume does not become the requested amount unless an update is performed, this flag changes to NG. ·
This item is reset when the engine switch is turned off. |
| i-ART Learning Status #2 | i-ART learning status | OK or NG | OK: Normal | Same as i-ART Learning Status #1 |
| i-ART Learning Status #3 | i-ART learning status | OK or NG | OK: Normal | Same as i-ART Learning Status #1 |
| i-ART Learning Status #4 | i-ART learning status | OK or NG | OK: Normal | Same as i-ART Learning Status #1 |
| i-ART Learning Status History #1 | i-ART learning status history | Min.: 0 Trip, Max.: 255 Trip | 0 Trip | ·
This is history data of flags set when the learned value for each injector is stuck. ·
This item records the number of trips that i-ART Learning Status became NG (when the learning status of i-ART is abnormal, this history displays 1 or higher). ·
If any of the counters is 1 or more when there are symptoms of rough idle, black smoke, white smoke, poor drivability, poor output, knocking, or starting trouble, or when any related DTCs are stored, the problem may have occurred due to foreign matter in the fuel system. Replace the fuel filter element assembly, etc. and perform repairs according to the troubleshooting procedures. ·
This item is reset when the battery cable is disconnected or when DTCs are cleared. |
| i-ART Learning Status History #2 | i-ART learning status history | Min.: 0 Trip, Max.: 255 Trip | 0 Trip | Same as i-ART Learning Status History #1 |
| i-ART Learning Status History #3 | i-ART learning status history | Min.: 0 Trip, Max.: 255 Trip | 0 Trip | Same as i-ART Learning Status History #1 |
| i-ART Learning Status History #4 | i-ART learning status history | Min.: 0 Trip, Max.: 255 Trip | 0 Trip | Same as i-ART Learning Status History #1 |
| Injector Leaking Count #1 | Injector leaking count | Min.: 0, Max.: 255 | 0 | ·
The number of times each injector leaked ·
When the drop in pressure (change in slope) is larger than the threshold and there is a time difference in the drop in pressure between this cylinder and other cylinders, the system determines that the injector leaked. ·
If any of the counters is 1 or more when there are symptoms of rough idle, black smoke, white smoke, poor drivability, poor output, knocking, or starting trouble, or when any related DTCs are stored, the problem may have occurred due to foreign matter in the fuel system. Replace the fuel filter element assembly, etc. and perform repairs according to the troubleshooting procedures. ·
This item is reset when the battery cable is disconnected or when DTCs are cleared. |
| Injector Leaking Count #2 | Injector leaking count | Min.: 0, Max.: 255 | 0 | Same as Injector Leaking Count #1 |
| Injector Leaking Count #3 | Injector leaking count | Min.: 0, Max.: 255 | 0 | Same as Injector Leaking Count #1 |
| Injector Leaking Count #4 | Injector leaking count | Min.: 0, Max.: 255 | 0 | Same as Injector Leaking Count #1 |
| Injection Pressure Correction | Injection pressure feedback compensation volume | Min.: -640 mm3/st, Max.: 639.98 mm3/st | -100 to 100 mm3/st at standard temperature | ·
When the (actual) fuel pressure is equal to the target fuel pressure, this value becomes 0. ·
This indicator can be used for diagnosing fuel supply pump assembly related malfunctions. ·
When this value (absolute value) is large, it indicates that the difference between the actual and target fuel pressure is also large. ·
A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure. ·
When the pre-stroke control valve is malfunctioning, it causes rail overpressure, and this value slips to the negative volume side. ·
Injection Pressure Correction displays the value calculated by the ECM. |
| PCV Energization Timing | Pre-stroke control valve energization timing | Min.: 0 deg(CA), Max.: 639.9 deg(CA) | Idling: 0 to 180 deg(CA) | ·
Displays the pre-stroke control valve energization timing. ·
When Common Rail Pressure is higher than Target Common Rail Pressure and the fuel supply pump assembly is not commanded to discharge, the value of PCV Energization Timing is -1. ·
When the fuel supply pump assembly is commanded to discharge, PCV Energization Timing changes to a value between 70 and 180. The larger the value, the smaller the amount of discharge. ·
PCV Energization Timing displays the value calculated by the ECM. |
| Injection EDU Relay Request | Status of the EDU relay request | ON or OFF | ON: EDU relay ON | - |
| Target Common Rail Pressure Supported | Target common rail pressure support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target Common Rail Pressure | Target common rail pressure | Min.: 0 kPa(abs), Max.: 250000 kPa(abs) | 20000 to 220000 kPa when engine running | ·
Inspect the (actual) fuel pressure, comparing it with the common rail target value. ·
Considered normal when the actual fuel pressure is within 5000 kPa of the target fuel pressure under stable conditions when idling after warm up the engine. |
| Common Rail Pressure Supported | Common rail pressure support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Common Rail Pressure | Actual common rail pressure | Min.: 0 kPa(abs), Max.: 250000 kPa(abs) | Idling: 30000 to 50000 kPa | ·
Common Rail Pressure is the actual common rail fuel pressure. ·
Inspect by comparing the fuel pressure with the target fuel pressure. ·
When in a stable condition such as when idling after warm up the engine, the fuel pressure is within 5000 kPa of the target fuel pressure. ·
The ECM uses fuel pressure for feedback control of the target fuel pressure via the fuel supply pump assembly. The injection amount is determined based on the injection timing and fuel pressure. Also, the spray pattern is selected based on the fuel pressure. ·
For startup, at least 25000 kPa of fuel pressure is needed (take care as there is a response lag when the pressure rises). ·
When the fuel pressure is below 25000 kPa, it may cause rough idling. ·
When the fuel pressure has decreased by 20000 kPa from the target fuel pressure, there may be a lack of power. ·
If actual fuel pressure is 5000 kPa higher than the target fuel pressure, P1229 will be stored. When the actual fuel pressure is lower than the target fuel pressure, "P1608 Lack of Power" may be detected depending on the degree of deviation from the target pressure. ·
When the fuel pressure is higher than 240000 kPa, DTC P0088 will be stored. |
| Fuel Pressure #1 | Fuel pressure | Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | ·
Displays the fuel pressure for each injector. ·
The output voltage from the pressure sensor in each injector is converted to a pressure value using the adjustment value for each cylinder which is read from the memory built into the injectors. ·
This pressure value is not for pressure control, and it is influenced by the pressure pulsation due to fuel injection. Therefore, do not use it for comparing with Target Common Rail Pressure. Use Common Rail Pressure instead for comparing with Target Common Rail Pressure. |
| Fuel Pressure #2 | Fuel pressure | Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Same as Fuel Pressure #1 |
| Fuel Pressure #3 | Fuel pressure | Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Same as Fuel Pressure #1 |
| Fuel Pressure #4 | Fuel pressure | Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Same as Fuel Pressure #1 |
| Fuel Temperature Supported | Fuel temperature support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Fuel Temperature | Fuel temperature | Min.: -40°C, Max.: 140°C | Actual fuel temperature | After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature. |
| Fuel Temperature #1 | Fuel temperature | Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 30 to 90°C (86 to 194°F) | ·
Displays the fuel temperature of each injector. ·
The output voltage from the pressure sensor in each injector acquired via INJ communication is converted to a temperature value using the adjustment value for each cylinder which is read from the memory built into the injectors. ·
After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature. |
| Fuel Temperature #2 | Fuel temperature | Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 30 to 90°C (86 to 194°F) | Same as Fuel Temperature #1 |
| Fuel Temperature #3 | Fuel temperature | Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 30 to 90°C (86 to 194°F) | Same as Fuel Temperature #1 |
| Fuel Temperature #4 | Fuel temperature | Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 30 to 90°C (86 to 194°F) | Same as Fuel Temperature #1 |
| Injection Volume (Cylinder1) | Injection volume (cylinder 1) | Min.: 0 ml, Max.: 2.047 ml | - | This is the injection volume for 10 injections. |
| Pressure Discharge Valve | Pressure discharge valve operation | ON or OFF | ON: Pressure discharge valve open | This is the ECM command. |
| Pump Difference Angle Learning Value | Supply pump difference angle learning value | Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | -3 to 3 deg(CA) | ·
Learns the installation difference angle of the fuel supply pump assembly on the engine. ·
When Pump Difference Angle Learning Value is below -3 deg(CA) or more than 3 deg(CA), check Target Common Rail Pressure and Common Rail Pressure. ·
Pump Difference Angle Learning Value displays the value calculated by the ECM. |
EGR System
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target EGR Valve Pos Supported | Target EGR valve pos support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target EGR Valve Pos | EGR valve target opening amount | Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 90% | ·
Fully closed: 0%. ·
Fully open: 100%. ·
Used for comparison to "Actual EGR Valve Pos.". Symptoms when out of range: ·
When value is out of range and approaching 0%: mass air flow meter degradation, intake or exhaust system blockage ·
When value is out of range and approaching 100%: EGR pipe blockage |
| Target EGR Valve Pos #2 Supported | Target EGR valve pos #2 support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target EGR Valve Pos #2 | No. 2 EGR valve target opening amount | Min.: 0%, Max.: 100% | - | - |
| Actual EGR Valve Pos Supported | Actual EGR valve pos support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual EGR Valve Pos | EGR valve position | Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 90% | ·
Fully closed: 0%. ·
Fully open: 100%. ·
Inspect while comparing to "Target EGR Valve Pos". ·
Check the valve movement via the Active Test. ·
Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred. Symptoms when out of range: ·
EGR valve stuck open: Poor starts (engine does not stop), black smoke, white smoke, lack of power ·
EGR valve stuck closed: Increased turbo booster noise |
| EGR Rate Differential(Actual-Target) | Difference between actual EGR and target EGR while idling | Min.: -128%, Max.: 127% | - | ·
Percentage value (-100 to 100%), calculated as (Actual EGR - Target EGR) * 100 is displayed. ·
The maximum value is retained once idling is stabilized. Once the vehicle is no longer idling, such as when the vehicle is accelerated, the value resets to 0%. ·
A positive value indicates a large amount of EGR and a negative value indicates a small amount of EGR. |
| Actual EGR Valve Pos #2 Supported | Actual EGR valve pos #2 support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual EGR Valve Pos #2 | No. 2 EGR valve position | Min.: 0%, Max.: 100% | - | - |
| EGR Position Sensor | EGR position sensor | Min.: 0 V, Max.: 4.999 V | - | Displays the output voltage of the EGR valve position sensor. |
| EGR Motor Duty #1 | EGR valve actuation duty | Min.: 0%, Max.: 127.5% | Idling after engine warmed up: 0 to 100% | ·
To 0%: Close side EGR valve actuation. ·
To 100%: Open side EGR valve actuation. ·
When this value is large but the actual valve position does not reach the target valve position, there is an unable to open malfunction. |
| EGR Close Lrn. Val. | EGR fully closed position learned value | Min.: 0 V, Max.: 5 V | 0 to 1 V | ·
This value is the EGR position sensor output voltage. ·
When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area. ·
As the lower and upper limits are 0 V and 1 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.). |
| EGR Cooler Bypass VSV | Status of the Vacuum Switching Valve Assembly (for EGR bypass valve) | ON or OFF | ·
ON: Vacuum switching valve assembly (for EGR bypass valve) is ON ·
OFF: Vacuum switching valve assembly (for EGR bypass valve) is OFF |
·
When Vacuum Switching Valve Assembly (for EGR bypass valve) is ON, the value for EGR Cooler Bypass Position is Cooler and, when Vacuum Switching Valve Assembly (for EGR bypass valve) is OFF, the value for EGR Cooler Bypass Position is Bypass. ·
The Vacuum Switching Valve Assembly (for EGR bypass valve) is controlled by the ECM and the vacuum switching valve assembly (for EGR bypass valve) is opened and closed by the vacuum created by the vacuum pump. |
| EGR Cooler Bypass Position | Status of the EGR Cooler Bypass Position | Cooler or Bypass | ·
Cooler: Vacuum Switching Valve Assembly (for EGR bypass valve) is "ON" ·
Bypass: Vacuum Switching Valve Assembly (for EGR bypass valve) is "OFF" |
·
When Vacuum Switching Valve Assembly (for EGR bypass valve) is ON, the value for EGR Cooler Bypass Position is Cooler and, when Vacuum Switching Valve Assembly (for EGR bypass valve) is OFF, the value for EGR Cooler Bypass Position is Bypass. ·
The Vacuum Switching Valve Assembly (for EGR bypass valve) is controlled by the ECM and the vacuum switching valve assembly (for EGR bypass valve) is opened and closed by the vacuum created by the vacuum pump. |
VN Turbo System
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Booster Pressure Supported | Target booster pressure support | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target Booster Pressure | Target booster pressure | Target booster pressure/Min.: 0 kPa, Max.: 320 kPa | Driving vehicle on level surface at 3000 rpm with full load: 190 to 240 kPa | ·
Inspect while comparing with "MAP". ·
With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 second or more, a feeling of a lack of power will occur. ·
When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure". |
| Target VN Turbo Position Supported | Target VN turbo position supported | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target VN Turbo Position | Target VN turbo position | Min.: 0%, Max.: 100% | 0 to 96% | ·
When the nozzle vanes are fully closed (boost is applied), the value is 0%. ·
When the nozzle vanes are fully opened (boost is not applied), the value is 100%. |
| Target VN Turbo Position #2 Supported | Target VN turbo position #2 supported | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Target VN Turbo Position #2 | Target No. 2 VN turbo position | Min.: 0%, Max.: 100% | - | - |
| Actual VN Position Supported | Actual VN position supported | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual VN Turbo Position | Actual VN turbo position | Min.: 0%, Max.: 100% | 0 to 96% | ·
When the nozzle vane gets stuck or the movement is abnormal, the difference between this value and Target VN Turbo Position increases and the VN turbo motor output (duty) also increases. ·
Actual VN Turbo Position is controlled to match Target VN Turbo Position. |
| Actual VN Position #2 Supported | Actual VN position #2 supported | Unsupp or Supp | - | ·
Supp: The item is supported by the vehicle. ·
Unsupp: The monitor is not supported by the vehicle. |
| Actual VN Turbo Position #2 | Actual No. 2 VN turbo position | Min.: 0%, Max.: 100% | - | - |
| VN Position Sensor Out | VN position sensor output voltage | Min.: 0 V, Max.: 5 V | Idling after engine warmed-up: 1 to 4.5 V | VN Position Sensor Out displays the opening angle of the nozzle vane output by the sensor. |
| VN Motor Duty | VN turbo motor duty | Min.: 0%, Max.: 127.5% | 2 to 88% | If the vanes do not move smoothly, the duty will increase towards 100%. |
| VN Close Learn Value | VN turbo fully closed position learned value | Min.: 0 V, Max.: 5 V | 1 to 4.5 V | - |
| VN Turbo Type | VN turbo type | Not Avl, Commo, Vacuum, CAN Com, DC | DC | Indicates the VN turbo vane actuation method.
·
DC motor system. ·
Negative-pressure diaphragm system. ·
Step motor system. |
| VN Turbo Max Angle | VN turbo maximum opening amount | Min.: 0%, Max.: 100% | - | ·
The maximum vane opening amount is displayed in %. ·
The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed. |
| VN Turbo Min Angle | VN turbo minimum opening amount | Min.: 0%, Max.: 100% | - | ·
The maximum vane opening amount is displayed in %. ·
The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed. |
Diesel Exhaust
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Exhaust Temperature B1S1 Supported | Status of exhaust temperature B1S1 supported | Supp or Unsupp | Supp | If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature B1S1", as exhaust gas temperature sensors are not equipped on the vehicle. |
| Exhaust Temperature B1S1 | Exhaust gas temperature of upstream of the DOC catalyst | Min.: -40°C, Max.: 1000°C | Idling after engine warmed up: 50 to 400°C (122 to 752°F) | ·
If an open occurs in an exhaust gas temperature sensor circuit, 0°C (32°F) is displayed on the GTS. ·
If a short occurs in an exhaust gas temperature sensor circuit, 1000°C (1832°F) is displayed on the GTS. |
| Exhaust Temperature B1S2 Supported | Status of exhaust temperature B1S2 supported | Supp or Unsupp | Supp | If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature B1S2", as No. 2 exhaust gas temperature sensors are not equipped on the vehicle. |
| Exhaust Temperature B1S2 | Exhaust gas temperature of downstream of the DOC catalyst | Min.: -40°C, Max.: 1000°C | Idling after engine warmed up: 50 to 400°C (122 to 752°F) | ·
If an open occurs in an No. 2 exhaust gas temperature sensor circuit, 0°C (32°F) is displayed on the GTS. ·
If a short occurs in an No. 2 exhaust gas temperature sensor circuit, 1000°C (1832°F) is displayed on the GTS. |
| Exhaust Temperature B1S3 Supported | Status of exhaust temperature B1S3 supported | Supp or Unsupp | Unsupp | If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature B1S3", as No. 3 exhaust gas temperature sensors are not equipped on the vehicle. |
| Exhaust Temperature B1S3 | No. 3 exhaust gas temperature | Min.: -40°C, Max.: 1000°C | - | - |
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Signal | Starter signal | ON or OFF | ON: Cranking | Starter Signal condition:
·
ON: Starter is operating ·
OFF: Starter is not operating Cause of Out of Range: ·
OFF malfunction (engine switch (STA) is ON but the signal is OFF and the starter is operating): Wire harness is open or shorted to ground ·
ON malfunction (engine switch (STA) is off but the signal is ON and the starter is not operating): Wire harness is shorted to +B ·
Operation malfunction: engine switch malfunction, starter relay malfunction, starter malfunction, battery or battery cable is defective, or wire harness is open or shorted Symptoms when out of range: ·
Engine switch (STA) is ON but the starter does not operate: Starting is not possible ·
Engine switch (STA) is OFF but the starter continues to operate: STA signal malfunction (P0617) is stored |
| Power Steering Signal | Power steering switch signal | ON or OFF | - | - |
| Neutral Position SW Signal | Park/Neutral position switch status | ON or OFF | ON: Shift lever in neutral | - |
| Transfer L4 | L4 status of the transfer | ON or OFF | ON: 4WD control switch in 4L position | - |
| Stop Light Switch | Stop light switch | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
Stop light switch (STP) operation condition:
·
ON: Light is on (Brake pedal is depressed) ·
OFF: Light is off (Brake pedal is released) Cause of Out of Range: ·
OFF malfunction: Wire harness (stop light switch to ECM, stop light switch to +B) open or shorted to ground ·
ON malfunction: Wire harness (stop light switch to ECM) shorted to +B ·
Stop light switch Symptoms when out of range: Stop light switch malfunction DTC P0504 is stored |
| A/C Signal | A/C (Air Conditioner) signal | ON or OFF | ON: A/C on | Symptoms when out of range:
OFF malfunction (OFF even when A/C switch is turned on): ·
Engine speed decreases temporarily when the A/C is operating. |
| Immobiliser Communication | Immobiliser communication | ON or OFF | ·
ON: Normal ·
OFF: Engine cannot be started due to immobiliser communication malfunction |
Cause of Out of Range:
·
Use of a non-registered key ·
Key battery is fully depleted |
Check Mode (Check Mode)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Check Mode | Check mode | ON or OFF | ON: Check mode on | Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity. |
| SPD Test Result | Check mode result for vehicle speed sensor | Compl or Incmpl | - | Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the engine switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected. |
Test Result (Monitor Status)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | * |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | * |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | * |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | * |
| EGR/VVT Monitor | EGR/VVT monitor | Compl or Incmpl | - | * |
| O2S(A/FS) Heater Monitor | O2S(A/FS) heater monitor | Not Avl or Avail | - | * |
| O2S(A/FS) Heater Monitor | O2S(A/FS) heater monitor | Compl or Incmpl | - | * |
| O2S(A/FS) Monitor | O2S(A/FS) monitor | Not Avl or Avail | - | * |
| O2S(A/FS) Monitor | O2S(A/FS) monitor | Compl or Incmpl | - | * |
| A/C Monitor | A/C monitor | Not Avl or Avail | - | * |
| A/C Monitor | A/C monitor | Compl or Incmpl | - | * |
| 2nd Air Monitor | 2nd air monitor | Not Avl or Avail | - | * |
| 2nd Air Monitor | 2nd air monitor | Compl or Incmpl | - | * |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | * |
| EVAP Monitor | EVAP monitor | Compl or Incmpl | - | * |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | * |
| Heated Catalyst Monitor | Heated catalyst monitor | Compl or Incmpl | - | * |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | * |
| Catalyst Monitor | Catalyst monitor | Compl or Incmpl | - | * |
*:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the engine switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TC Terminal | TC terminal status | ON or OFF | - | - |
| # Codes(Include History) | Number of codes | Min.: 0, Max.: 255 | 0 | Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up. |
| MIL | MIL status | ON or OFF | OFF: MIL off | - |
| MIL ON Run Distance | Distance traveled with MIL on | Min.: 0 km, Max.: 65535 km | Distance traveled after DTC stored | ·
Distance traveled after a DTC is stored. ·
Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the GTS. |
| Running Time from MIL ON | Running time after MIL turns on | Min.: 0 min., Max.: 65535 min. | Running time after MIL turns on | ·
Engine run time since the MIL illumination. ·
Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the GTS. |
| Time after DTC Cleared | Time after DTC cleared | Min.: 0 min., Max.: 65535 min. | Time after DTCs cleared | Time elapsed since the DTCs were cleared (or shipment from the factory). |
| Distance from DTC Cleared | Distance driven after DTC cleared | Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | ·
Distance driven since the DTCs were cleared. ·
(Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred. |
| Warmup Cycle Cleared DTC | Warmup cycles after DTC cleared | Min.: 0, Max.: 255 | - | ·
Number of engine warmup since DTCs were cleared. ·
(Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred. |
| Dist Batt Cable Disconnect | Distance driven after battery cable disconnected | Min.: 0 km, Max.: 16777215 km | - | - |
| IG OFF Elapsed Time | Time after engine switch turned off | Min.: 0 min, Max.: 655350 min. | Cumulative time after engine switch turned off | - |
| OBD Requirements | OBD requirement | - | - | EOBD (Euro OBD) |
| Number of Emission DTC | Emissions-related DTCs | - | - | - |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | ON or OFF | - | When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. |
| Total Distance Traveled | Total distance traveled | Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) | Total distance vehicle driven after battery cable disconnected | - |
Diesel Starting
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed (Starter Off) | Engine speed when starter off | Min.: 0 rpm, Max.: 1594 rpm | - | Engine speed immediately after starting the engine. |
| Starter Count | Starter on count | Min.: 0, Max.: 255 | - | Number of times the starter turned on from the time the engine switch was turned to on (IG). |
| Run Dist of Previous Trip | Distance driven during previous trip | Min.: 0 km, Max.: 261 km | - | Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
| Glow Request Lighting Time | Glow Request Lighting Time | Min.: 0 ms, Max.: 33423 ms | - | ·
By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined. ·
If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off. |
| IG-ON Time | IG-ON Time | Min.: 0 ms, Max.: 33423 ms | - | ·
By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined. ·
If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off. |
Diesel Lack of Power
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MAF Low | Mass air flow Low | ON or OFF | OFF | ·
When DTC P1608 is output, this item indicates whether the cause of lack of power is related to the intake air amount. ·
This item indicates whether the intake air amount measured by the mass air flow meter sub-assembly was insufficient, which would cause the fuel injection volume to be reduced for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored. ·
This item is "ON" when the intake air amount is low due to blockage in the intake system, disconnection of hoses or an excessive amount of EGR, and also when the intake air amount is measured to be low due to deterioration of the mass air flow meter sub-assembly. |
| Boost Pressure Low | Status of the boost pressure low | ON or OFF | OFF | ·
When DTC P1608 is output, this item indicates whether the cause of lack of power is due to the boost pressure. ·
This item indicates whether the actual boost pressure was insufficient compared to the target boost pressure, which would cause the fuel injection volume to be reduced for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored. |
| Common Rail Pressure Low | Status of the common rail pressure low | ON or OFF | OFF | ·
When DTC P1608 is output, this item indicates whether the cause of lack of power is the common rail pressure. ·
This item indicates whether the actual common rail pressure was lower than the target pressure for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored. |
| Engine Coolant Temp High | Status of the engine coolant temp High | ON or OFF | OFF | ·
When DTC P1608 is output, this item indicates whether the cause of lack of power is due to a high engine coolant temperature. ·
This item indicates whether the fuel injection volume was reduced for a certain period of time due to a high engine coolant temperature (overheating). If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored. |
| MAF/Estimate MAF Ratio | Ratio of intake air amount to estimated intake air amount | Min.: 0, Max.: 2.55 | Engine speed 4000 rpm, EGR system off:
0.6 to 1.4 |
·
Even when the system is normal, the value may deviate from the range specified in Normal Condition for a short period of time (approximately 1 second). ·
This item indicates the ratio of the intake air amount to the estimated intake air amount. The estimated air amount is calculated using the intake manifold pressure and intake air temperature. ·
When DTC P1608 is stored, this item is useful in determining whether there is a problem in the turbocharger system or a disconnected or leaking pipe in the high pressure intake system when the boost pressure is insufficient. ·
When performing troubleshooting, this information is only valid when there is a high load (the diesel throttle is fully open) and the EGR system is off. |
Diesel Rough Idle
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Compression Leakage Count | Compression leakage count | Min.: 0, Max.: 255 | 0 | When the counter displays 1 or higher during an engine stall, startability malfunction or rough idle, it may be the result of pressure loss caused by deposits jamming the valve, etc. |
| Plural Cylinders Rough Idle | Status of the plural cylinders rough idle | ON or OFF | OFF | Indicates multiple cylinders are the cause of rough idling when ON. |
| Rough Idle #1 | Status of the rough idle #1 | ON or OFF | OFF | ·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON. ·
This item indicates cylinders which are likely to be the cause of rough idle. |
| Rough Idle #2 | Status of the rough idle #2 | ON or OFF | OFF | Same as Rough Idle #1 |
| Rough Idle #3 | Status of the rough idle #3 | ON or OFF | OFF | Same as Rough Idle #1 |
| Rough Idle #4 | Status of the rough idle #4 | ON or OFF | OFF | Same as Rough Idle #1 |
| Electric Duty Feedback Value | Electric load feedback value | Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 7 mm3/st | Expected injection volume increase after the electrical load turns from off to on. |
| A/C Duty Feedback Value | A/C load feedback value | Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 3.7 mm3/st | Expected injection volume increase after the A/C turns from off to on. |
| PS Duty Feedback Value | Power steering load feedback value | Min.: 0 mm3/st, Max.: 39.8 mm3/st | 3.2 mm3/st | Expected injection volume increase after the power steering turns from off to on. |
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Starting Time | Engine starting time | Min.: 0 ms, Max.: 267000 ms | - | ·
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm. ·
This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms. |
| Minimum Engine Speed | Minimum engine speed | Min.: 0 rpm, Max.: 51199 rpm | - | - |
| Initial Engine Battery Minimum Voltage | Lowest battery voltage at startup | Min.: 0 V, Max.: 25.5 V | - | - |
| Swirl Control Valve VSV | Status of vacuum switching valve (for swirl control valve) | ON or OFF | ON: Vacuum switching valve (for swirl control valve) is ON | - |
| ACT VSV | A/C cut status for Active Test | ON or OFF | - | "Control the A/C Cut Signal" Active Test support data. |
| Brake Override System | Brake override system status | ON or OFF | ON: Brake override system operating | - |
| Immobiliser Fuel Cut History | Immobiliser fuel cut history | ON or OFF | OFF | If Immobiliser Fuel Cut History was "ON" when DTC P1604 (Startability Malfunction) was stored, the engine could not be started due to the immobiliser. |
| Fuel Remaining Volume | Fuel remaining volume | Min.: 0%, Max.: 100% | - | - |
Vehicle Information
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Model Code | Model code | - | - | Used for identifying the model code: GUN## |
| Engine Type | Engine type | - | - | Used for identifying the engine type: 1GDFTV |
| Cylinder Number | Number of cylinders | Min.: 0, Max.: 255 | - | Used for identifying the number of cylinders: 4 |
| Transmission Type | Transmission type | - | - | Used for identifying transmission type:
·
MT: Manual transmission ·
ECT 6th: Automatic transmission |
| Transmission Type2 | Transmission type | - | N/A | Unused |
| Destination | Destination | - | - | Identifying destination |
| Model Year | Model year | Min.: 1900, Max.: 2155 | - | Used for identifying the model year: 20## |
| System Identification | System identification | - | - | Used for identifying the engine system |
Compression
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed of Cyl #1 | Engine speed for No. 1 cylinder | Min.: 0 rpm, Max.: 51199 rpm | Engine speeds of all cylinders almost same | ·
Output only when the "Check the Cylinder Compression" Active Test is performed. ·
Indicates the speed of each cylinder when cranking. Example - Normal: Engine speeds of all cylinders are approximately equal. When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #4" is approximately 200 rpm. Symptoms when out of range: When the engine speeds of all cylinders are not equal, idling will be rough. |
| Engine Speed of Cyl #2 | Engine speed for No. 2 cylinder | Min.: 0 rpm, Max.: 51199 rpm | Engine speeds of all cylinders almost same | Same as Engine Speed of Cyl #1 |
| Engine Speed of Cyl #3 | Engine speed for No. 3 cylinder | Min.: 0 rpm, Max.: 51199 rpm | Engine speeds of all cylinders almost same | Same as Engine Speed of Cyl #1 |
| Engine Speed of Cyl #4 | Engine speed for No. 4 cylinder | Min.: 0 rpm, Max.: 51199 rpm | Engine speeds of all cylinders almost same | Same as Engine Speed of Cyl #1 |
| Av Engine Speed of All Cyl | Average engine speed for all cylinders | Min.: 0 rpm, Max.: 51199 rpm | - | ·
Output only when the Active Test "Check the Cylinder Compression" is performed. ·
Indicates the average engine speed of all cylinders during cranking. |
Automatic Transmission (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
| Pattern Switch (PWR/M) | PWR mode status | ON or OFF | ·
ON: PWR mode on ·
OFF: PWR mode off |
- |
| Shift SW Status (R Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported | Supp or Unsupp | - | - |
| Shift SW Status (N,P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) or "+" shift paddle operated and held (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) or "+" shift paddle not operated (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) or "-" shift paddle operated and held (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) or "-" shift paddle not operated (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in D, S, "+" or "-" ·
OFF: Shift lever not in D, S, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
Various Vehicle Conditions 5 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ECO Switch | Combination switch status | ON or OFF | ·
ON: Combination switch being turned and held at ECO position ·
OFF: Combination switch not turned |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the VSV for Swirl Control Valve | Activate the vacuum switching valve (for swirl control valve) | ON/OFF | Test is possible when the following conditions are met:
·
Engine switch on (IG). ·
Engine is idling. |
| Control the A/C Cut Signal | Control the A/C signal | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | - |
| Control the EGR Step Position | Control the electric EGR control valve assembly | 1 to 100% | Test is possible when the following conditions are met:
·
Engine switch on (IG). ·
Engine is stopped. |
| Test the Fuel Leak | Pressurize the common rail interior and check for fuel leaks | Stop/Start | ·
Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when Start is selected ·
Above conditions preserved while test is Start
|
| Activate the Pre-stroke Control Valve | Activates the pre-stroke control valve | Open/Close | Test is possible when the following conditions are met:
·
Engine switch on (IG). ·
Engine is stopped. ·
Shift lever in neutral |
| Activate the EGR Valve Close | Activate the electric EGR control valve assembly | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Activate the VSV for EGR Cooler Bypass | Activate the vacuum switching valve assembly (for EGR bypass valve) | Bypass/OFF/Cooler | Test is possible when the following conditions are met:
·
Engine warmed up ·
Engine is idling ·
Shift lever in neutral If performing the Active Test continuously, it must be finished within 5 minutes. |
| Test the Turbo Charger Step Motor | Activate the turbocharger sub-assembly | 0 to 60% | Test is possible when the following conditions are met:
·
Engine switch on (IG). ·
Engine is stopped. |
| Activate the VN Turbo Open | Activate the turbocharger sub-assembly | ON/OFF | Confirm that the engine is running. |
| Diesel Throttle Target Angle | Control the diesel throttle valve | 10 to 100% | Test is possible when the following conditions are met:
·
Engine switch on (IG). ·
Engine is stopped. |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | ON/OFF | Fuel injection is stopped while the test is ON.
·
Confirm that the vehicle is stopped and the engine is idling. ·
If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning. |
| Check the Cylinder Compression | Check the cylinder compression pressure* | ON/OFF | Fuel injection stops in all cylinders. |
*: When cranking the engine, the Active Test measures the speed of each cylinder. In this Active Test, the fuel of all cylinders is cut when the engine is cranked for approximately 10 seconds.
At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.
If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4 and Av Engine Speed of All Cyl.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded during the Active Test.
While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
After performing the above procedure, the "Check the Cylinder Compression" Active Test will start. Fuel injection for all cylinders is prohibited and the engine speed measurement of each cylinder enters standby mode.
Crank the engine for about 10 seconds.
Continue to crank the engine until the values change from the default value (51199 rpm).
Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the GTS.
At first, the GTS display will show the engine speed measurement of each cylinder to be extremely high. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.
After the "Check the Cylinder Compression" Active Test is turned on, it will automatically turn off after 255 seconds.
When the "Check the Cylinder Compression" test is off and the engine is cranked, the engine will start.
If the "Check the Cylinder Compression" test needs to be performed after it is turned on and performed once, press "EXIT" to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.
Use a fully-charged battery.
Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.
SYSTEM CHECK
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility.
| Tester Display | Diagnostic Note |
|---|---|
| Pressure Discharge Valve Check* | ·
Malfunctions can be determined by checking the fuel pressure when performing a forced operation of the pressure discharge valve. ·
Use when troubleshooting fuel pressure control malfunctions and abnormal combustion noise. |
| DOC Removal Check Mode | ·
Used when removing the exhaust manifold converter sub-assembly removal and troubleshooting diesel oxidation catalyst (DOC) loss of function. ·
After repairing the exhaust manifold converter, perform post injection and check that the catalyst warms up. ·
The repair condition can be determined by performing DOC Removal Check Mode, and then using All Readiness. |
*: Activate the Pressure Discharge Valve Check
This is the procedure for troubleshooting fuel pressure control malfunctions and combustion problems.
Malfunctions can be determined by checking the fuel pressure when performing a fuel cut and operating the pressure discharge valve with the GTS.
During "Pressure Discharge Valve Check", the GTS measures the fuel pressure while the engine is running, after the engine is stopped, and after the pressure discharge valve operates.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Confirm the following conditions:
Engine is idling.
Vehicle is stopped.
Fuel pressure is not extremely high (below 100000 kPa).
Fuel pressure is not extremely low (higher than 26000 kPa).
Fuel pressure sensor is normal.
Battery voltage is higher than 8 V.
When the common rail pressure is unstable, the fuel pressure may decrease to a level where the test cannot be performed. In this situation, wait until the common rail pressure meets the test condition, and then perform the test.
Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.
| Tester Display |
|---|
| Pressure Discharge Valve Check |
Press "Next".
Press "Next" again to proceed.
Select the check type "Valve Check for Graph".
Press "Next" again to proceed.
Press "Start" again to proceed.
*1: When "Start" is pressed, the pressure discharge valve check begins.
*2: If "Save" is pressed after the pressure discharge valve check, the data recorded during the valve check can be saved.
Select the check type "Close to Open Check" or "Always Closed Check".
"Close to Open Check" opens the pressure discharge valve after the engine stops.
"Always Closed Check" holds the pressure discharge valve closed during the check.
Press "Next".
Perform troubleshooting based on the measurement results.
During "Close to Open Check", if there is no large change in fuel pressure when the pressure discharge valve is closed while the engine is running and after the engine is stopped, and if the value is 0 kPa when the pressure discharge valve is open, the system is normal.
Perform "Always Closed Check" if the value is not 0 kPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.
If the fuel temperature is high, perform "Pressure Discharge Valve Check" after the fuel has cooled to the outside air temperature.
If a large amount of fuel is leaking, the fuel pressure decreases when the engine is stopped. However, the condition of the pressure discharge valve can still be determined by comparing the measurement results of "Close to Open Check" and "Always Closed Check".