Home › Engine / Hybrid System › 1GD-FTV FUEL › FUEL TANK › from 2016.10
RM33K0E _51 Engine / Hybrid System _043571 1GD-FTV FUEL _0222091 FUEL TANK A

1GD-FTV FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 77310A 3.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77641A 4.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A339621

Remove the 5 nuts and No. 1 fuel tank protector from fuel tank assembly.


Hide 77209F 5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE

a.
A339538

Slide the 2 clamps and disconnect the 2 fuel hoses from the fuel tank main tube sub-assembly and fuel tank return tube.


Hide 6.DISCONNECT NO. 1 EVAPORATION TUBE SUB-ASSEMBLY

a.
A339625

Disconnect the No. 1 evaporation tube sub-assembly from the fuel tank filler pipe sub-assembly.


Hide 7.DISCONNECT FUEL TANK BREATHER HOSE

a.
A339623

Slide the clamp and disconnect the fuel tank breather hose from the fuel tank filler pipe sub-assembly.


Hide 77213B 8.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A339624

Loosen the clamp and disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe sub-assembly.


Hide 9.REMOVE FUEL TANK ASSEMBLY

CAUTION:

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Using an engine lifter and attachments, support the fuel tank assembly.


b.
A339626

Remove the 3 bolts and disconnect the 3 fuel tank bands.


c.

Remove the 3 clips, 3 fuel tank band pins and 3 fuel tank bands.

HINT:

Move the fuel tank assembly just enough to remove the fuel tank band pins.



d.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wire harness.



e.
A339627C01
1.927,3.188 2.313,3.188 true 1.979,3.813 2.219,4.042 2.219,4.042 2.354,4.042 true 1.208,4.094 1.594,4.094 true 2.375,3.094 2.583,3.26 0.208,0.167 10 false *1 1.01,4.01 1.208,4.177 0.198,0.167 10 false *2 2.396,3.958 2.594,4.125 0.198,0.167 10 false *3
*1 Fuel Tank Cushion
*2 Wire Harness
*3 Fuel Tank Assembly


Fold back approximately half of each fuel tank cushion so that the wire harness can be removed in the step below.


f.
A339628

Detach the wire harness from the 6 clamps shown in the illustration.


g.

Disconnect the fuel sender gauge connector from the fuel tank vent tube assembly.


Hide 77697 10.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A339629C01
0.719,2.063 0.906,2.229 0.188,0.167 10 false 1 1.677,2.063 1.865,2.229 0.188,0.167 10 false 2 2.635,2.063 2.823,2.229 0.188,0.167 10 false 3
V100135

Fuel Tank Bolt
V100136

Nut


Remove the 2 nuts.


b.

Using needle-nose pliers, remove the 4 fuel tank bolts shown in the illustration, and then remove the No. 1 fuel tank heat insulator.


Hide 77652A 11.REMOVE FUEL TANK CUSHION

a.
A339630C01
0.49,0.313 2.948,0.313 2.948,0.313 2.948,0.76 true 0.979,0.802 0.979,0.313 true 2.25,0.802 2.25,0.313 true 0.25,0.229 0.448,0.396 0.198,0.167 10 false *1
*1 Fuel Tank Cushion


Remove the 3 fuel tank cushions from the fuel tank assembly.


Hide 77010 12.REMOVE FUEL TANK VENT TUBE ASSEMBLY

a.
A339553

Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube from the fuel tank vent tube assembly.

NOTICE:
A339604C01
1.167,0.25 1.25,0.25 1.25,0.25 1.417,0.5 true 2.25,0.5 2.417,0.333 2.417,0.333 2.5,0.333 true 2.083,1.063 2.417,1.313 2.417,1.313 2.583,1.313 true 0.927,1.365 0.927,1.198 0.927,1.198 1.427,1.198 true 0.76,1.365 1.427,1.365 true 0.938,0.167 1.156,0.344 0.219,0.177 10 false *a 2.563,0.24 2.781,0.406 0.219,0.167 10 false *b 0.531,1.271 0.74,1.448 0.208,0.177 10 false *c 2.646,1.229 2.875,1.406 0.229,0.177 10 false *d
*a Fuel Tube Joint
*b Fuel Tube
*c O-Ring
*d Tube Joint Clip


·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend or twist the nylon tube.

·

Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tank main tube sub-assembly and fuel tank return tube.




b.

Remove the fuel pump gauge retainer from the fuel tank assembly.

i.
A391907C01
0.219,3.104 0.458,3.104 0.458,3.104 0.917,2.802 true 2.74,1.833 2.854,2.24 2.854,2.24 3.094,2.24 false 0.99,2.375 1.885,3.073 1.885,3.073 2.125,3.073 true 3.115,2.125 3.427,2.281 0.313,0.156 10 false *a 2.156,2.958 2.469,3.115 0.313,0.156 10 false *b 0.063,2.99 0.375,3.146 0.313,0.156 10 false *c
*a SST (Plate)
*b SST (Claw)
*c Insertion point
V100135

SST (Bolt)


Set the 2 claws, 2 bolts and plate of SST on the fuel pump gauge retainer.

SST
09808-14031  (09808-01010, 09808-01020, 09808-01030, 09808-01090)
09808-01071  

HINT:

Securely insert the ends of SST into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing the claws of SST into the insertion points in the fuel pump gauge retainer, tighten the bolts of the claws.


iii.

Attach the handle of SST.


iv.
A387332C01
2.708,1.76 2.708,1.469 true 2.635,1.75 2.865,1.906 0.229,0.156 10 true *a
*a Insertion point


Check once more that the tip of SST is securely inserted into the insertion area of the fuel pump gauge retainer as shown in the illustration.


v.

While lightly pressing down on SST so it does not come off the fuel pump gauge retainer, slowly turn the handle and remove the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel pump gauge retainer will place excessive force on the fuel tank vent tube assembly and fuel pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Be sure to keep the handle level when turning it, as SST may slip off the fuel pump gauge retainer if the handle is turned at an angle with excessive force.

·

Do not use an impact wrench or turn the handle with excessive force, as parts may be damaged.

·

If SST slips off the fuel pump gauge retainer, loosen the bolts and reattach SST to the fuel pump gauge retainer.





c.

Remove the fuel tank vent tube assembly from the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



d.
A339566

Remove the fuel tank vent tube gasket from the fuel tank sub-assembly.


Hide 77213B 13.REMOVE FUEL TANK TO FILLER PIPE HOSE

A339622

a.

Loosen the clamp and remove the fuel tank to filler pipe hose from the fuel tank assembly.