Home › Engine / Hybrid System › 1GD-FTV FUEL › FUEL TANK › from 2016.10
RM33K0E _51 Engine / Hybrid System _043571 1GD-FTV FUEL _0222091 FUEL TANK A

1GD-FTV FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A339681C01
2.719,0.698 2.875,0.208 2.875,0.208 3.031,0.208 true 2.115,1.073 2.24,1.073 2.24,1.073 2.469,0.719 true 0.333,1.198 0.427,1.198 0.427,1.198 0.552,1.01 true 3.104,0.104 3.344,0.333 0.24,0.229 10 false *a 1.896,0.99 2.167,1.208 0.271,0.219 10 false *b 0.073,0.635 0.417,0.854 0.344,0.219 10 true 120° 0.906,0.073 1.146,0.271 0.24,0.198 10 true *c 0.552,0.615 0.781,0.802 0.229,0.188 10 true *d 0.135,1.094 0.344,1.281 0.208,0.188 10 false *e
*a Protrusion
*b Paint Mark (White)
*c RH Side of Vehicle
*d Front Side of Vehicle
*e Do not place clamp within this range


Install the fuel tank to filler pipe hose to the fuel tank assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the clamp is oriented as shown in the illustration.



Hide 77010 2.INSTALL FUEL TANK VENT TUBE ASSEMBLY

a.

Apply a light coat of diesel fuel or grease to a new fuel tank vent tube gasket, and install it to the fuel tank sub-assembly.


b.

Install the fuel tank vent tube assembly to the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A346230C02
0.854,0.135 1,0.135 1,0.135 1.667,0.333 true 1.156,2.021 1.302,2.021 1.302,2.021 1.875,1.76 true 0.635,0.042 0.844,0.229 0.208,0.188 10 true *a 0.938,1.938 1.146,2.125 0.208,0.188 10 true *a
*a Protrusion
V100135

Hole


Align the protrusions of the fuel tank vent tube assembly with the holes in the fuel tank sub-assembly.


d.

While pressing down on the fuel tank vent tube assembly, temporarily install the fuel pump gauge retainer.


e.
A391907C01
0.219,3.104 0.458,3.104 0.458,3.104 0.917,2.802 true 2.74,1.833 2.854,2.24 2.854,2.24 3.094,2.24 false 0.99,2.375 1.885,3.073 1.885,3.073 2.125,3.073 true 3.115,2.125 3.427,2.281 0.313,0.156 10 false *a 2.156,2.958 2.469,3.115 0.313,0.156 10 false *b 0.063,2.99 0.375,3.146 0.313,0.156 10 false *c
*a SST (Plate)
*b SST (Claw)
*c Insertion Point
V100135

SST (Bolt)


Set the 2 claws, 2 bolts and plate of SST on the fuel pump gauge retainer.

SST
09808-14031  (09808-01010, 09808-01020, 09808-01030, 09808-01090)
09808-01071  

HINT:

Securely insert the ends of SST into the insertion points in the fuel pump gauge retainer.



f.

While firmly pressing the claws of SST into the insertion points in the fuel pump gauge retainer, tighten the bolts of the claws.


g.

Attach the handle of SST.


h.
A387333C01
2.75,2.229 2.75,1.99 true 0.927,0.167 1.156,0.167 1.156,0.167 1.271,0.594 true 0.875,0.771 1.104,0.771 1.104,0.771 1.229,1.042 true 1.115,3.875 1.51,3.688 false 1.281,4.083 1.5,3.698 false 0.438,3.833 0.656,3.833 0.656,3.833 0.792,4.021 false 1.104,4.479 1.135,4.25 true 1.104,4.479 0.958,4.021 true 1.531,3.594 1.844,3.75 0.313,0.156 10 false *a 1.031,4.5 1.344,4.656 0.313,0.156 10 true *b 2.646,2.24 2.906,2.396 0.26,0.156 10 true *c 0.583,0.052 0.969,0.229 0.385,0.177 10 true SST 0.531,0.677 0.917,0.854 0.385,0.177 10 true SST 0.26,3.74 0.49,3.948 0.229,0.208 10 true *a
*a Alignment Mark
*b Groove
*c Insertion Point
V100135

Turn
V100136

Front of Vehicle


Check once more that the tip of SST is securely inserted into the insertion area of the fuel pump gauge retainer as shown in the illustration.


i.

Using SST, rotate the fuel pump gauge retainer so that the protrusions of the fuel pump gauge retainer are aligned with the grooves in the fuel tank sub-assembly to install the fuel tank vent tube assembly to the fuel tank sub-assembly.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel pump gauge retainer will place excessive force on the fuel tank vent tube assembly and be difficult to remove, and parts may be damaged.

·

Be sure to keep the handle level when turning it, as SST may slip off the retainer if the handle is turned at an angle with excessive force.

·

Do not use an impact wrench or turn the handle with excessive force, as parts may be damaged.

·

If SST slips off the fuel pump gauge retainer, loosen the bolts and reattach SST to the fuel pump gauge retainer.




j.

Insert the fuel tank main tube sub-assembly and fuel tank return tube into the plugs of the fuel tank vent tube assembly and fix them in place with the 2 tube joint clips.

NOTICE:
A339671C01
1.635,1.948 2.052,1.948 true 1.521,2.25 1.885,2.25 true 1.302,2.604 1.427,2.604 1.427,2.604 1.604,2.417 true 2.375,2.521 2.677,2.615 2.677,2.615 2.385,2.417 true 0.635,4.052 0.76,4.052 0.76,4.052 1.01,3.698 true 2.51,3.646 2.792,3.271 2.792,3.271 2.927,3.271 true 1.427,1.854 1.667,2.052 0.24,0.198 10 false *a 1.323,2.156 1.552,2.365 0.229,0.208 10 false *b 2.719,2.521 2.917,2.698 0.198,0.177 10 false *c 1.094,2.521 1.323,2.708 0.229,0.188 10 false *d 0.458,3.969 0.688,4.167 0.229,0.198 10 false *e 0.802,3.177 1,3.375 0.198,0.198 10 false *f 2.208,3.167 2.448,3.406 0.24,0.24 10 false *g 2.969,3.177 3.177,3.333 0.208,0.156 10 false *e
*a Fuel Tube Joint
*b Tube Joint Clip
*c O-Ring
*d Fuel Tank Vent Tube Assembly
*e Collar
*f CORRECT
*g INCORRECT


·

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the tube joint clips are on the collars of the fuel tube joints.

·

After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.

·

Be careful not to damage any clips.

If a clip is damaged, replace it.




Hide 77652A 3.INSTALL FUEL TANK CUSHION

a.

Install the 3 new fuel tank cushions to the fuel tank assembly.


Hide 77697 4.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 4 fuel tank bolts and 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77001A 5.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter and raise the fuel tank assembly.

NOTICE:

Do not allow the fuel tank assembly to contact the vehicle, especially the differential.



b.
A339627C01
1.927,3.188 2.313,3.188 true 1.979,3.813 2.219,4.042 2.219,4.042 2.354,4.042 true 1.208,4.094 1.594,4.094 true 2.375,3.094 2.583,3.26 0.208,0.167 10 false *1 1.01,4.01 1.208,4.177 0.198,0.167 10 false *2 2.396,3.958 2.594,4.125 0.198,0.167 10 false *3
*1 Fuel Tank Cushion
*2 Wire Harness
*3 Fuel Tank Assembly


Fold back approximately half of each fuel tank cushion so that the wire harness can be installed in the step below.


c.

Attach the wire harness to the 6 clamps and connect the fuel sender gauge connector.

NOTICE:

Be careful not to cut the wire harness.



d.

Install the 3 fuel tank bands with the 3 fuel tank band pins and 3 clips.


e.

Install the 3 fuel tank bands with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 77213B 6.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A339682C01
0.927,0.99 1.167,0.583 1.167,0.583 1.271,0.583 true 0.927,1.167 0.417,0.417 0.417,0.417 0.323,0.417 true 0.188,1.156 0.469,1.729 0.469,1.729 0.573,1.729 true 1.344,0.49 1.573,0.677 0.229,0.188 10 false *a 0.125,0.323 0.354,0.51 0.229,0.188 10 false *b 1.49,1.042 1.698,1.229 0.208,0.188 10 true *c 0.615,1.635 0.823,1.813 0.208,0.177 10 true *d 1.479,1.906 1.75,2.104 0.271,0.198 10 true 35° 1.448,2.479 1.74,2.677 0.292,0.198 10 true 55° 0.125,2.146 0.333,2.333 0.208,0.188 10 true *e 0.99,1.781 1.198,1.969 0.208,0.188 10 true *f
*a Protrusion
*b Paint Mark (Yellow)
*c 0 to 3 mm (0 to 0.118 in.)
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e RH Side of Vehicle
*f Top of Vehicle


Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the clamp is oriented as shown in the illustration.



Hide 7.CONNECT FUEL TANK BREATHER HOSE

a.
A339726C01
2.604,1.26 2.875,0.885 2.875,0.885 3.01,0.885 true 3.063,0.792 3.292,0.99 0.229,0.198 10 false *a 2.656,2.396 2.885,2.604 0.229,0.208 10 false *b 2.927,1.208 3.156,1.385 0.229,0.177 10 false *c 1.906,1.177 2.115,1.365 0.208,0.188 10 false *d 2.979,3.198 3.344,3.417 0.365,0.219 10 false 120° 3.167,2.75 3.375,2.938 0.208,0.188 10 false *e
*a Paint Mark
*b Top of Vehicle
*c 0 to 3 mm (0 to 0.118 in.)
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e RH side of Vehicle


Connect the fuel tank breather hose to the fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.

HINT:

Make sure the clamp is oriented as shown in the illustration.



Hide 8.CONNECT NO. 1 EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 evaporation tube sub-assembly to the fuel tank filler pipe sub-assembly.


Hide 77209F 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE

a.

Connect the 2 fuel hoses to the fuel tank main tube sub-assembly and fuel tank return tube, and slide the 2 clamps to secure the hoses.


Hide 77642A 10.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank assembly with the 5 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 77310A 11.INSTALL FUEL TANK CAP ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION